linear interpolation.. (square) Solution for 1 side and 1 diagonal line only. Indicate the scale of

Q: Determine the operating conditions (HP, Q, ep, and Pi) of a pump capable of moving water (68°F) from…

A: Given, D = 12" or 1 ft L = 8700 ft  e = 0.006 ft    NOTE : As per guidelines, only first question…

Q: 4.33 The 1200-kg car is being lowered slowly onto the dock using the hoist A and winch C. Determine…

A:

Q: Q-A double-acting reciprocating pump having a piston area of 0.1m² has a stroke 0.30 m long. The…

A: Given data- Double-acting reciprocating pump- Piston area A=0.1 m2, Stroke L=0.3 m, N=45 rpm, Height…

Q: A B 2m 4m H 3m 4m с 200KN D 4m 4m G F 4m 400KN E Find member CD, DG and FG

A:

Q: H.W-2: For a soil sample, FC = 28% by dry weight, PWP = 18% by volume, and PAD= 50%. Find the…

A: Given that, FC =28% by dry weight  PWP = 18% by volume PAD =50% Bulk specific gravity =1.35 Readily…

Q: -75 ft- 480 lb OC Using the method of joints, determine the force in each member of the truss shown.…

A:

Q: A beam of symmetrical l-section spanning 8 m has a flange width of 150mm & flange thickness of 80 mm…

A: I beams utilize the least amount of material while still obtaining the appropriate shape and…

Q: QUESTION 1 Complete the table below. LINE BEARING DIST (M) AB N 60° 15.3' E 40.311 BC S 64° 5.6' E…

A: To Find : Latitudes ,Departures, DPD , Double Area ( DA ) and Area for traverse. Given: LINE…

Q: Find the reactions at supports A and B for the beam given below. The length of the beam is 10m and…

A: Given  Length of beam = 10 m

Q: Determine the y-coordinate of the centroid of the area under the sine curve shown. 3 Answer:y= = i…

A:

Q: Question 3 Determine the reactive forces at support A and B. 6m -8m 12m 40KN B

A:

Q: ENGINEERING MECHANICS

A:

Q: The solid cylinders AB and BC are bonded together at B and are attached to fixed supports at A and…

A: Shear stress due to torque: Torsional shear is shear caused by torsion applied to a beam. Torsion…

Q: Find the centroid point of the area below given that a = 12 in. a a Solution: • The composite area…

A: Given data:- The given value of a is 12 in. After cutting the section,

Q: Consider the overhang beam shown in (Figure 1). Suppose that P = 4 kN, M = 8 kN·m, w = 2 kN/m .…

A:

Q: Two dimensional stress system on a block made of a material with Poisson's ratio of 0.3 is shown in…

A: No change in length Ab Means Total elongation in line AB must be zero  Due to 60N/mm2 Bar AB being…

Q: ENGINEERING MECHANICS (UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTIONS AND FBD LEGIBLY. NO…

A: To find force exerted by CB on E

Q: A tank initially contains 200 gallons of water in which 50 lbs of salt are dissolved. A salt…

A:

Q: The principal stresses in the wall of a container are 40MN/mm2 and 80MN/mm2. The normal makes an…

A: Given :- σx = 80 MN/mm2 σy = 40 MN/mm2  τxy = 0 θ = 30° To Determine :- The resultant stresses, σR

Q: 2. Determine the member end moments and reactions for the frame shown in the figure by using…

A: Given data:

Q: Determine variables requested below for a horizontal curve with the following characteristics.…

A: Given Data: The data for the horizontal curve is given as: lane width=14ftnormal…

Q: 2. The composite shaft, consisting of aluminum, copper, and steel sections, is subjected to the…

A:

Q: When a round bar material with diameter of 37.5 mm, length of 2.4 m, Young's modulus of 110 GN/m²…

A:

Q: • Calculate the total stress at A: OA=_lb/ft²

A:

Q: nd of each segment of the structure shown in Figure below. Sketch the bending moment and shear force…

A:

Q: water level outside is constant at point 2, how long will it take the level in the cone to drop from…

A:

Q: Calculate the moment Mo of the 250-N force about the base point 0 of the robot. 400 mm 20⁰

A: Given : Force = 250 N Calculate the moment Mo about the base point O ?

Q: Properties of Materials When a round bar material with diameter of 37.5 mm, length of 2.4 m, Young's…

A: Given- Diameter d=37.5 mm, Length L=2.4 m, E=110 GN/m2=110 GPa, G=42 GN/m2=42 GPa, It is needed to…

Q: Determine the value of bending moments at the support using method distribution method W₁ M₁…

A: Given: I = 2 To find: The value of bending moments at the support using method distribution method.

Q: Q2/ The viscosity of a certain fluid is 5 x 10- poise. Determine its viscosity in both SI and BG…

A:

Q: A 2033.8-lb tractor is used to lift 900 lb of gravel. Determine the reaction at each of the two…

A: Objective: To determine the reaction at each of the two front wheels of the tractor.   Given: Weight…

Q: 8. A square area of a land was measured on the ground, the length of one side was (500 m). What is…

A: Length of one side of Square = 500 m  Square all four sides are equal. Hence area of Square land in…

Q: Q-Retaining walls- A 6 m high retaining wall with a vertical back has a backfill of silty sand with…

A: Given data- Height of retaining wall H=6 m, Slope angle=10o, Backfill values KH=760 kg/m2/m,…

Q: Draw the axial load, shear and bending moment diagrams for the frame shown

A: A frame is given with both ends hinged support. A horizontal point load of 5 kN is applied at the…

Q: A crew consisting of two carpenters and one helper can fix 10m² of a slab formwork in 8 hours, and…

A: Given data: A crew consisting of two carpenters and one helper can fix 10 m2 of a slab formwork in 8…

Q: Homework Draw the Axial Force Diagram (NFD), Shear Force Diagram (SFD) and Bending Moment Diagram…

A:

Q: The height of a theodolite held at hill A is 1.2 m, hill C is between hill A and B. The elevation of…

A:

Q: Draw shear and moment diagrams. Show calculations "| 5 kips/ft 6 ft 9 kips/ft B 10 ft C 11 ft X

A: Given data  Draw shear force and moment diagram.

Q: Q- Head at the base of the nozzle = 32 m, Discharge of the nozzle = 0.18 m³/s Area of the jet= 7500…

A: Given data- Head at the base H=32 m, Discharge Q=0.18 m3/s, Area of jet a=7500 mm2, Power P=44 kW,…

Q: e offset observation

A: Introduction- In Worldwide Route Satellite Framework (GNSS) people group, pseudorange observables,…

Q: Q3. A plate shown in Figure 3, is submerged in oil (s = 0.9) and lies in vertical plane. Find the…

A: Given : S = 0.9  Determine the magnitude and location of hydro static force acting on one side of…

Q: the reverse curve is 15°. The radii of the first, second and third curve are 190.986 m, 381.97 m,…

A: Given:- The radii of the first, second and third curve are 190.986 m, 381.97 m, and 159.155 m angle…

Q: 5. Two hard rubber blocks are used in an anti-vibration mount to support a small machine as shown in…

A: Given Data : P = 150 lb Downward deflection = 0.25 in. a = 0.5 in., b = 1.0 in. and c = 2.5 in. To…

Q: resultant of applied pressure act within the middle third of the footing? (c) Compute the minimum…

A:

Q: 3.46 During a storm, wind exerts a pressure of 130 N/m², normal to the surface of the stop sign.…

A:

Q: Consider the following data with respect to the design of flexible pavement: Design wheel load =…

A: Given- Design wheel load P=4200 kg, Tyre pressure p=6 kg/cm2, E=150 kg/cm2, Deflection=0.25 cm, It…

Q: Complete the table below. LINE BEARING DIST (M) AB N 60° 15.3' E 40.311 BC S 64° 5.6' E 38.910 CD S…

A: A closed traverse ABCDEA is given. The fore bearing and distance of each line are mentioned. To…

Q: The circular disk of radius r = 0.40 m rotates about a fixed axis through point O with the angular…

A:

Q: A Civil Engineer is considering establishing his own company. An investment of P4,000,000 will be…

A:

Q: 1. A ball, attached to a string, is being spun around in such a way that the speed of the ball is…

A: "Since you have asked multiple question, we will solve the first question for you. If you want any…