Answer in 20 mins pls The bracket is supported by diameter = 18 mm diameter pins at A and B (the pin at A fits in the 0=35° slot inthe bracket). Assuming single shear and neglecting friction, determine the shear stresses in MPa in the pin IA if P-420Newtons. Use x= 620mm and y= 280mm 0y mmAB29Ꮎ■_xmm_P:

Answered: Image /qna-images/answer/25c59529-3c59-4931-bc81-76339f98ca69.jpg

he bracket is supported by diameter = 18 mm diameter pins at A and B (the pin at A fits in the 0-35° s me bracket). Assuming single shear and neglecting friction, determine the shear stresses in MPa in the if P=420Newtons. Use x= 620mm and y= 280mm

he bracket is supported by diameter = 18 mm diameter pins at A and B (the pin at A fits in the 0-35° s me bracket). Assuming single shear and neglecting friction, determine the shear stresses in MPa in the if P=420Newtons. Use x= 620mm and y= 280mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A solid steel bar of a diameter 1.2 in. is enclosed by a steel tube of outer diameter 1.8 in. and…

A: First we summarise the given data : Diameter of steel bar = 1.2 inches Outer diameter of steel tube…

Q: EI is constant (Assume EI= 1 kN-m^2) use moment area method 1.) determine the location of the…

Q: What is the settling velocity of a discrete particle in a wide body of water when the relevant…

A: Given data : Diameter of particle = 2 X 10-3 Specific gravity = 2.65 Water temperature = 20oC…

Q: where did you get the value 289 from the bending moment diagram?

Q: 8-147 In a hydroelectric power plant, water at 20°C is supplied to the turbine at a rate of 0.55…

Q: 5. In Correction in Taping what are the four Rules that we apply?

Q: 15.6 A slope is shown in Figure 15.50. If AC represents a trial failure plane, determine the factor…

Q: sketch the NFD, SFD, BMD, and deformed shape

A: A frame is given with roller support at A and fixed support at D. A hinge is also present at C. The…

Q: 15.1 Refer to the infinite slope shown in Figure 15.47. Given: ß = 25°, y = 17.8 kN/m³, ' = 28°, and…

Q: Yd= (Ysat-Yw) Gs Gs-1

Q: A Single rivet lop joint is to connect 12mm thick plates by providing 20mm dia. rivet at so mm…

Q: Design a rectangular section for the following beam considering the given loading. The weight of the…

A: Given fy= 60000 psi fc'= 4000 psi

Q: For a 2-D flow field, the stream function y 3 is given as y = (y²-x²). 2 The magnitude of discharge…

Q: : The T- beams sections shown in the figures below. f'c-28 Mpa, fy=420 Mpa. Calculate the design…

Q: A cable of span 120 m and dip 10 m carries a load of 6 kN/m of horizontal span. The maximum tension…

A: Given : Span = 120 m dip = 10 m Load carried by cable = 6 kN/m Determine the max. tension in the…

Q: Compute the moments of inertia with respect to the X-X and Y-Y centroidal axes for the following…

A: Given: Required Moment of inertia about centroidal X and Y axes

Q: Integration mine the deflection at midspan between A and B by

Q: Does a positive presumptive test indicate that water is potable?

A: A screening test called the presumptive test is used to check a water sample for the existence of…

Q: 2. Determine the centroid and moment of inertia along x-axis of the given built- up members (Mertric…

A: To find the centroid and Moment of Inertia of the given area about the x axis (Centroidal Axis).

Q: *If the required weight of coarse aggregate for mix design is 2000 lbs per cubic yard of PCC,…

A: Reference : ACI 318 mix design code Given : Weight of coarse aggregate Specific gravity To determine…

Q: The motor winds in the cable with a constant acceleration, such that the 20-kg crate moves a…

Q: 1. Determine the centroid and moment of inertia along x-axis of the given American standard…

Q: 8.58 A 15° wedge is forced into a saw cut to prevent binding of the circu- lar saw. The coefficient…

Q: The structural system below using rotational spring + hinge support at joint A and rotational spring…

A: reestablishing force = applied second or force reestablishing force 'T1 = 2Kphi2 +Kphi1' applied…

Q: determining characteristics of pavement. The propagation of electromagnetic waves through

Q: The beam ABC is subjected to a point load at the middle of segment AB and a uniformly distributed…

A: Data given Find : Equation of elastic curve for segment AB

Q: : The T- beams sections shown in the figures below. f'c-28 Mpa, fy-420 Mpa. Calculate the design…

Q: 14.1 What is the meaning of the acronyms CMU, URM, UMB?

A: To find : Meaning of acronyms CMU, URM and UMB

Q: Problem 8.1. On a given day, the following meteorological and surface measurements were collected at…

A: On a given day, the following meteorological and surface measurements were collected at noon from a…

Q: A wide rectangular channel laid on a slope of 0.009 has a Manning's roughness coefficient n = 0.014.…

Q: Q2: Design the rectangular reinforced concrete beam shown in the figure to carry service loads of…

A: Given: DL = 10 kN/m LL = 15 kN/m L = 6 m Assume; fc = 25 MPa fy = 400 MPa

Q: Q-An RC square column of size 600 mm is constructed to carry an unfactored load of 3000 kN. The ends…

A: Given- RC square column, Size 600 mm, Unfactored load P=3000 kN, M-25 concrete and Fe-415 steel,…

Q: Using Superposition method, determine the reaction at each support of the beam. 15KN/m 6 kn/m A +177…

Q: The plan area of an old survey plotted to a scale of 10 m to 1 cm presently measures 82.5 cm². It is…

Q: (a) List at least five examples of a discrete variable and five continuous variables.

A: "Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: Q- A rectangular open channel of 6 m width is carrying a discharge of 20 m³/s. Consider the…

A: Open Channel: An open channel is a canal in which the water flows along the free surface. The flow…

Q: The plate shown is fastened to the fixed member by five 10-mm-diameter rivets. Compute the value of…

Q: Q- A rectangular open channel of 6 m width is carrying a discharge of 20 m³/s. Consider the…

Q: 60N L 30 Q 3m 40° 150N A 90N SON P 4. Which of the following force diagrams shows correctly the…

Q: The recommended velocity of flow in the discharge line of an oil hydraulic system is in the range of…

A: Given Data - Velocity of Flow (v) = 8 to 25 ft/sec Pump capacity (Q) = 30 gal/min Find -…

Q: Determine the RL of the top of a transmission tower from the following observations. Also determine…

Q: are

A: In the question we are asked about the civil engineering we will discuss in the next three steps…

Q: QUESTION 5: Determine the state of stress that the loading produces at points C and D in the figure…

Q: As part of a stream restoration project, a design engineer would like to create a nice little area…

A: According to given Data A 50-foot-wide stream by adding a root wads on one side and a large rock on…

Q: A basin is divided by 1-h isochrones into four sub-areas of size 200, 250, 350 and 170 hectares…

Q: 6. In a longitudinal profile, which is rotated at center lane. The height of the outer lane is 0.80…

A: given: height of outer lane (h) = 0.8m superelevation (e) = 0.08 To find : width of road (w)

Q: Two pegs A and B were fixed on opposite banks of a 50 m wide river. The level was set up at A and…

Q: : A T- beam section shown in the figure below. f'c=28 Mpa, fy=420 Mpa. Calculate the design moment…

A: Given Width of flange ,bf = 800 mm Width of web, bw = 400 mm

Q: Group C: Design a concrete mix to implement a Mass concrete (exposed to sever conditions moisture…

A: Given: Design compressive strength = 25 MPa Standard deviation = 4 Cement = sulphate resisting…

Q: 15 ft 2.5 k/ft B A El= constant 15 ft 50 k-ft с

Concept explainers

Design criteria for structural loading

The different loads such as loads due to self-weight (dead load) and external loads such as live load, wind loads, seismic load, snow load, and other loads and load combinations that influence the design of a building are called structural loading. The nature of the applied load differs from changes in the location, design, and type of materials used. The design criteria require that structures must be designed and constructed to be able to withstand all load types that are expected to act upon the structure and render its usage for the designated purpose. The structural members such as beams, slabs, columns, and foundations help the structure to withstand the applied load. There are different institutes such as ASCE and ACI that provide building design codes to assure minimum safety requirements and quality of the structures.

Question

Answer in 20 mins pls

The bracket is supported by diameter = 18 mm diameter pins at A and B (the pin at A fits in the 0=35° slot in
the bracket). Assuming single shear and neglecting friction, determine the shear stresses in MPa in the pin I
A if P-420Newtons. Use x= 620mm and y= 280mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The bell-crank mechanism is in equilibrium for an applied load of F1 = 11 kN applied at A. Assume a = 250mm, b = 100mm, c = 90mm, and θ = 40°. Pin B is in a double-shear connection and has a diameter of 29 mm. The bell crank has a thickness of 31 mm. Determine the shear stress in pin B and bearing stress in the bell crank at B. Express your answer in MPa rounded to the nearest hundredths.
A truss is loaded as shown in the figure. The cross- sectional area of each member is 500 mm^2. Hint: Use method of section in getting the axial forces. Use the guide cutting sections. L-6 m+6m- N 25 kN 8 m 50 kN - a 8 m 50 kN 8 m 50 kN 8 m B. 9. Find the axial stress in member HK O 35.34 MPa O 31.12 MPa O 33.34 MPa O 37.12 MPa Question 10 10. Find the axial stress in member HJ. O 125 MPa О 123 МPа O 127 MPa O 129 MPa
7. (c) A load P of 5000 Kg on the crank pin of the crank shaft as shown in figure is required to turn the shaft at constant speed. The crank shaft is made of ductile steel having yield strength of 2800 Kg/cm2 as determined in simple tensile test. Calculate the diameter of the shaft based on a factor of safety of 2.5. Use maximum shear stress theory. Consider section m-n as critical section. 'm 20cm P 15cm
Two 10-mm thick plate members are to be connected using straps of the same thickness and 12-mm diameter rivets as shown in the figure. Determine the average shear stress in the rivets if the maximum tensile stress on the plate members due to load "P" is 24 MPa. The members are 50-mm wide. Assuming all the rivets fill the holes. Strap Plate Member Plate P P.
The five 20mm-diameter rivets fasten the plate as shown in the figure to the fixed member. a). Determine the value of the load P so that the average stress of any rivet does not exceed 80MPa.b). What additional clockwise torque can be applied before the shearing stress exceeds 90MPa
The plate shown is fastened to the fixed member by seven 12-mm diameter rivets. Compute the polar moment of inertia, J. Determine the value of the loads P so that the maximum shearing stress in any rivet does not exceed 75 MPa. If P = 8000 N, what is the minimum shearing stress developed in the rivet.
The lap joint shown is fastened by 6 − 20mm diameter rivets. Assuming that ? = 200??, determine (a) the shearing stress in each rivet, (b) the bearing stress in each plate 25mm thick and 100mm wide. Assume that the axial load ? is distributed equally among the 6 rivets, and the diameter of hole is 22mm.
-1.2 m- -1.2 m- OB A 0.9 m P D Beam AB Bolt at C Strut CD Figure 2 Figure 2 shows a rigid beam ACB supported by a strut CD. A load P=7.5 kN is applied at B. Show that the strut is in compression. Knowing that the allowable shear stress for bolt at C is 85 MPa, check if the bolt is safe to Determine the allowable maximum compressive force in strut based on be used. allowable shear stress in bolt at C.
A structural member is fabricated with the cross section show below and is eccentrically loaded with F. - 26--| F 2t F b. Use G = 77.2 GPa. If I = 4 m, t= 3 mm, b = 80 mm, and F = 121 kN, Determine the maximum shear stress due to torsion. Select the correct response: 168.056 MPa 215.278 MPa 155.556 MPa of 133.333 MPa 22
The lap joint shown is fastened by 6 − 20mm diameterrivets. Assuming that P = 200KN, determine (a) theshearing stress in each rivet, (b) the bearing stress ineach plate 25mm thick and 100mm wide. Assume that the axial load P is distributed equally among the 6rivets, and the diameter of hole is 22mm.
A cantilevered structural member is fabricated with the cross section shown below and is eccentrically loaded with F. - 26- F 2t F tt Use G = 77.2 GPa. If I = 4 m, t = 3 mm, b = 80 mm, and F = 112 kN, %3D Determine the maximum shear stress due to torsion. Select the correct response: 133.333 MPa 215.278 MPa 168.056 MPa 155.556 MPa
06 ameter against Es P are Q13. A torque T = 5 kN.m is applied to a hollow shaft having the cross section shown. Neglecting the effect of stress concentrations, determine the shearing stress at points a and b. welded owable nissible 10 mm 6pm 125 mm 6 mm 10 mm 75mm Q14. A hollow member having the cross section