Figure 7-50 Full Alternative Text 7-51. The eye bolt is used to support the load of 5 kip. Determine its diameter d to the nearest in. and the required thickness h to the nearest ĝin. of the support so that the washer will not penetrate or shear through it. The allowable normal stress for the bolt is σ allow = 21 ksi and the allowable shear stress for the supporting material is Tallow = 5 ksi. Prob. 7-51 -1 in.→ -d 5 kip

Figure 7-50 Full Alternative Text 7-51. The eye bolt is used to support the load of 5 kip. Determine its diameter d to the nearest in. and the required thickness h to the nearest ĝin. of the support so that the washer will not penetrate or shear through it. The allowable normal stress for the bolt is σ allow = 21 ksi and the allowable shear stress for the supporting material is Tallow = 5 ksi. Prob. 7-51 -1 in.→ -d 5 kip

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1-26. What is the required diameter of the pin Bfor the bell crank mechanism shown in the figure if an applied force of 60 kN at A is resisted by a force P at C? The allowable shearing stress is 100 MPa. Ans, 23.2 mm. 60 N A 150 mm 300 mm Pin B
7. Determine the stress developed in the Tensional Cord given that the cable's diameter is 0.6 inches and the bar weigh 6kips. Figure P-106 3 m 5 m 5 m E
FIl-1. Determine the minimum dimension a to the nearest FII-4. Determine the minimum dimension h to the nearest mm of the beam's cross section to safely support the load. The wood has an allowable normal stress of atow- 10 MPa and an allowable shear stress of Talow -1 MPa. in. of the beam's cross section to safely support the koad. The wood has an allowable normal stress of ale 2 ksi and an allowable shear stress of Tatow - 200 psi. 1.5 kip/ft 6kN 6kN 2a FIl-1 FII-4 FIl-2. Determine the minimum diameter d to the nearest in. of the rod to safely support the load. The rod is made of a material having an allowable normal stress of o- 20 ksi and an allowable shear stress of rh - 10 ksi. F1l-5. Determine the minimum dimension b to the nearest mm of the beam's cross section to safely support the load. The wood has an allowable normal stress of oow- 12 MPa and an allowable shear stress of Tlow - 1.5 MPa. 3 kip ft 50 kN 5 kN-m 5 kN-m -15 ft -1.5 ft 3kip m- -1 m FII-2 FIl-3. Determine the…
Determine the stress components acting on the inclined plane AB in if: normal stressy = 61MPa shear stressxy = -25 MPa solve the problem using the method of equilibrium. Find normal stress x' =? find shear stress x'y' =? I have a question regarding the answer you provided. The shear stress is -25MPa. You used a positive 25MPa in the solution. Why is that?
Determine the resulting maximum value of the normal stress. Specify the orientation of the plane on which these maximum values occur. **The answer is tensile stress is 0 ksi at 90 degrees. **The answer is compressive stress is 7 ksi at 0 degrees. Can you explain how that is? This was my thought process: I know that tensile would be zero because the force P is actually going inwards and not outwards. I know that means that there would be a compressive force. I am confused on the angles, how is a tensile force going 90 degress if there technically is no force in the tensile direction. And how is there a compressive force at 90 degrees if there is a stress? thank you!
Consider pinned Member A subjected to a tensile load shown below. Determine the expression of the area over which the punching stress to create the pinhole acts. Member A pm w P TOP VIEW pin Member A SIDE VIEW Select one: O A. A = Dt ОВ. А— т Dt OC. A = - D² 4 O D. A = (w – D)t
Link AB, of width b = 2 in. and thickness t = 1414 in., is used to support the end of a horizontal beam. The average normal stress in the link is -18 ksi and the average shearing stress in each of the two pins is 12 ksi. Determine the average bearing stress (ksi). **The way I had solved it was that I used the given normal stress to first find the P force needed to plus into my bearing stress formula. I still however need the diameter. The answer key says to use the given shear stress equation to find the diamter, how do you know to use that and not the shear stress formula again?
A vertical load P= 16 KN is applied as shown on member ABC that is held by the 15-mm diameter cable. The pin at the support C is in double shear and its diameter is 20mm. Determine the shear stress at pic C. Express your answer in "MPa" to the nearest whole number. Note: Use the rule in rounding-off numbers (normal rounding-off). DO NOT PUT A UNIT IN YOUR ANSWER, only the numerical value is required. * P A B 300 0. 6m C 0. 8m 0.4m
Q1/ A bracket is supported by means of 4 rivets of the same size. Design the 7. Alalkau diameter of the rivet if Ou (tenşile ultimate stress) for the rivet material is 560MPA. Which of the rivet has max resistance? 20KN 20KN B0mm 30 mm 30 mm 30 mm
The bolt shown on the picture is subjected to total tensile force of 90 kN. Determine the tensile stress at the body of the bolt and tensile stress at root of bolt. Find also the compressive stress at the head as the bolt bears on the surface to resist the tensile load.
Current Attempt in Progress The rectangular bar is connected to the support bracket with a 11-mm-diameter pin. The bar width is w-70 mm and the bar thickness is 10 mm. Each side of the bracket has the same dimensions as the bar. The average shear stress in the pin cannot ex t exceed 100 MPa, the bearing stress in the bar cannot exceed 150 MPa, and the bearing stress in the bracket cannot exceed 140 MPa. Determine the maximum value of Pax that can be supported by the structure. Answer: Pax 3 KN
1-63.M. The key in Figure 1-18 has the dimensions b = 10 min, h = 8 nim, and L = 22 min. Determine the shear stress in the key when 95 N-m of torque is transferred from the 35-mm-diameter shaft to the hub. Hub End view Shear plane Shear pl T=Torque -D=Shaft diameter T=F(D/2) F₁-Force of shaf F₂= Force of hub on 1 Shear area=A,=bxL