Practice Problem 9.12 Find I in the circuit of Fig. 9.30. I Answer: 6.364/3.8° A. j4 2 -j3 Q 8Ω J5 Ω le 30/0° V 9.8 † Applications 5Ω In Chapters 7 and 8, we saw certair in dc applications. These circuits als are coupling circuits, phase-shifting bridge circuits, and transformers. T 10 Ω -j2 N Figure 9.30 For Practice Prob. 9.12.

Practice Problem 9.12 Find I in the circuit of Fig. 9.30. I Answer: 6.364/3.8° A. j4 2 -j3 Q 8Ω J5 Ω le 30/0° V 9.8 † Applications 5Ω In Chapters 7 and 8, we saw certair in dc applications. These circuits als are coupling circuits, phase-shifting bridge circuits, and transformers. T 10 Ω -j2 N Figure 9.30 For Practice Prob. 9.12.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.22P: The real power delivered by a source to two impedances, Z1=4+j5 and Z2=10 connected in parallel, is...

See similar textbooks

Similar questions

Figure 2 shows three "LC" circuits, two of them with capacitance capacitors "C" and the three with inductance coils "L", the three circuits are coupled by means of two capacitance capacitors "Cc". The currents that circulate through each mesh are those indicated in the figure: "I1", "I2" and "I3". Using Kirchhoff's law for voltages and taking into account the definition of current I = −dQ / dt, find the system of coupled equations of the system and then find the normal angular frequencies of the system.
An AC voltage of 230 v is applied to a circuit consisting of a resistance of 10 ohms in series with an inductive reactance of 7 ohms. Find the power, reactive power and the power factor of the circuit. If a capacitor is connected in parallel with the RL series circuit of the preceding problem and if this capacitor supplies 1000 var, find the true power and the reactive power supplied by the 230 v source and find the resultant power factor.
d. 565.685 V If a Load absorbs 20 kVA at a leading power factor of 0.6. Then the complex power is: Select one: O a. 12000 - j16000 VA O b.-12000 + j16000 VA O c. 12000 + j16000 VA O d. None of these Given the circuit below and the associated set of voltages and currents, the reactive Power developed by im voltage source is FENG300 MINTERM
An impedance z₁ = 8j5ohms is in parallel with an impedance z₂ = 3 + j7ohms. If 100V are imposed on the parallel combination. Find the branch current 11, 12 and the resultant current. Draw the corresponding phasor diagram showing each current and voltage drop across each parameter. Calculate also the equivalent resistance, reactance and impedance of the whole circuit.
9. A noninductive load with a resistance of 30 Q2 is connected in series with a capacitor. The capacitor has a capacitive reactance of 25 Q and negligible resistance. The series circuit is energized from a 210 V, 60 Hz source. Determine: a. the impedance of the series circuit. b. the current, in amperes. c. the loss in volts across the noninductive resistance load. d. the loss in volts across the capacitor.
An impedance load consisting of 12 ohms resistance and 16 ohms inductance reactance is connected across a 50 Hz, 100 V source. Find the capacitance of the condenser which may be paralleled with this load to bring the power factor to 0.80 leading.
The picture shows three LC circuits, two of them with capacitors of capacitance C and the three with coils of inductance L, the three circuits are coupled by means of two capacitors Cc capacitors.L inductance coils, the three circuits are coupled by means of two capacitors of capacitance Cc. The currentscirculating through each mesh are those indicated in the figure: I1, I2 and I3. Using Kirchhoff's law for voltagesand taking into account the definition of current I = -dQ/dt, find the system of coupled equations for the systemand then find the angular normal frequencies of the system.
A DC-DC Chopper Circuit with an RL Load has an output current waveform shown below with a duty cycle of 50% and 1ms period. If it has a resistance of 1ohm and an inductance of 10mH, find the source voltage. 5A 2A ton toff output _current
A pure resistance of 50 ohms is in series with a pure capacitance of 100 microfarads. The series combination is connected across a 100 volt, 50 hz source. Find the a) impedance, b) phase angle, and c) equation of the current
1 In the system shown in the below figure, the switch is closed at t = 0. a Determine voltage reflection coefficient at the load and the source b. Sketch the bounce diagram of the VOLTAGE and the CURRENT and give sufficient information on it (up to 4us) C. Sketch diagram of voltage and current at source and load Mittetu Md. Calculate the steady state Vss. Vss and Iss. Iss opinti 15 Wan httons e. Find the value V(z-50m 1.7us) TERS Wertens atom Dett th will MARRI E yo w B pinn WERS THIS Suprin 90 MAKEL R₂=90 0 3 CAP 180. Rr = 180 Q - i T Mart 1800 H SUS Vg=90 V HIE 1 D = min 200 thin 1 FARG - Bilare. Radio T 149 SATISH SET Pan PARACHUNG G IN Sulta Ap 135 aytinius - FORES exotic Me GALER 2 Mer t=0 400 NITINE atas Aper SUMB satan THE SIM- " WAS Thy POST ANE nicht www.M upp 6 HIS 328 20 p Hifiq Z. = 60 52 WHAT p=10m/s 459 w 30 Patie SATE 108 1 = 100m MNA A
For the circuit shown in Figure,a. Find the Thévenin equivalent circuit for the source.b. Find the power dissipated by the load resistor. c. What value of load impedance would permitmaximum power transfer?The voltage source is sinusoidal with frequency60 Hz, and its polarity is such that the current fromthe voltage source flows into the 10-Ω resistor.
9. An electric circuit consists of two components as shown in the figure below. Z1 R₁ www XL 1 00000 = Z2 HE The generalisation of the resistance and reactance to an AC circuit is a complex number, known as impedance. For the electrical circuit pictured above, the impedance of the first component can be expressed by z₁ = R₁ + X₁i and the impedance of the second component can be expressed by z2 = R₂ - Xci, where R₁ = 3 Q2, XL = 32, R₂ = 42, and Xc = 422. Z Z1 Z2 R2 For electrical circuits connected in parallel, as shown above, the total impendance z of the circuit can be computed using the relationship Xc (a) Compute the total impedance z of the two components. (b) What are the modulus and principal argument of the total impedance?