Problem 1: A square concrete column with dimensions 22 x 22 in. is reinforced with a total of eight No. 10 bars arranged uniformly around the column perimeter. Material stress-strain are given by curves a and c in Fig 1. Calculate the percentages of total load carried by the concrete and the steel as load is gradually increased from 0 to failure, which is assumed to occur when the concrete strain reaches a limit value of 0.0030. Determine the load at strain increments of 0.0005 up to the failure strain, and graph your results, plotting load percentage vs. strain. (Source: Design of Concrete Structures 16th ed., McGraw-Hill, 2021) (Hint: use strain compatibility) fs. ksi 60 50 40 30 20 10 O T fc, ksi 9 5 4 3 2 I 0.001 a Steel b Concrete, fast loading c Concrete, slow loading d Elastic concrete 0.002 0.003

Problem 1: A square concrete column with dimensions 22 x 22 in. is reinforced with a total of eight No. 10 bars arranged uniformly around the column perimeter. Material stress-strain are given by curves a and c in Fig 1. Calculate the percentages of total load carried by the concrete and the steel as load is gradually increased from 0 to failure, which is assumed to occur when the concrete strain reaches a limit value of 0.0030. Determine the load at strain increments of 0.0005 up to the failure strain, and graph your results, plotting load percentage vs. strain. (Source: Design of Concrete Structures 16th ed., McGraw-Hill, 2021) (Hint: use strain compatibility) fs. ksi 60 50 40 30 20 10 O T fc, ksi 9 5 4 3 2 I 0.001 a Steel b Concrete, fast loading c Concrete, slow loading d Elastic concrete 0.002 0.003

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the tensile steel ratio of a singly reinforced concrete beam for the following conditions using concrete strength f’c = 21 MPa and steel yield strength fy = 420 MPa. if the tensile strain is set as 0.009 upon crushing of concrete at a strain of 0.003. = [rr] (5 decimal places)
4.1 Consider the prestressed concrete beam and prestressing steel stress-strain diagram given below. The concrete is assumed to have an ultimate strain capacity of 0.003 in/in. Determine the nominal strength of the member using the strain compatibility method. It should be noted that the stress-strain diagram below allows virtually "exact" calculation of stresses and strains in the prestressing steel. Assume that the specified concrete strength is 4,000 psi, fse = 137 ksi, Ec = 3850 ksi, Ecu = 0.003, p = 0.40 and Eps = 28,000 ksi. 20" 4" 3" -10" O -10" (a) 17.58" Ap = 0.575 in.2 fp ksi 250 213 0.0079 Ep (b) 0.067
A cylindrical block of concrete is 300mm long and has a circular cross section of 100mm in diameter. It carries a total compressive load of 67KN and under this load contract 0.2mm. Estimate the compressive stress and strain .
Using Figure 4, a cross-section of a concrete beam, answer the questions that follow.5.1. Calculate the moment of inertia about the X-axis and the Y-axis 5.2 Calculate the combined bending and direct stress at points A, B and C. All loading is assumed to compressive. revision paper 2020
Determine the tensile steel ratio of a singly reinforced concrete beam for the following conditions using concrete strength f’c = 28 MPa and steel yield strength fy = 420 MPa. 1. if the tensile strain is εs = fy/Es upon crushing of concrete at a strain of 0.003. = (5 decimal places) 2. if the tensile strain is set as 0.010 upon crushing of concrete at a strain of 0.003. = (5 decimal places) 3. Minimum as required by NSCP 2015. = (5 decimal places)
4. The state of two dimensional stress acting on a concrete lamina consists of a direct tensile stress of 6 MPa and shear stress of 4 MPa, which cause cracking of concrete. Then what will be the tensile strength of the concrete in MPa.?
Problem 2: If f = 3 ksi what is the modulus of elasticity Ec and the maximum tensile stress fr that the concrete can carry before cracking (use ACI recommended equations). Assume a unit weight of the plain concrete is: a. Wc = 90- b. w lb lb 118- ft39 ft3) C. W = 160- Problem 3: Wight 3-6 Rugblom 4: Wight ? 7 lb ft3
3-1. A concrete cylinder having a diameter of 6.00 in. and gage length of 12 in. is tested in compression. The results of the test are reported in the table as load versus contraction. Draw the stress-strain diagram using scales of 1 in. = 0.05 ksi and 1 in. = 0.2(10-)in./in. From the diagram, determine approximately the modulus of elasticity. Load (kip) 0 5.0 9.5 16.5 20.5 25.5 30.0 34.5 38.5 46.5 50.0 53.0 Contraction (in.) 0 0.0006 0.0012 0.0020 0.0026 0.0034 0.0040 0.0045 0.0050 0.0062 0.0070 0,0075
What is the stress in an 8-inch round x 16-inch high concrete cylinder (E = 2.5 x 10^6 psi) when the unit deformation is 0.0012 inch/inch? A. 500 psiB. 8100 psiC. 210 psiD. 3000 psi
Two 150 mm * 300 mm concrete cylinders with randomly oriented steelfiber contents of 0 and 2% by weight, respectively. After curing for 28 days,the specimens were subjected to increments of compressive loads until failure. The load versus deformation results were as shown in Table P7.45. Assuming that the gauge length is the whole specimen height, determine the following:a. The compressive stresses and strains for each specimen at each loadincrement.b. Plot stresses versus strains for the two specimens on one graph.c. The initial modulus of elasticity for each specimen.d. The ultimate strength for each specimen.e. The strain at failure for each specimen.f. Toughness. Curves may be approximated with a series of straight lines.g. Comment on the effect of adding fiber on the following:i. Modulus of elasticityii. Ultimate strengthiii. Ductilityiv. Toughness
solve the following problems 1. A concrete has a height of 5 meters and has unit area of 3 m². It supports a mass of 30,000 kg. Acceleration due to gravity (g) = 9.81 m/s². Young's modulus of concrete = 20x 10¹ N/m² Determine (a) the stress (b) the strain (c) the change in height.
2.13 Consider a rectangular reinforced concrete beam. Draw a diagram showing the beam internal stresses after concrete cracking occurs under bending moment. Identify the concrete zone under compression stress and reinforcing bars tension.