+VccFor the power amplifier of figure, ifC1 = C2 = 100 µF, R, = R2 = R3 =100 A, RL = 16 N, Vcc = 12 V,V:(rms) = 8 V;a) Calculate P,(ac) (the amplifierhas, ideally, a voltage gain of unity)b) Calculate P,(dc)c) Calculate efficiency % 7d) Is the efficiency maximum?Why?C2e) Find power dissipated by bothoutput transistors.-Vc

Amplifier is an electronic device whose output is amplified version of the input signal. Thee…

For the power amplifier of figure, if C = C2 = 100 µF, R1 = R2 = R3 = 100 1, R2 = 16 N, Vcc = 12 V, V(rms) = 8 V; a) Calculate P,(ac) (the amplifier has, ideally, a voltage gain of unity) V b) Calculate P,(de) RL c) Calculate efficiency % 7 d) Is the efficiency maximum? Why? e) Find power dissipated by both output transistors. -Vec

For the power amplifier of figure, if C = C2 = 100 µF, R1 = R2 = R3 = 100 1, R2 = 16 N, Vcc = 12 V, V(rms) = 8 V; a) Calculate P,(ac) (the amplifier has, ideally, a voltage gain of unity) V b) Calculate P,(de) RL c) Calculate efficiency % 7 d) Is the efficiency maximum? Why? e) Find power dissipated by both output transistors. -Vec

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Build an AC/DC dual power supply circuit that draws a 60Vp-p sinusoidal voltage, to provide a dc output voltage of +15 V. Full analysis of voltages and currents should be included. What modifications would you recommend to draw more current while maintaining same output voltage?
Example: For the circuit shown in Figure below find; a) The value of R1 for maximum power transfer. b) The maximum output power. (Ans. 9 Q, 13.44W) R R. 22 a R2 12 Q E R 12V 2A Solution:
Q#2 (A) The circuit shown in figure below has a Ves(oft) = -4V. Assume that you increase the supply voltage VoD, beginning at zero until the ammeter reaches a steady value. What does the voltmeter read at this point? Rp 4.7 kn VDp Figure (B) Assume for a particle JFET, Ioss=12mA and Ves(off)= -5V? a. What is lp Wwhen Vas-0V? b. What is lo when Vas=Vas(off)? c. If Vcs is increased from -5V to -2V, does lo increase or decrease?
The circuit shown in the following in figure has: VIN= 10 V, Vz = 7.2 V@ Iz-40 mA, Izk =2 mA, IzM= 100 mA and Zz-5 2. Determine a) Maximum output voltage. b) Minimum output voltage. c) The percentage load regulation. d) The minimum permissible load resistor value. c) The maximum permissible load resistor value. R 2211 VIS
the current. (c) Determine the power absorbed by the load. Q3) Design a buck-boost converter to supply a load of 75 Wat 50 V from a 40-V source. The output ripple must be no more than 1 percent. Specify the duty ratio, switching frequency, inductor size, and capacitor size.
A. For the circuit diagram shown below, determine and sketch the output voltage (Vout). 1_ohm GaAs 1 ohm 1_ohm Ge Si A 1_ohm. 6_Vpeak w. Vout)
A single-phase full-wave converter in the figure below is supplied with a 120-V, 60-Hz source. The load is highly inductive and the load current is continuous and free of ripples. The electromotive force is neglected (E = 0) and the resistance has a value of R = 10 2. The average output voltage is 85% of the maximum possible average output voltage. The delay angle would be equal to: Select one: 81.8° O b. 31.8° O c 67.8° O d. 51.8° AT₁ AT, R L +7=4₂ W
For amplifier shown in Figure E1, determine Vout and V,. 10 mV rms R 560 k 1.5 kl) Figure E1
Q2: Design a boost converter to provide an output of 18 V from a 12-V source. The load is 20 W. The output voltage ripple must be less than 0.5% and inductor current ripple less than 30%. The switching frequency is 25 kHz. Specify the duty ratio, the inductor size, and the capacitor size Assume ideal components.
A high voltage engineer cascades 6 stages of a voltage doubler circuit to analyze effectiveness of doing so. Each capacitor in the circuit is 15 nF, of the input Asupply is 100 kv at Frequency 100 Hz. . so this voltages not enough with one moudle.So How much moudle can be in cascades fashion if the load current is 1 mA.
= Assume Vcc = 18V, L₁= 5nH, C3 = 1000pF, total current drain of 1.5mA, V, 15Vp-p, Q = 100 Vin C₁₂ R₁₂ 10 ΚΩ Vcc RL · 10 ΚΩ 1. If Vin = 2V RMS: a. Calculate the peak-to-peak input voltage at the base. b. Calculate the DC voltage measured at the base. c. Draw the AC voltage at the base as it would be seen on the oscilloscope with appropriate detail.
2. A 12 phase balanced midpoint rectifier provides 200A at 200V to the load resistance. The load and filter are shown below (R in parallel with C, which is in series with the filtering inductor). Each source operates at 60Hz and has peak voltage of 340V=Vo, for example vi(t) 340cos(2p60t), and the other 11 sources out of phase (balanced) but with the same amplitude. (m=12) = a) What inductance value L that is needed to keep the peak-to-peak current ripple below ±15%? b) What is the capacitance value C that is needed to keep the peak-to-peak ripple below ±5% for this inductance value in part a)? #1 C V₁ = Vocos(wint) #2 * V2₂= Vocos(wint - #3 0000 *° * V3 = V₁ cos(wint - : Vm= V₁ cos(wint-(m-1)) #m + va(t) R