OUT IN1 Rd 100 V1 R3 20k Rc 100 Re 10k IN2 R2 1 Meg 12 ↑ Rb 50 IN3 ↓ Ra 50 13 Answers: V1 = 12- 13- Vout= R1 1Meg 1. Set V1 to n Volts where n is equal to Name Code 1 2. Find the values of 12 and 13 so that the output voltage OUT will be half of n (i.e. OUT = n/2). Express your answer in 4 decimal places (except if the value is in whole number).

OUT IN1 Rd 100 V1 R3 20k Rc 100 Re 10k IN2 R2 1 Meg 12 ↑ Rb 50 IN3 ↓ Ra 50 13 Answers: V1 = 12- 13- Vout= R1 1Meg 1. Set V1 to n Volts where n is equal to Name Code 1 2. Find the values of 12 and 13 so that the output voltage OUT will be half of n (i.e. OUT = n/2). Express your answer in 4 decimal places (except if the value is in whole number).

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 3-bit ADC with a reference of 10V is used to sample a DC signal. What is the outpout D2.DO for an analog input Vin= 3.349 V Select one: O a. D2.D0 = 100 O b. D2.DO - 101 Oc. D2.D0= 011 O d. D2.D0 = 111 Oe. None of the mentioned.
Calculate the output for the given circuit . R2 R2 Voa R1 Let the values are R1=775.8ohm,R2=506.8 ohm .The error voltage is =8.3 Volt and the initial value of output is 3.7 Volt. Vout = volt.
Q 1. Determine the output voltage of the Digital-to-Analog Converter (DAC) in Figure 1(a) and plot it in Figure 1(c). The sequence of the four digit binary codes represented by the waveforms in Figure 1(b) are applied to the inputs. A high level is a binary 1and a low level is a binary 0. The least significant binary digit is Do. Do o D₁ 0- 200 ΚΩ www D₂ 0 100 ΚΩ www 50 ΚΩ www 25 ΚΩ D3 0 M 0 -0.25 -0.50 -0.75 -1.00 -1.25 -1.50 -1.75 -2.00 -2.25 -2.50 -2.75 -3.00 -3.25 -3.50 -3.75 (a) Vout (V) R₁ 10 ΚΩ o Vout +5 V Do 0 +5 V D₁ 0 +5 V 0 +5 V 0 D₂ D3 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 non (c) Figure 1 I 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111 ||||| (b) Binary input
M1 and M2 are matched, what is the output common mode voltage? Draw the output wave form if Vi is a sine wave of 10MHz and peak amplitude of Vdd/4, assume high gm, long channel, find the output signal shape, frequency and peak to peak amplitude, Rin ww RF VDD M2 M1 Rout
24. A step up chopper has load voltage of 600V and is sup- plied from a constant de source of 150V. If the OFF time of the chopper is 40 µs and desired output voltage is 300V find ON time of the chopper? (A) 5 µsec (C) 30 µsec (B) 10 μsec (D) 40 µsec
Let the values are R1=622.8ohm,R2=915.95 ohm ,The error voltage is =7.9 Volt.and the initial value of output is 5.5 Volt. Vout =
b.com Snubbers are an essential part of power electronics to protect the active devices. Design a snubber circuit and explain how thyristors are protected against high di/dt and high dv/dt.
A 3-bit binary weighted resistor DAC and a 3-bit R-2R ladder DAC have common values of Vref = 5V, R = 1kN, R = 2kN. Compare their output voltages for each of the following binary inputs. What do you observed? Binary Weighted Resistor DAC Resolution Binary input R-2R Ladder DAC Output voltage Resolution Output voltage 000 001 010 011 100 101 110 111
. An 8-bit A/D converter has an input range of +/-8V. If the input is 7.5V, what is the quantization error (in +/-V)? - An 8-bit A/D converter has an input range of +/-8V. If the input is 7.5V, what is the quantization error as a +/-% of input voltage?
For the circuit shown in below, determine and sketch the output waveform for the give input signals: - Vini = 2 sin(wt) Vinz = 1 volt 100 k Ohm 50 k Ohm V_out 50 k Ohm V_in1 100 k Ohm V_in2
The output of the folloung than Vpo-VT. crravit cannot go (Voo = 1V,VT=03 V,ignore the baby eftect). eftfect). out in a) why? (kink: Vgs LUz → Io=0) b) What is going to be the max autput voltages for the fellaung crcuits. (laputs ore rising from o to l) b-4) in. out 0→1 b.2 ) 031. out 0-1
Design a 6-bit digital to analog converter with binary weighted resistive ladder network sothat the analog output for the bit sequence 100100 is -X1X2 V.