In a balanced Y-A system the phase voltage is 11kV volts [maximum value], the impedance of each load element ZL [R,X] [12000, 2400] ohm. Each of the transmission wires has an equivalent impedance of [1000, -300] ohms. > Draw the circuit and label all elements. > Convert the delta to an equivalent star configuration. What is the RMS generator phase voltage? What is the RMS generator line voltage?

In a balanced Y-A system the phase voltage is 11kV volts [maximum value], the impedance of each load element ZL [R,X] [12000, 2400] ohm. Each of the transmission wires has an equivalent impedance of [1000, -300] ohms. > Draw the circuit and label all elements. > Convert the delta to an equivalent star configuration. What is the RMS generator phase voltage? What is the RMS generator line voltage?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.13MCQ

See similar textbooks

Similar questions

Problem 4- A large 3-phase industrial load draws 3.6 MVA at 0.85 power factor lagging from through a three- phase 12.47/7.2 kV 3-wire overhead distribution line. The phase conductor is #1 ACSR “Robin". Taking 3.6 MVA and 12.47 kV as base values, determine (a) The base impedance in (N) (b) The reactive power drawn by the load (p.u.) (c) The total current (p.u.) drawn from the power supply
2) The one-line diagram of a three-phase power system is as shown in Figure. Impedance are marked in per-unit on a 100-MVA, 400-kV base. The load at bus 2 is S2=15.93 MW - j33.4 Mvar, and at bus 3 is S3-77 MW + j14 Mvar. It is required to hold the voltage at bus 3 at ...L0 kV. Working in per-unit, determine the voltage at buses 2 and 1. (Please determine the voltage magnitude within the specified limits: 410-450 V. By considering the voltage magnitude value you determined yourself, solve the question.) V₁ j0.5 pu V₂ j0.4 pu S₂ Figure V3 S3
Question 3. A three-phase impedance load balanced D a connected load in parallel with a balanced ? connected load made of bonding. D each arm for the load ?D = 6 + 6? and ? each arm for the connected load It is given as ?? = 2 + 2?. ? the connected load ?? = 1? is earthed through the neutral impedance. To this impedance load, the symmetrical component voltages ?0 = 10∠60°, ?1 = 100∠0° and ?2 = Unbalanced phase-to-earth voltages ??, ?? and ?? of 15∠200° volts were applied. a) Draw the zero, positive and negative sequence circuits. b) Find the complex powers imparted to each component circuit.
Power in a three phase delta system with balanced load is equal to (Sqrt (3)) (VL) (IL) (p.f.) (Sqrt (3)) (Vph) (Iph) (p.f.) (Sqrt (3)) (VL) (Iph) (p.f.) O (Sqrt (3)) (Vph) (IL) (p.f.)
Power factor correction is usually done by adding _________ to the load circuit.Select the correct response:a. switchb. capacitorc. inductive loads
Shown are two buses connected via a transmission line. Connected to Bus 1 is a generator(modelled as a voltage source V1), and to Bus 2 is a generator( with Voltage V2) and a load. The line impedance Z = R + jX is not known. Three-phase load is forecasted as 100MW + 60MVar. Generator at Bus 2 is scheduled to deliver 40MW and its excitation is adjusted for the machine to deliver 55 MVar. Voltage at Bus 1 is 241 KV angle 10 deg, while voltage at bus is 230 kV; use V2 as the reference for all angles. 1. What is the current (RMS) in amperes drawn by the load connected to Bus 2? 2. How much real power (in MW) is delivered by the generator connected to Bus 1? 3. What is the total real power loss along the line, in percent of the load? 4. What is the X/R Ratio of the line impedance?
The one-line diagram of a three-phase power system is as shown in Figure. Impedance are marked in per-unit on a 100-MVA, 400-kV base. The load at bus 2 is S-15.93 MW-j33.4 Mvar, and at bus 3 is S3-77 MW+j14 Mvar. It is required to hold the voltage at bus 3 at...L0 kV. Working in per-unit, determine the voltage at buses 2 and 1. (Please determine the voltage magnitude within the specified limits: 410-450 V. By considering the voltage magnitude value you determined yourself, solve the question.) V₁ j0.5 pu V₂ j0.4 pu $₂ Figure V3
Q2) A 13.2-kV single-phase generator supplies power to a load through a transmission line. The load's impedance is Ztoad 500 236.87° ohm , and the transmission line's impedance is Zine = 60 253.1° ohm. To reduce transmission line losses to 0.0103 of its losses without using the transformers design and use two transformers T1 between the generator and the transmission line and T2 between the transmission line and the load.
The p.u. impedance value of an alternator corresponding to base values of 13.2 kV and 30 MVA is 0.2 p.u. Then the p.u. impedance value of an alternator for the new base values of 13.8 kV and 50 MVA is......
The one-line diagram of a power system is shown in the figure below. The 3-ph load is composed of three 4.8-0 capacitors in delta connection. The motor draws 50 MW, 0.6 power factor lagging at 20 kV. Use a base of 100 MVA, 20 kV in the generator circuit. Determine the generator and motor internal emfs and the transmission line current. Line M 3-ph Load The three-phase power and line-line ratings are given below: X = 24% 22 kV 22/110 kV G: 80 MVA T1:40 MVA X= 6.4% X= 42.35 Q X = 22.5% Line: 110 kV M: 68.85 MVA 20kV The three-phase ratings of the three-winding transformer T2 are: Y-connected 110 kV Primary: Secondary: 40 MVA, Y-connected 25 MVA, 22 kV Tertiary: A-connected 15 MVA, 4.4 kV Neglecting resistance, the leakage impedances are: 110 kV Zps = 9.6% Zpt = 7.2% Zst = 10% 40 MVA, 40 MVA, 25 MVA, 110 kV 22 kV %3D
The VSWR on an 50-Ohm transmission line is 5. The distance between successive voltageminima is 80 cm while the distance from the load to the first minimum is 30 cm. What are thereflection coefficient and load impedance
(a) A single phase, unity power factor load takes 70 A at 25 kV. Using a base voltage of 60 kV and base kilovolt amperes of 4050 kVA. Find the base current , base impedance , base power, and per unit current , per unit impedance, per unit power, per unit voltage of the load