Explain each safety rules.See the pictures below.. GENERAL SAFETY RULES FOR ELECTRICITY AND ELECTRONICSSafe practices will protect you and your fellow workers. Study the following rules.Discuss them with others, and ask your instructor about any that you do not understand.1. Do not work when you are tired or taking medicine that makes you drowsy.2. Do not work in poor light.3. Do not work in damp areas or with wet shoes or clothing.4. Use approved tools, equipment, and protective devices.5. Avoid wearing rings, bracelets, and similar metal items when working around exposedelectric circuits.6. Never assume that a circuit is off. Double check it with an instrument that you are sureis operational.7. Some situations require a "buddy system" to guarantee that power will not be turnedon while a technician is still working on a circuit.8. Never tamper with or try to override safety devices such as an interlock (a type of switchthat automatically removes power when a door is opened or a panel is removed).9. Keep tools and test equipment clean and in good working condition. Replace insulatedprobes and leads at the first sign of deterioration.10. Some devices, such as capacitors, can store a lethal charge. They may store this chargefor long periods of time. You must be certain these devices are discharged beforeworking around them.

We are authorized to answer three subparts at a time, since you have not mentioned which part you…

GENERAL SAFETY RULES FOR ELECTRICITY AND ELECTRONICS Safe practices will protect you and your fellow workers. Study the following rules. Discuss them with others, and ask your instructor about any that you do not understand. 1. Do not work when you are tired or taking medicine that makes you drowsy. 2. Do not work in poor light. 3. Do not work in damp areas or with wet shoes or clothing.

GENERAL SAFETY RULES FOR ELECTRICITY AND ELECTRONICS Safe practices will protect you and your fellow workers. Study the following rules. Discuss them with others, and ask your instructor about any that you do not understand. 1. Do not work when you are tired or taking medicine that makes you drowsy. 2. Do not work in poor light. 3. Do not work in damp areas or with wet shoes or clothing.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

ChapterS: Safety, Basic Electricity And Ohm's Law

Section: Chapter Questions

Problem 1RQ: What is the most important rule of electrical safety?

See similar textbooks

Similar questions

one of the following is a disadvantages of the power electronics system. a. installation b. harmonics c. efficient d. reliability
Module 10 Section Review 3.0.0.png Additional Resources Electronics Fundamentals: Circuits, Devices, and Applications, Principles of Electric Circuits, Thomas L. Floyd. New York: Prent 3.0.0 Section Review 1. The letter designation SL on an electrical draw- ing indicates a 4. A a. a. limit switch b. low-voltage switch c. load switch d. light switch b. C. d. 2. Existing power lines on an electrical site plan may be indicated by the letter 5. In t safe a. E b. I a. b. 2 С. Р d. V C. 2 d. 2: 3. The specific types of luminaires required in an installation can be found on the a. power plan b. electrical site plan c. schematic diagram d. lighting fixture schedule P Search for anything
SUBJECT: ELECTRICAL MACHINES 1 FOR ELECTRICAL ENGINEERS TOPIC: DC GENERATOR AND DC MOTOR NOTE: ANSWER THE QUESTIONS AND COMPLETE THE ANSWER WITH FULL COMPLETE DIAGRAM AND EXPLANATION IN TYPEWRITTEN. MAKE SURE THAT YOURE ANSWER IS CORRECT, I WILL RATE HIGHLY IF THE ANSWER IS CORRECT! THANK YOU Instruction: answer and explain the following items below. 1. Process of energy conversion & Power Stages 2. Diagram ➤ Energy Conversion in DC Machines o DC Generator o DC Motor ➤ Power Stages o DC Generator o DC Motor
5 a) Discuss Electricity power generation and distribution to residential properties. b) with diagrams explain how a Distribution Board is wired to provide electricity to a residential property. c) Explain the following materials and Accessories. i. Male and female bushings. ii male and female adaptors iii. Couplings. iv. Wire/cable sizes and their us
Centennial College - School of Engineering Technology - Toronto ELECTRONICS SHOP PRACTICES CHAPTER 7: SOLDERING TECHNIQUES 7,5 QUESTIONS 1. Which tools will you need for soldering? 2. What type of solder do we call the Eutectic Solder? 3. If the temperature is too high, the is bellow required, the solder joint will appear cold and silvery and will be of the contact may occur and circuit will not work. If the 4. A long and sharp will be of little use when soldering wires or 5. The iron should have a tip to prevent and should have a wattage rating of to Watts. 6. When soldering, apply heat solder will to both, the component lead and much more readily over the copper pad so that the 7. Keep the soldering iron tip and working surfaces wipe only before using and immediately. 8. Do not solder from a heated tip before off the iron. alternate applying the surface. 9. If tips become and wiping to being used. 10. Periodically. the tip from your tool and with a suitable cleaner for your skills.…
Which of the following statements about fluorescent lamps is correct? a. Fluorescent lamps have positive electrical resistance, meaning that the resistance increases with the flow of current. b. Fluorescent lamps can be operated without a ballast because they self-limit their current consumption. c. The ballast in fluorescent and HID lamps serves as a transformer to boost voltage and a choke to limit the flow of current. d. Fluorescent lamps don’t need a higher voltage to initiate the electric arc. e. Once an arc is struck in a fluorescent lamp, the ionized mercury vapor reduces its conductivity, limiting the flow of current.
9. When making a high energy measurement: a. Attach the meter to the energized line first, then to ground. b. Attach the meter to ground first, then to the energized line. c. Attach both meter leads concurrently. d. Remove power completely, attach the meter, then restore power.
The amount of heat generated in a conductor or other electrical equipment is a matter of how much current flows and? A. The type of insulation b. For how far c. For how long d. The ocpd
2. Give any sample of electrical components or processes that DC machinery Application plays an important role. Draw the diagram and label each part.
Why PMMC Voltmeters can not be used to measure higher voltages directly? a. because the size of the coils will raise b. because the coils will not be present at all c. because of the lesser current ratings. d. because of the lesser size problems
Describe what a maintenance work order in electrical engineering should contain. Don't copy it from other sources..
5.a. The labor performed when you extend an existing electrical system is called A. old work. B. repair work. C. troubleshooting D. faultfinding. 5.b. The basement in an existing building has concrete walls, a concrete floor, and a concrete ceiling. From this information, you know that receptacles, lamp fixtures, and switches A. can't be installed in this basement as there is no way to ground the circuit. B. won't require ground-circuit protection because concrete insulates the occupants from ground. C. can be installed in the basement and circuit wiring enclosed in a surface raceway system. D. can only be installed if they're connected with armored cable.