Member AC is subjected to the loading shown in the figure below. Determine the force P if the position x-120 mm of this force so that the average compressive stress at the smooth support C is equal to the average tensile stress in the tie rod AB. The rod has a cross sectional area of 350 mm² and the contact area at C is 600 mm²

Member AC is subjected to the loading shown in the figure below. Determine the force P if the position x-120 mm of this force so that the average compressive stress at the smooth support C is equal to the average tensile stress in the tie rod AB. The rod has a cross sectional area of 350 mm² and the contact area at C is 600 mm²

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2. The bar AC is supported by a pin at A and a cable that runs from B to E around the frictionless pully at D. If the allowable tensile stress oallow = 5.2 ksi for the cable, determine the required minimum diameter (inch) of the cable. The cylinder (connected at C) weighs 890 lb. Neglect weight and thickness of the bar AC. D 4 3 A C 5 ft 5 ft -4 ft 890 lb
The vertical shaft with a diameter of d = 20 mm is supported by a thrust collar that rests on a 21-mm-thick plate. The thrust collar is 16-mm thick. Assume that the load P causes a compressive stress of 190 MPa in the shaft. If the bearing stress between the thrust collar and the plate is limited to 35 MPa, determine the minimum outer diameter Dcollar that must be used for the thrust collar. Thrust collar area Plate Thrust collar d Dcollar
A weight W = 905 lb is held up by two cables each with a diameter of 1.5 in. Determine the tension in each cable and the normal stress in each cable. 0 = 21° O = 37° B Image is not drawn to scale.
2-1. The steel framework is used to support the reinforced stone concrete slab that is used for an office. The slab is 200 mm thick. Sketch the loading that acts along members BE and FED. Take a = 2 m, b = 5 m. Hint: See Tables 1.2 and 1.4. B 8 E D
The way to the column where the loading status is seen determine the P load required for the 5 mm horizontal displacement of the C midpoint and the maximum shear stress that this P load will generate. b=750mm a=50mm t=4mm e=48mm E(modulus of elasticity)=70GPA
The boom supports the two vertical loads, F, : = 800 N and F2 = 350 N. Neglect the size of the collars at D and B and the thickness of the boom. (a) Determine the average normal stress in the 20 mm diameter cable BC. 4 (b) Determine the average shear stress in the 10 mm diameter pin A. (c) Suggest an appropriate diameter for cable BC if it is made from material having tensile yield stress of o, = 250 MPa. 1 m B 1.5 m D. F2 30° A F,
The rigid bar AB of negligible weight is supported by a pin at 0. When the two steel rods are attached to the ends of the bar, there is a gap D= 4 mm between the lower end of the left rod and its pin support at C. Compute the stress in the left rod after its lower end is attached to the support. The cross-sectional areas are 300 mm2 for rod AC and 250 mm2 for rod BD. Use E= 200 GPa for steel. lo/0 0.75 m 1.5m 2 m ANSWER: MPa
Problem 3, The metal stud punch is subjected to a force of 120 N on the handle. Determine the magnitude of the reactive force at the pin A and in the short link BC. Also, determine the resultant internal. loadings acting on the cross section at point E. B 50 mm 100 mm 4 50 mm D 100 mm 200 mm 120 N 300 min
The solid circular rod has a cross-sectional area of 470 mm². It is subjected to a uniform axial distributed loading along its length of w = 8 kN/m. Two concentrated loads also act on the rod: P = 5 kN and Q = 7 kN. Determine the normal stress in the rod at x = 1.4 m. Assume a = 0.5 m and b = 1.2 m. A -> a Answer: 0 = i B W b C MPa Q
The compound wooden beam is connected together by a bolt at B. Assuming that the connections at A, B, C, and D exert only vertical forces on the beam, determine the required diameter of the bolt at B and the required outer diameter of its washers if the allowable tensile stress for the bolt is 1st2allow = 150 MPa and the allowable bearing stress for the wood is 1sb2allow = 28 MPa. Assume that the hole in the washers has the same diameter as the bolt.
The horizontal force of P = 80 KN acts at the end of the plate. The plate has a thickness of 10 mm and P acts along the centerline of this thickness such that d = 50 mm. Plot the distribution of normal stress acting along section a-a.
4. The cable will fail when subjected to a tension of 8000 N. Determine the largest vertical load P the frame will support and compute theresultant internal loadings at the cross section through point C. Answer: P = 2133.33 N, Mc = 1600 Nm, Nc = 8000 N, Vc = 2133.33 N 0.1 m 0.5 m C 0.75 m- -0.75 m- -0.75 m-