HCM-6 At the design speed Vo Dan's car can go around a banked curve of radius 150M and banking angle of 10.0° without any friction force. The car is shown as viewed from behind in the figure below. R=150m 10.0° a) Use the figure above to draw the free body diagram for the car. Also show on the FBD the direction of the car's acceleration and show coordinate axis directions. b) Write down newtons's second law in component form for the car. Use NO numbers for this part. c) Use your equations from step b) to find the design speed Vo.

HCM-6 At the design speed Vo Dan's car can go around a banked curve of radius 150M and banking angle of 10.0° without any friction force. The car is shown as viewed from behind in the figure below. R=150m 10.0° a) Use the figure above to draw the free body diagram for the car. Also show on the FBD the direction of the car's acceleration and show coordinate axis directions. b) Write down newtons's second law in component form for the car. Use NO numbers for this part. c) Use your equations from step b) to find the design speed Vo.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q5-A) A rope pulls the block up the ramp as shown in the figure. Find the following: 1. Draw a free body diagram for the block. a = 4.3 m/s? T = 2. Write the equation that sums the forces on the block that are parallel to the ramp. 3. Write the equation that sums the forces on the block that are perpendicular to the ramp. 4. What is the acceleration of the block perpendicular to the ramp? 5. What is the friction force? k = 0.45 6.0 kg 0= 30° 6. What is the tension force?
If VA = 96.2 i in/sec in the figure below, find w2, the angular speed of bar B2. By 12 in. Bs B8 in. i -10 in. To calculate the angular speeds of the two bars B2 and B3, you need to use the two point formula: 1) fırst on rigid body B2 to calculate the velocity of point B (since you know velocity at point A) 2) then on rigid body B3 to calculate the velocity of point D (since you know velocity at point B) 3) Note that the velocity at point D has to be zero. Thus the two components of the velocity are zero giving you two equations to solve for the two unknown angular velocities. Figure is from "Engineering Mechanic An Introduction to Dynamics", McGill and King.
2- The swinging motion of the upper arm may be described as the follows; 0= 10 sin 0.06 t where 0 is the relative angle between the upper arm and the trunk in sagittal plane and the time t ranged from 0 to 60 sec .plot angular position,velocity and acceleration and find the maximum acceleration. Biomechanics Use Graphical method to draw
Unlike the common V6 engine, Subaru engines contain pistons that are horizontally opposed (see Wikipedia for more info). Luckily for us, this also makes for an interesting dynamics problem! At the instant shown, the crank arm's angular velocity is waB = 2,000 rpm (rotating clockwise) and the angle 0 = 40° with respect to the horizontal. Length of bar AB is r1 = 3 in. and the length of bar BD is r2 = 8 in. a) Clearly define coordinate systems for each link and write transformation arrays for each. b) Compute the velocity of point B in ft/s. Express your answer in rectangular coordinates. [Ans. to Check: 33.66 i– 40.11 j ft/sec] c) Determine the magnitude of the speed of the piston P in ft/s. Note: all answers should be positive since we only want to know the magnitude of the speed, not the direction (the piston can only move in the horizontal direction). [Ans. to Check: 43.6 ft/s] r2 10 B
Problem Solving: ) A car is fraveling at the speed Vo on a Tevel road. After the brakes arc applicd at t- 0, the motion can be approximated by x where x is the distance traveled in mcters and t is the time in scconds. Find: (a) Find the value of Vo (6) Find the distance reguired for the car to straight, %3D 2. --t+ 17t 100 stop.
3) Rotational Kinetics VG = 20 ft/s 0.5 ft A The 20 Ib ball is given an initial backspin w = 10rad/s. Determine the velocity of the center of the ball after the ball stops slipping if µx = 0.3. Consider the following procedure a) Draw a FBD of the ball including a kinetic friction force (the ball is slipping) b) Write Newton's second laws for translation and rotation c) Solve for the acceleration and angular acceleration of the ball d) Find the velocity and angular velocity as functions of time e) Looking at those equations, consider when the ball would stop slipping 3
In the arrangement in the figure, the reels 'a 'and 'b' are pulled at VA m/s and VB =12 m/s. since there is no friction between the block and the surfaces; a) find the velocity and acceleration of block c when roller a moves 60mm to the left and roller b moves 90mm to the right b) find the rope force acting on the cable. (a=30°)
A Tram used in San Francisco has a mass of 300 tons has a tractive resistance of 45000 N as shown in the figure below.a) Calculate the total force required to accelerate the tram uniformly form 18km/h for one minute over a distance of 750 meters up an incline 1 in 150.b) What is the maximum power developed by the locomotive under those conditions?c) Calculate the angular velocity of the wheels under conditions of maximum power is found to be 191 rev/min. What toque is the locomotive developing and what is the diameter of the driving wheels?NB: Show a detailed space diagram in your solution (a
QUESTION 4 B 2.3 m 4.5 m 0 = 28° 41° @Bc= 3.6 rad's' C Fig. 4 For the rigid body shown in Fig. 4: a) Identify the type of rigid-body motion for slider A, link AB, and link BC. Define your positive direction for translation and rotation. b) By using the vector method, calculate the magnitude of velocity at point B, magnitude of velocity at point A and angular velocity of the link AB. Show detail calculation including separate kinematic diagram for each link.
In the mechanism shown below, points E and B have the same vertical coordinate. Find the velocities of points B. C, and D of the double-slider mechanism shown in the figure if Crank 2 rotates at 42 rad/s CCW. And all forces acting. D 6. EA - 0.55" AB - 2.5" AC - 1.0" CB = 1.75" CD - 2.05" 0.75"- 4 3 60 A
5. The figure shows a scaled kinematic diagram of a linkage. The velocity magnitude of joint A is 10 in/s and its direction is as shown in the figure. Find the velocity magnitude of joint B using the instant center method. AC= 1.95" AD = 2.0" V42 DE = 1.1" BD = 0.9" BE = 1.9" A B 3 2 C (3.35", 0.3") E Rectangular Snip 1.0"-
The pulley shown rotates at 10rad/s clockwise. Find the velocity of weight A (use up as + for the sign convention). You must show your work and include a diagram Hint: The distance between the fixed pulley and bottom ground is a constant Upload