Do anything I have to do submit fast just do anything u know Ls2Ps1212Figure Q2b ( Figure Q2b shows the schematics of an escape hatch (made of two joint rectangularsections). Calculate the minimum torque (T) necessary to start opening it at a depthLs2 = 10m. The water density is 1.03 kg/l, and the pressure (Ps) on the submarine sideequals atmospheric pressure at the ocean surface. In =0.4m, l2= 1.2m, l3= 1.5m, and0 = 70°.

The given question is related to the force on submerged areas in the fluid. Since the gate is fully…

Answered: Ls2 Ps Figure Q2b

Engineering

Mechanical Engineering

Ls2 Ps Figure Q2b

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please I want you to solve the question below in the same way that I provided in another. picture I want to you to include F_R. also the coordinator x_R and YR. and x_C and y_C. also I want to know the h_C. The gate in the figure below is 5 ft wide, is hinged at point B, and rests against a smooth wall at point A. (1) Compute the force on the gate due to water pressure (Must include the magnitude and the center of pressure) (2) Compute the horizontal force exerted by the wall at point A. (3) Compute the reaction force at the hinge B (Must include the magnitude and direction
Find Ixx for the given Plane, where b1 =120m, d;=25m, b2=20m, d2=120m, b3=50m & d3=25 m (Enter only the values in the boxes by referring the unit given in brackets. Also upload your hand written answers in the link provided) b3 d3 b2 d2 di bị
For the tank shown below. The base of tank is semicirele, if the length of tank is (10m) find: 1. Vertical force on the base of tank (point C). 2. Horizontal force at the arc (BC). 3. Force acted on the inclined wall of tank (AB). 40° 40 oil, s:3= 2-1 3m B. 2m
Figure Q5 shows a radial gate, where fluid of specific gravity (s.g.) of 0.437 is contained. If it is 30 m long (into the page), find the magnitude and direction of the resultant force acting on it. The radius to the gate is 3 m. 10 C - 104 degree
A concrete block is attached to the gate as shown. If the water level is 1.3 m from the bottom of the container, there is no reaction force at A.What would be the reaction force for the level shown?Note 1: Specific gravity of concrete is 2.4.Please show clear workings with explanations to steps taken. I don't just want the answer, I want to understand the process to answering this question. Thanks
a drum has gasoline s.g=0.9, with oil s.g=0.8 and sea water s.g=1.03. the depth of the liquid is 0.8m, 0.5m, and 1.0 for gasoline, oil and sea water.1. find absolute pressure at depth 1.2m 2.find the depth at 1.8m 3. find the force F at depth 2.1m when diameter of drum is 0.5m
QV: a hydraulic press is used to compact powdered samples. The device is made of two interconnected cylindrical chambers filled with oil if density psubscripto anc closed by two pistons. The small chamber on the right has diameter d and the large chamber on the left has diameter 5d. A lever is attached to the piston pushing down on the fluid in the small cylinder. The horizontal lever is hinged on the left, at distance L from the small piston, and a force of magnitude Fsubscript0 is applied vertically down at distance 2L from the hinge (Fig.5). You may assume that the lever and pistons have negligible mass. a. Determine the magnitude of the force Fin that the small piston exerts on the fluid in the small cylinder. Hint: you may consider that the lever is at rest in the horizontal position. b. Determine the pressure change applied to the fluid by the small piston. c. Determine the magnitude Fout of the force that the fluid applies to the large piston.
है water 2m diameter circular gate 3m 160⁰ CAREFUL WITH UNITS!! a) Find the magnitude F and point of application y R of the water force on the circular gate shown. Notice: 3 m to top of gate. Also, recall: circle | = pi D4 / 64. b) Also, if the liquid were crude oil (S.G. = 0.86), what would the force magnitude be? -
A piece of cork has a specific gravity of 2.36 kN/m3 and the shape shown in the figure. a. How deep will it be immersed in turpentine (sg = 0.87) if placed in the displayed orientation? b. Will you have stability in that position?
3m Q4/ Find the pressure force and position of center of pressure on a triangular plate of base 2m and height 3m which is immersed in water in such a way that the plane of the plate makes an angle of 60° with the free surface of the water. The base of the 2.5m 2m plate is parallel to the water surface and at a depth of 2.5m from water surface.
Force due to Liquid PressureProblem 3: A gate is in the form of letter T with the vertical 2 ft wide and 4 ft high. The horizontal crosspiece is 6 ft long and 1 ft high. Find the force on one side if the gate is submerged vertically with the top of the crosspiece along the surface of water
1- Panel BC in the figure is circular. Compute (a) the hydrostatic force of the water on the panel; (b) its center of pressure; and (c) the moment of this force about point B. Given and unknowns: Assumptions: Schematic: Governing Equation(s): Analysis and Results: Water at 20°C C 50° B 3 m 3 m 3 m