Ex. 681. Given a sinusoidal voltage source in series with R,L, and C. The sinusoidal frequency is 400 Hz. C=500 microFarad, V=30sin(wt) volts. phasor voltages across the capacitor, resistor, and inductor. R=2 Ohms, L=6 milliHenry, Find the phasor current, ans:8

Ex. 681. Given a sinusoidal voltage source in series with R,L, and C. The sinusoidal frequency is 400 Hz. C=500 microFarad, V=30sin(wt) volts. phasor voltages across the capacitor, resistor, and inductor. R=2 Ohms, L=6 milliHenry, Find the phasor current, ans:8

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: 3) Is it possible to directly subtract two power measurements expressed in dBm? Explain or prove…

A: (3) 1. In a strict sense, one can't directly perform addition or subtraction operations on dBm…

Q: determine the voltage gains: (a) Av=Voj/Vi and (b)Av=Vo/Vi. R. R Vio W R. Vo1 oVo R, Ri-1KΩ R2-10K…

Q: ng the circuit below determine the power taken by the six- 4.0 2 5.0 Q 18 V 3.0 2

Q: Solve the current using superposition theorem and solve for the individual currents of each…

Q: Q5 The charge of the condenser q() = [ 163) I(x)dx %3D is the rate of change of the current I.…

Q: 3.10. Let x[n] be a real and odd periodic signal with period N = 7 and Fourier coefficients ak.…

Q: IBQ, ICQ, VE, VCEQ, VCfor a transistor with VBE= 0.6 and β = 50. Draw and label the DC load-line.…

A: We need to find out current and voltage for given circuit

Q: An input æ(t) = u(t) is applied to an LTI system which produces corresponding output y(t) = -2u(t–…

Q: Solve the electric network. You may use any of the 3 solutions to SLE (Gauss Elim-REF, GJ-RREF, or…

A: The solution is given below

Q: Determine i in the circuit. 30 N 12Ω 5Ω 20 Ω 12V 25 Ω 60 2 15Ω 10 2

A: The solution is given below

Q: impe Z,- 100 2 which is terminated in a load impedance Z, - 50 2 and driven by a voltage source with…

A: Solution- l = 175.75λ i) l=175.75λ…

Q: in the network using Norton's Theorem. I 12 -j20 2.5IA 30 20230°v 148

Q: In the given circuit below, determine the current flowing through each resistors using; Maxwell's…

Q: A copper bar of rectangular cross section 2 cm by 8 cm and length 200 cm has a voltage drop of 50…

Q: Find the work done in moving at point charge Q = 20 μC from the origin to (4,2,0) m in the field…

A: The work done in moving a point charge can be calculated by using the general expression of work.

Q: EX: For the Circuit as shown in fig below, if Vo = 6 voit find Is. (using Kirchhoff's Law) Is (1 Vo…

A: In this question we need to find a current Is by using KVL and KCL

Q: Is = 25230°A, R2 = 902, R3 = 852, X2 = -402, N1 = 3, and N2 = 1. Com- Let Vs = 302 – 20°V, Z1 = 55+…

A: Complex Power can be explained as the representation of electrical power in form of complex number.

Q: Find the input resistance, voltage gain, current gain, and power gain for the amplifier. ßpc= 250.…

A: We need to find out input impedance , current, voltage and power gain for given circuit

Q: 3-phase slip ring motor gives a reading of 35 V across slip rings on open circuit when at candstill…

Q: What is transconductance explained simply?

Q: Q 1) A 3 phase induction motor is wound for 6 poles and is supplied from 50-Hz system. Calculate 1.…

Q: 1. A certain transmission line operating at w = 106 rad/s has a = 8 dB/m, ß = 1 rad/m and Z, = 60 +…

A: According to guidelines, only the first question will be solved. If any other solution is needed,…

Q: L{sinh 3t + sin 3t}

Q: R =1 kli R= 56 kn Ba = 100 Vec = 15 L e = 5V

Q: Good day can you help me with this problems TYIA. a.) ideal VCIS has gm = 45 mS. Determine io if Vi…

A: We will find out current and voltage for given amplifiers

Q: e Mesh Analysis matrix for Figure A4. Find "A" and "i" in terms c

Q: 7) Find the complement of the following expressions using Demorgan theorem (а) (х+y) + ху (b) (AB' +…

Q: ) Determine the input power in dBm received by an antenna with a gain of 45dB if the measured power…

A: We are supposed to be answer of first question as per guidelines.

Q: Solve for the electric network 120 12V 200 10V ww- 150 find the values of each current across each…

A: We need to find out current through each resistor .

Q: 4. We want a peak load voltage of 40 V out ofa bridge rectifier. What is the approximate rms value…

A: As per the guidelines of bartleby, we have to solve first 3 questions among the multiple subpart…

Q: Problem 2 X(1) + Ir X(1) is a zero mean white process with variance No. Let Y(t) = %3D 4X() a)…

A: X(t) is a zero-mean white process with variance N0. Y(t)=X(t)+dX(t)dt a) We need to find the PSD of…

Q: . Characteristic impedance of a transmission line is 502. Input impedance of the open circuited line…

A: Given, Characteristics impedance of transmission line, Zo=50 Ω Impedance of open circuit line,…

Q: 4. Assuming a 60 Hz system, how much time (in seconds) is the peak positive current behind the peak…

A: In this question we need to find a how much time is the peak positive current behind the peak…

Q: 1) Express point P(-2, 6, 3) in cylindrical and spherical coordinates. 2) Express vector A = 2.467a,…

Q: Q2/ Determine the period of each of the following functions: (a) (?) = (3+ 2)e3 (b) ) = (1+…

A: In this question we need to find a fundamental time period of the given signal.

Q: 2e 2 e - O 8/ (s^2 + 6s +1) Os/(8s^2 + 6s +1) Os/(s^2 + 6s +1) O 1/(8s^2 + 6s +1)

Q: What is the total equivalent resistance in Fig-9 if the1kohm resistor is shorted? 1k I;, = 2.75 mA…

A: Given circuit:

Q: Q1) Design the bias of MOSFET such that the Q-point is in middle of saturation region. Assume Vtn…

A: MOSFET: A Metal–Oxide–Semiconductor Field-Effect Transistor (MOSFET) is a field-effect transistor…

Q: 1. In the following figure: 2 kN Xc = 1 kN %3D R = 3 kN X, = + VL + VC VR e = 6 sin(314t + 60°) +

A: The solution is given below

Q: Identify the electrical symbol.

Q: Discuss how the circuit produces a Frequency Modulated Signal

A: According to the question, we need to discuss the working of the circuit shown below

Q: For the network shown, determine A,. 12 V 2.2 220 k2 B- 60 .-40 2 Z,

Q: can someone show me step by step how to do this problem and explain the concepts a)find R so that…

Q: term ‘DC motor’ is used to refer to any rotary electrical machine that converts direct current…

A: In this Question we will write about how rotor in a DC motor rotates....

Q: Plenum cabling is necessary in the area above the ceiling tile for the following reasons:

A: In this case, the reason behind the necessity of plenum cabling in the area above the ceiling needs…

Q: A balanced delta loads 5kW at a 0.7 lagging power factor. Find the delta phase impedance if the…

Q: Part A: Transformers A transformer core is constructed from sheet steel and the manufacturer's data…

A: The solution is given below

Q: as an external auditor, what are your 7 requirements of auditing that adherence to law and…

A: Everyone in the organization must observe safety standards since they are critical to the health and…

Q: For the voltage-divider circuit shown, check the appropriate analysis to be used and please solve…

Q: Use node analysis to determine node voltages and branch currents in the image below.

A: In this question we need to find a node voltages and branch currents in the image below.

Concept explainers

Single Phase Induction Motor

The single-phase induction motor or engine consists of a single rotating phase in the stator and a rotating cage in the rotor. When phase one supply is connected to the stator winding, a magnetic field is generated. In the pulsating field, the rotor does not rotate due to inertia. So, a single-phase import motor does not start and requires some initial methods.

Question

Ex. 681. Given a sinusoidal voltage source in series with R,L, and C. The
sinusoidal frequency is 400 Hz.
C=500 microFarad, V=30sin(wt) volts.
phasor voltages across the capacitor, resistor, and inductor.
R=2 Ohms, L=6 milliHenry,
Find the phasor current,
ans:8

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

An electrical circuit with a sinusoidal voltage source, a resistor, and a capacitor all connected in series. The voltage across the capacitor: Select one: a. Leads the current in the capacitor by exactly 90o b. Is in phase with the sinusoidal voltage source c. Is in phase with the voltage across the resistor d. Leads the current in the circuit by 90o e. Lags the current in the circuit by 90o
A 10.0-μF capacitor and a 2.00-H inductor are connected in series with a 60.0-Hz source whose rms output is 100 V. Finda. the rms current in the circuit.b. the voltage drop across the inductor. c. the voltage drop across the capacitor.
A capacitor has a reactance of 40 when operated on a 50 Hz supply. Determine the value of its capacitance. In a series R–L circuit the p.d. across the resistance R is 12V and the p.d. across the inductance L is 5V. Find the supply voltage and the phase angle between current and voltage
A capacitor in series with a 200 ohms resistor draws a current of 0.3 ampere from 120 volts, 60 hz source. What is the value of the capacitor in microfarad? a. 8.7 b. 9.7 c. 6.7 d. 7.7
Shown in the figure below is an "RL" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 9.84 Volts and is running at a frequency of f = 8.585e+04 Hz. The resistor has a resistance of R = 2170 and the inductor has an inductance of L = 3.54e-03 Henries. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Determine the numerical value of Ztot = 2890.5 Determine the numerical value of $z= = 41 Determine the current through the circuit: • I(PEAK) = 4.81E-3 • I(RMS) = 3.404E-3 Determine the voltage across the resistor: • VR(PEAK) = 7.387 • VR(RMS) = 5.22 ✔✔ Amps ✔Amps Write the FORMULA for the phase of the total impedance of the circuit z... = | tan-1 2701 R x Volts X Volts Determine the voltage across the inductor: • VL(PEAK) = 9.184 • VL(RMS) = 6.49 ✔ Volts Volts L R²+ WL- ✔ degrees 2 If a second circuit were connected in parallel with the inductor, this circuit would be considered as: O a low-pass filter O a capacitive switcher…
Please explain this question properly A capacitor has a reactance of 40 when operated on a 50 Hz supply. Determine the value of its capacitance. In a series R–L circuit the p.d. across the resistance R is 12V and the p.d. across the inductance L is 5V. Find the supply voltage and the phase angle between current and voltage
Answer the following with illustration and solution. 1.) A circuit consisting of a resistor of 5kohms in series with a capacitor of 10 nanofarad is connected across a 16v sinusoidal supply. Calculate the output voltage at a frequency of 60Hz and again at frequency of 120Hz. This is the example/guide that might help.
A 250-V circuit, consisting of a resistor, an inductor and a capacitor in series, resonates at 50 Hz. Thecurrent is then 1A and the p.d. across the capacitor is 500 V. Calculate (i) the resistance (ii) theinductance and (iii) the capacitance Answer:
An inductor, a capacitor, and a resistor are connected in parallel with a function generator. The inductor draws 100mA RMS, the capacitor draws 150mA RMS, and the resistor draws 200mA RMS. Find the magnitude of the total current.
What is the value of capacitance if the capacitive reactance is 50 Q .Assume frequency of supply as 50 Hz ? a. 53.3x10-5 F O b. 5.3x10-5 F c. 6.36x10-5 E d. 63.3x10-5 F
The current through a 50 mH inductor is given below. Use Ohm’s Law to find the voltage. Convert to polar form, find the impedance and complete the math, then convert back to the waveform at i1 = 7.5sin(2500t – 20°) mA and i2 = 5.9sin(200t + 40°) mA
7 Find the average and effective values of voltage for sinusoidal waveform shown in Figure. Vm = 100 V 2x x14 9714 [Ans: 27.17 V, 47. 67 V]