For the cross section shown, Analyze by using the concepts of shear stress, shear flow and shear center in thin walled open section beams: (a) draw the shear stress diagram and determine shear flow values due to the vertical shear force V; and (b) Calculate the distance e locating the shear center 0. Assume that the thickness of the section is constant which is t= 2.5mm. Note: The thickness t is very small as compared to the other dimensions; therefore consider center-line dimensions for the calculations as mentioned in the figure. - 80 mm V= [1500 +(100×R)] N NA 200 mm 2.5 mm

For the cross section shown, Analyze by using the concepts of shear stress, shear flow and shear center in thin walled open section beams: (a) draw the shear stress diagram and determine shear flow values due to the vertical shear force V; and (b) Calculate the distance e locating the shear center 0. Assume that the thickness of the section is constant which is t= 2.5mm. Note: The thickness t is very small as compared to the other dimensions; therefore consider center-line dimensions for the calculations as mentioned in the figure. - 80 mm V= [1500 +(100×R)] N NA 200 mm 2.5 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A thin polymer plate PQR is deformed so that corner Q is displaced downward 1.3 mm to new position Q', as shown in. Determine the shear strain at Q' associated with the two edges (PQ and QR). Assume a = 64 mm, b = 100 mm, c = 80 mm, and Δ = 1.3 mm.
Question 2. The square plate ABCD is deformed into the shape shown by the dashed lines. If DC has a normal strain Ex = 0.005, DA has a normal strain ey = 0.004 at D, Yxy = 0.01rad determine the shear strain at point E with respect to the x' and y' axes. 600 mm- 600 mm E D
Question 2. The square plate ABCD is deformed into the shape shown by the dashed lines. If DC has a normal strain 6x = 0.005, DA has a normal strain e, = 0.004 at D, y = 0.01rad determine the shear strain at point E with respect to the x and y' axes. 600 mm 600 mm
Mohr's circie is shown for a point in a physical object that is subjected to plane stress. Each grid square is 640 psi in size. (a) Determine the stresses o, 0, and the magnitude of Tyand show them on a stress element. (b) Determine the principal stresses and the magnitude of the maximum in-plane shear stress acting at the point and show these stresses on an appropriate sketch (eg, see Figure 12.15 or Figure 12.16). Answer: (a) o.. psi dy- Dsi psi psi psi Tmax inplane psi
The rectangular plate is deformed into the shape shown by the dashed lines. Calculate the average normal strain along diagonal AC. and The average shear strain at corner A relative to the x,y axes.
The figure shows the stress condition of an I-section beam at point A. With the Mohr circle method; 1-)Calculate the principal stresses, location and angle. 2-)Calculate the stress components that will affect the plane obtained by rotating the figure counterclockwise 25.
For the state of plane stress shown on the right, using a Mohr's circle technique, determine (a) the principal planes, (b) the principal stresses, (c) the maximum shearing stress and the corresponding normal stress. Sketch the results correspondingly on a correctly orientated stress element. 10 MPa -40 MPa 50 MPa
The strain components Ex, Ey, and Yxy are given for a point in a body subjected to plane strain. Determine the principal strains, the maximum in-plane shear strain, and the absolute maximum shear strain at the point. Show the angle 8p, the principal strain deformations, and the maximum in-plane shear strain distortion on a sketch. Ex = -400 μE, Ey = -295 μe, and Yxy = 1150 urad.Enter the angle such that -45%≤0ps +45° Answer: Ep1 = Ep2 = Ymax in-plane Yabsolute max. 8p= = με με D Hrad Hrad
Determine the magnitude of the shear stress (in units of MPa) when the state of stress is oriented 45 degrees from the element shown (aligned with line AB).
View Policies Show Attempt History Current Attempt in Progress The strain components Ex, Ey, and Yxy are given for a point in a body subjected to plane strain. Determine the principal strains, the maximum in-plane shear strain, and the absolute maximum shear strain at the point. Show the angle 8p, the principal strain deformations, and the maximum in-plane shear strain distortion on a sketch. Ex = -400 με, Ey = -310 με, and Yxy = 900 μrad. Enter the angle such that -45°≤0, +45°. Answer: Ep1 = Ep2 = Ymax in-plane - Yabsolute max. 8p= Save for Later με με 0 urad urad Attempts: 1 of 3 used Submit Answer 4
Determine the normal and shear stresses that occur in the n-n plane of the figure. Present a diagram showing such stresses on the n-n plane. Assume that the plate shown has a thickness of unit length.
A metal block (E = 60 GPa and Poisson's ratio of 0.35) rests on a rigid surface as shown below. It has uniformly applied loads which results in uniform stresses on the surfaces as shown. Assuming a compressive stress of 200 MPa along x-direction, determine the magnitude of stress oy for which the change in the height of the bock will be zero, (b) the corresponding change in the area of the face ABCD, and (c) the corresponding change in the area of the volume of the block. 40 2 100mm 25mm