In abalanced Three Phase System The Source is balanced Wye With an abc – Phase Sequence and Vab = 215 250 Vms The Load is balanced Wye paralle with ablaned delta . the phase impedance of Wye is 9 + j3 and the phase impedance of the delta is find the line impedance 1+ j0.8 N find the line currents and phase currents in load . %3D

In abalanced Three Phase System The Source is balanced Wye With an abc – Phase Sequence and Vab = 215 250 Vms The Load is balanced Wye paralle with ablaned delta . the phase impedance of Wye is 9 + j3 and the phase impedance of the delta is find the line impedance 1+ j0.8 N find the line currents and phase currents in load . %3D

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.14MCQ: The instantaneous power absorbed by the load in a single-phase ac circuit, for a general R LC load...

See similar textbooks

Similar questions

1. Given the circuit below, the phase voltages are given by Van = 20040° Vrms. The source impedance is 5 + j7 per phase and the wire impedance is 8 +j10 per phase. Let the load impedance be Zy = 50 ohms. Find: Van Vin Ven a. II, and Ic b. c. VAN, VBN, and VCN, and VAB, VBC, and VCA Z₂ Z₂ Z₂ Zw Zw Zw B C le N
Two impedances are connected in parallel to the supply; the first takes a current of40A at a lagging phase angle of 300, and the second a current of 30A at a leadingphase angle of 450. Draw a phasor diagram to scale to represent the supply voltageand these currents. By calculation, determine the total current taken from the supplyand its phase angle. All currents are expressed in their r.m.s. values
Draw a 3-phase wye-connected generator with transmission lines connected to a 3-phase delta-connected load. Assume the lines connecting them have an inductance of j5 per phase. The generated voltages are 120 Vrms with phase 'a' having a phase angle of 0°. The loads are 10 Ohm resistors per phase. When drawing, make sure to label all 3 phases with voltage phasors, line inductances, and load resistances.
A balance delta load with impedances of 15-j9Ohms is connected to a three phase source by three wires each of which has 2+j5ohms impedance. The load phase voltage is 120v. Find the line voltage of the source.
Given at the load: Vioond = 452-25° VRMS, 452-25° VRMS, Iload What are the real and reactive power and power factor at the load? Exclude the units. real power: reactive power: power factor: Iload-10-25 ARMS what type of impedance is seen at the load? R. L. or Ch
Two impedances are connected in parallel to the supply, the first takes a current of 40 A at a lagging phase angle of 30°, and the second a current of 30 A at a leading phase angle of 45°. Draw a phasor diagram to scale to represent the supply voltage and these currents. From this diagram, by construction, determine the total current taken from the supply and its phase angle.
In a balance three-phase system, the source has an abc-phase sequence and is connected in delta. The line connecting the source to the loads has an impedance of 1 + j2 № per phase. There are two loads connected in parallel. Load 1 is connected in wye, and the phase impedance is 4 + j2 2. Load 2 is connected in delta, and the phase impedance is 12 + j9 №. The current lab in the delta load is 16/45° A. Find the phase voltages of the source and the line currents. Write your values in polar form.
In abalanced Three Phase System The Source is balanced Wye With an abc – Phase Sequence and Vab = 215 450 Vrms The Load is balanced Wye paralle with ablaned delta . the phase impedance of Wye is 9 + j3 and the phase impedance of the delta is find the line impedance 1+ j0.8 2 find the line currents and phase currents in load .
A three-phase circuit is balanced. The source voltage for the a-phase has a magnitude of 100 volts, and you can assume the phase angle is a reference of 0 degrees. Write the phasor expressions with proper subscript notation for the source voltage for each leg of the three-phase source if it is in a positive phase sequence.
In the circuit in the figure; L1 load draws 15 kVA with lagging power factor 0.6. The L2 load draws 6 kVA with a leading power factor of 0.8. According to this; What is the value of the complex power for the L2 load?
Line Voltages at the terminal Pz:- The of abaancat Y conmected load is----- Each Phase of the load cousist of loL30 S2 Find the active s Reactive and somflex Power fer Phase then Find the total load. Var=12010, Powers for Heree phase
In a balanced Y-Y circuit shown in Figure 5, the magnitude of the phase voltage at the source is Vp = 2520 V (rms) and Van = 252020° V (rms). The load impedance is Zy = 135 + j55 Q per phase and the wire impedance is Zw=85 + j65 per phase. All the voltages and currents are in rms in this problem. (a) Find the phasors for line currents IA, IB, Ic in rms. (b) Find the load voltage VAN = IAZY. Also find VBN, and VCN. (c) Find the line voltages VAB, VBC, VCA at the load. (d) Find the complex power SL of the load. ZW ZY Van a A IA ZW ZY Vbn b В IB N ZW ZY Vcn IC Figure 5