Home work saPiJ A sevies Circuit.consists of three resistors R=25k,R2 = 65k2,R3=80 k.1f the voltage drop across Ris lov, calculata thesa) Supply voltage) Valtage drop across Rg9 power dissipatd by R2%3D(Ans: 68 V, 32 V, l04 mw).

Answered: Image /qna-images/answer/45501025-84dd-4ef1-96fc-68805616edac.jpg

Hame Work se PiJ A series Circuit consists of three resistors R=25k R2 = 65ksn, R3=80 k.17 the roltage dvop across R is lov, calculate the a) Sayply valtage ) Yaltage drop across Rg 9 power dissipated by R2 %3D !! (Ans: 68 V, 32 V, lo44 mm).

Hame Work se PiJ A series Circuit consists of three resistors R=25k R2 = 65ksn, R3=80 k.17 the roltage dvop across R is lov, calculate the a) Sayply valtage ) Yaltage drop across Rg 9 power dissipated by R2 %3D !! (Ans: 68 V, 32 V, lo44 mm).

University Physics Volume 2

18th Edition

ISBN:9781938168161

Author:OpenStax

Publisher:OpenStax

Chapter10: Direct-current Circuits

Section: Chapter Questions

Problem 69AP: Consider the circuit below. The battery has an emf of = 30.00 V and an internal resistance of r =...

See similar textbooks

Similar questions

An ECG monitor must have an KC time constant lessthan 1.00102s to be able to measure variations involtage oversmall time intervals, (a) If the resistance of the circuit (duemostly to that of the patient's chest) is 1.00kTwhat is the maximum capacitance of the circuit?(b) Would It be difficult in practice to limit the capacitance to less than the value found in (a)?
A homemade capacitor is constructed of 2 sheets of aluminum foil with an area of 2.00 square meters, separated by paper, 0.05 mm thick, of the same area and a dielectric constant of 3.7. The homemade capacitor is connected in series with a 100,00- resistor, a switch, and a 6.00-V voltage source, (a) What is the RC time constant of the circuit? (b) What is the initial current through the circuit, when the switch is closed? (c) How long does it take the current to reach one third of its initial value?
Figure 21.55 shows how a bleeder resistor is used to discharge a capacitor after an electronic device is shut off allowing a person to work on the electronics with less risk of shock, (a) What is the time constant? (b) How long will it take to reduce the voltage on the capacitor to 0.250% (5% of 5%) of its full value once discharge begins? (c) If the capacitor is charged to a voltage V0through a 100-O resistance, calculate the time it takes to rise to 0.865V0(This is about two time constants.)
A circuit contains a D-cell battery, a switch, a 20- resistor, and three 20-mF capacitors. The capacitors are connected in parallel, and the parallel connection of capacitors are connected in series with the switch, the resistor and the battery, (a) What is die equivalent capacitance of the circuit? (b) What is the KC time constant? (c) How long before the current decreases to 50% of the initial value once the switch is closed?
In Figure 21.41. does the graph indicate the time constant is shorter for discharging than for charging? Would you expect ionized gas to have low resistance? How would you adjust R to get a longer time between flashes? Would adjusting R affect the discharge time?
Integrated Concepts A 12.0-V emf automobile battery has a terminal voltage of 16.0 V when being charged by a current of 10.0 A. (a) What is the battery’s internal resistance? (b) What power is dissipated inside the battery? (c) At what rate (in °C/min ) will its temperature increase if its mass is 20.0 kg and it has a specific heat of 0.300 kcal/kg. °C, assuming no heat escapes?
A typical cell phone consumes an average of about 1.00 W of electrical power and operates on 3.80 V. (a) What average current does the phone draw from its battery? (b) Calculate the energy stored in a fully charged battery if the phone requires charging after 5.00 hours of use.
Figure P18.26 shows a voltage divider, a circuit used to obtain a desired voltage Vout from a source voltage . Determine the required value of R2 if = 5.00 V, Vout = 1.50 V and R1 = 1.00 103 (Hint: Use Kirchhoff's loop rule, substituting Vout = IR2, to find the current. Then solve Ohms law for R2. Figure P18.26
Figure P18.26 shows a voltage divider, a circuit used to obtain a desired voltage Vout from a source voltage . Determine the required value of R2 if = 5.00 V, Vout = 1.50 V and R1 = 1.00 103 (Hint: Use Kirchhoff's loop rule, substituting Vout = IR2, to find the current. Then solve Ohms law for R2. Figure P18.26
Consider the circuit below. The battery has an emf of = 30.00 V and an internal resistance of r = 1,00 . (a) Find the equivalent resistance of the circuit and the current out of the battery. (b) Find the current through each resistor, (c) Find die potential drop across each resistor, (d) Find the power dissipated by each resistor, (e) Find the total power supplied by the batteries.
Differential Equations: Electric Circuits When a resistance R (ohms) and a capacitance C (farads) are connected in series with an emf E (volts), the current I (amperes) is given by the equation: dE 1 R- +-I = dtC dI C dt If R = 1000 ohms, C = 5x10-4farad.and I t = 1 second and E = 100 volts. a. 1.35 amperes b. 2.35 amperes c. 3.35 amperes d. 4.35 amperes 10 amperes for t = 0, find the current for
Given the equation, V = Voe RC. , what size of resistor would be required to dirop the voltage on a 120mFapacitor to its original valtage in 5 min? Select one Oa R= 1.5 k2 Ob. R= 1.8 kS2 O. R= 1.7 k S O d. R= 1.6 k S2