If the unit mass of steel is 7850 kg/m3 and E = 200 x 103 MN/m2, find the total elongation of the rod given a steel rod having a cross-sectional area of 200 mm2 and a length of 120 m is suspended vertically from one end. It supports a tensile load of 18 kN at the lower end. O a. 56.77 mm O b. 59.68 mm 52.45 mm O d. 53.44 mm

If the unit mass of steel is 7850 kg/m3 and E = 200 x 103 MN/m2, find the total elongation of the rod given a steel rod having a cross-sectional area of 200 mm2 and a length of 120 m is suspended vertically from one end. It supports a tensile load of 18 kN at the lower end. O a. 56.77 mm O b. 59.68 mm 52.45 mm O d. 53.44 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

SITUATION III: The cross section of a tension member is shown below: Use Fy=275 MPa, Fu=400 MPa. 25 350 16 mm o 30 25 350 12. Compute for the gross area of the cross section. b. 29750 mm² d. 23000 mm? a. 28 000 mm? C. 23 490 mm? 13. Compute for the allowable tensile capacity due to yielding. a. 4698.00 kN C. 4610.78 kN b. 4654.39 kN d. 6706.59 kN 14. Compute for effective net area if shear lag factor is 0.90. Diameter of holes is 3mm more than that of bolts. a. 28 000 mm? C. 23 490 mm² b. 29750 mm? d. 23000 mm?
The initial compressive force of a steel column can be determined by Euler's buckling formula. The column has the following properties: A = 9484 mm2 Fy = 345 MPa Ix = 164 x 106 mm4 ly = 23 x 106 mm4 E = 200 GPa Proportional limit, f = 290 MPa %3D %3D The x-axis has an unbraced length of 10 m which is pinned athe top and fixed at the bottom with an k = 0.70. The y-axis has unbraced length of 5 m due to the bracing at the mid-height. Determine the factor of safety for the load shown with respect to buckling in the plane of the figure. Select the correct response: 1.24 1.18 1.41 4.373
O A rectangular strip 50×15mm deep of brass is placed on top of another strip 50×15mm deep of steel to form a beam of 50×30 mm deep cross-section. The beam is supported across a span of 100 cm. Determine the magnitude of a point load that may be placed at its midspan if (a) The strips separate and bend independently E steel = = 2×10 MPa, Ebras = 0.9×10 MPa, stress are o steel Permissible = 150 MPa and o = 100 MPa brass 100 cm
The two-dimensional framework consists of two bars CE and CD pinned at C, D and E; and a horizontal bar AB pinned at A as shown in the figure. Because of an assembly error the bar AB is slightly short of length ?. Determine the required axial force necessary to close the gap ?. All bars are made of steel and of the same cross-section and modulus of elasticity ? = 200 ??a
Determine the tensile force experience in WIRE 1 because of supporting the I - beam which has a weight of 1000 lbs. Tensile force in WIRE 1 is = Ib. Wire 2 Wire 1 W 6 ft- - e1.0 ft
A loaded pin-jointed truss is shown in the given figure. The force in member AC is (a) 10 √2 kN (Tensile) (c) zero 20 kN 10 kN C F A TITTT 3 m G D H 3 m K 3 m * ВУ ΟΤΙΣΣ (b) 10 √2 kN (Compressive) (d) 10 kN (Tensile) 3 m
Determine the value of a, c, strain in steel and ultimate moment strength of beam? E = 2*10 kg / cm E = 2*10°kg / cm f' = 250kg / cm? F = 4000kg / cm? 2 2 50 cm 55 cm 4φ20 30 ст
02 A cast-iron beam has a section as shown in the figure below. The beam is subjected to two concentrated loads of 3kN. The N.A is located at 35 mm from the bottom and that maximum flexural tensile stress =20 MPa. Determine the width (X) of the flange. 20mm 3kN 3kN 120mm 15m 35mm 20mm 2m 3m 2m
Problem. The truss shown in Figure 1 is made from seven members, each having a mass per unit length of 9 kg/m. determine the distance d (x) to where the lifting cole must be attached, so that the truss does not tip (otate) when it is lifted. Ignore the mass of the gusset plates at the joints and the thickness of the members can be neglected. 6m B Y A www 6m ~8-5m C 37 6m Figure 1 For Problem D
The beam is made from four boards nailed together as shown below. If the nails can each support a shear force of 500 N, determine their required spacing s' and s if the beam is subjected to a shear of V = 3.5 KN. 25 mm 250 mm 250 aut BE 40 mm 25 mm 25 mm 50 mx
A wide flange is used as a beam that is simply supported at its ends.The properties are shown.A = 19600 mm². by = 229 mmL = 1249 x10^4mm te=14 mm Tx = 25.4 mm tr = 24.9 mm ly = 49.5 x10^4mm d = 623 mm Ty = 50.5 mm If the beam is laterally supported at supports only, determine the allowable bending stress for a length of; 1. 2m 2. 4m 3. 6m 4. 8m
A steel column carries moment Mx = 11kN.m and My = 16.5 kN.m and an axial load of 220 KN. The steel section has the following properties:A = 7420 mm² ry = 50.4 mmSx = 693x10³ mm³ Sy = 186x10³ mm³K = 1.0 L = 6 mFy = 400 MPa E = 200000 MPaTx = 108 mm Cm = 0.85Axial compressive stress that would be permitted if axial force alone existed Fa = 72.54 MPa. Compressive bending stress that would be permitted if bending moment along the x-axis alone existed Fbx = 240MPa (0.60 Fy). Compressive bending stress that would be permitted if bending moment along the y-axis alone existed Fby = 300MPa (0.75 Fy). 1. Which of the following gives the axis compressive stress if axial load only existed. a. 30.45 MPa b. 27.82 MPa c. 28.46 MPa d. 29.65 MPa 2. Which of the following gives the bending stress if bending moment alone existed. a. 105 .48MPa b. 106.73 MPa c. 104.58 MPa d. 102.37 MPa 3. Using the…