In the accompanying figure A, B, and C are three known control stations and P is the position of a sounding vessel which is to be located. If b 6925.50m, c 6708.40m, angle BAC = 112"45'25", angle alpha = 25°32'40"and angle beta = 45 35'50". Find the following: A. Value of angle X B. Value of angle Y C length of m or AP

In the accompanying figure A, B, and C are three known control stations and P is the position of a sounding vessel which is to be located. If b 6925.50m, c 6708.40m, angle BAC = 112"45'25", angle alpha = 25°32'40"and angle beta = 45 35'50". Find the following: A. Value of angle X B. Value of angle Y C length of m or AP

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

4. In the accompanying figure A, B, and C are three known control stations and P is the position of a sounding vessel which is to be located. If b = 6,925.50m, c = 6,708.40m, and angle BAC 112°45'25, angle a = 25°32'40", and angle ß = 45°35'50". a. Compute the angle of value X. b. Compute the angle of value Y. c. Compute the length AP. (Control Station) water A JAngle BAC Sounding Vessel (Control Station)
TP1 4.20 6.02 21+80 5.80 22+00 5.95 22+50 6.05 BM2 5.83 451.06 3. The bearing of line AB is N 50°16'08" E, and the bearing of line AC is N 64°23'32" W. What is angle +C BAC? 4. Suppose that a line has been observed 10 times using the same equipment and procedures. The results are shown below and it is assumed that no mistakes exist, and that the observations have already been corrected for all systematic errors. Compute the most probable value for the line length and the standard deviation. 64.25.32 Length (ft) 538.57 538.39 538.37 538.39 538.48 538.49 538.33 538.46 538.47 538.55 5. For the section shown, sections S1 and S2 are spaced 100 ft apart. The dimensions of Si and S2 are as given in the table below. Determine the area of the midsection in a prismoidal computation of the volume of dirt removed. Section 40.0 ft 5.67 ft 0.5 50.0 ft 7.14 ft 0.5 S1 S2
In the accompanying figure A, B, and C are three known control stations and P is the position of a sounding vessel which is to be located. If b = 6925.50m, c = 6708.40m, angle BAC = 112°45’25”, angle alpha = 25°32’40”and angle beta = 45°35’50”. Find the following:D. Length of d or BPE. Length of e or CPF. Angle thetaG. Angle Phi
From the following measured interiror angles of a five sided figure, compute the following: Station Values of Angles (No. of Measurements A 110.00 98.000 108.00 120.00 105.00 BUDE с 5 NOTE: Final answer must be in decimal degrees. HINT: Sum of Interior Angles = (n-2)*180* NAO сл 6 4 2 1 a) Probable value of Angle A. b) Probable value of Angle C. °c) Probable value of Angle D
ANSWER KEY=D 108.1502m∆h 22.4596m
ANSWER KEY: D= 195.9868m∆h =29.5209m
If the 4 holes in the drawing below are produced at .410" in diameter, what is the total positional tolerance of the holes? O .040 O .020 O .035 D O .410 Ø3.000 .020 45° 4X Ø.395-.430 Ø.500-.510 0.020MABMCM +0.010M ADM -.375-.395 +.000MABM C Ø2.000 A 0.005MA B
Question: 1 To determine the elevation of station A, the following observation were taken, the rod held vertically. The instrument fitted with Anallatic lens and value of constant was 100. Inst. Station Height of instrument Staff Station Vertical angle Staff Reading Remarks O 1.440 B.M - 5o40’ 1.332 1.896 2.460 R.L of BM = 158.205 m B 1.440 C.P +8o 20’ 0.780 1.263 1.746 A 1.380 C.P -6o 24’ 1.158 1.617 2.076 subject: Engneering surveyin 1
Item I. In the figure shown, A, B, and C are three known control stations and P is the position of a sounding vessel which is to be located. If b = 6,925.50m, C = 6,708.40m, angle BAC = 112°45'25", angle alpha (a) = 25°32'40", angle beta(B) = 45°35'50". 15°45'53" AB (Control Station) T E KA Angle BAC Sounding Vessel C(Control Stat lon) 1. In item No.I, what is the value of angle X? a) 17°33' b) 15°46 c) 20°23' d) 18°10'
A-15 m- 33 m Q2) The figure to the right shows a rectangle ABCD, in which A, B, and C are the stations where staff readings were obtained with a level set up at E and D. The observed readings are given in Table. 20 m Staff reading at level location A B C 1.85 0.803 D 2.42 1.361 1.659 48 m If A is a benchmark having elevation of 70 m. Note: the deflection angle in Line of sight (5) is + 0.1146 degree. Level 1. calculate the correct elevations B and C 2. if the height of instrument at E = 1m, and at D= 1m, what is the height difference between D and E
Q3: A: Draw the diagram of traverse classification. B: In closed traverse ABCD. The partial coordinates were known as shown below. Determine its area by DMD method. 04 N Dofland OWODY dienstl it with (nm) dinostim Mem. AB BC CD DA ΔΧ 40 -80 -50 AY 60 100 -70
B. Double-Rodded Leveling 3. Complete differential level notes for the information shown and perform the customary arithmetic check. STATION BS HI FS STATION 1.722 BM1 127.378 m 1.722 ΤΡΙΗ 2.623 1.382 TP1L 2.789 1.522 TP2 H 3.089 0.899 TP2 L 3.214 0.714 ТРЗ Н 1.521 2.452 TP3 L 1.632 2.678 ТРА Н 2.333 1.113 TP4 L 2.589 1.523 TP5 H 0.667 2.877 TP5 L 0.986 2.543 3.521 BM2 3.214