e) The total power content of an AM signal is 1000 W. Determine the carrier power Pc and the sideband power P, and power efficiency when the modulation index is 0.5? f) An amplitude modulated wave has a power at its carrier frequency (Pc) of 800 W. determine the sideband power P, and total power when the modulation factor is 0.8?

e) The total power content of an AM signal is 1000 W. Determine the carrier power Pc and the sideband power P, and power efficiency when the modulation index is 0.5? f) An amplitude modulated wave has a power at its carrier frequency (Pc) of 800 W. determine the sideband power P, and total power when the modulation factor is 0.8?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Question 4. Select the statement that best describes the PM wave.a. Carrier phase angle changes represent the PM modulated signal, however, unlike FM and AM modulatedcarriers, it is not always easy to see these phase changes in the plot.b. The FM signal accurately represents the message.c. Although PM and FM techniques are classified as angular modulation techniques, they cannot be usedinterchangeably (i.e., modulated with FM and demodulated with PM, and visa versa).d. All statements are correct.
6. A400W, 1MHZ carrier is amplitude-modulated with a sinusoidal signal Of 2500HZ. The depth of modulation is 75%. Calculate the sideband frequencies, bandwidth, and power in sidebands and the total power in modulated wave. 5 band wid th
Q7. Figure Q7(a) shows the spectrum of a frequency modulated waveform with a sinusoidal modulation. 12 4.8 5.0 5.2 5.4 5.6 5.8 6.0 Frequency/MHz Figure Q7: (a) Spectrum of a frequency modulated waveform with a sinusoidal modulation. (a) Is this modulated waveform described as narrowband or as wideband? (b) What is the value of the carrier frequency? (c) What is the value of the modulation frequency? (d) Determine the value of the peak frequency deviation. Plots of Bessel functions of the first kind are provided below in Figure Q7(b) to assist you. (e) Estimate the fraction of the total signal power at the carrier frequency. (f) Detection of such a frequency modulated signal is usually accomplished with the use of a discriminator. Describe the function of a discriminator. (g) What is the equivalent AM modulation index obtained if this signal in Figure Q7(a) is demodulated with a high-pass RC filter discriminator? J„(x) 1.0 0.8 0.6 0.4 0.2 -0.2 -0.4 Figure Q7: (b) Bessel functions of the…
H.W A carrier signal given by 10cos27×108t volt is FM modulatedby single tone message 4cos2nx103t voltif the modulation constantis 1000 HzlVolt a) Compute max. frequency deviation and deviation ratio. b) Write the equation of modulatedwave. c) Sketch the spectrum. d) Calculate sidebands carrierand total power.
S Answer the two following questions: A. A sinusoidally modulated AM waveform is shown below: Determine: (a) Peak amplitude of the upper and lower side frequencies. (b) Peak amplitude of the unmodulated carrier. (c) The modulation index. (d) The transmission efficiency. (e) The amplitude of the carrier which must be added or subtracted to attain a modulation index of 0.5. 16V 8V- -8V. -16V-
1. A modulating signal with an equation m cos2n(2k)t modulates a carrier signal with a peak amplitude of 9V and a frequency of 500 kHz. 5sin2n(3k)t + 6cos2n(6k)t + A. Calculate the RMS voltage of the modulating signal. B. Calculate the RMS voltage of the AM signal. C. Determine the bandwidth of the AM signal. D. Draw the frequency spectrum of the AM signal. Label completely.
In an Amplitude Modulator where the carrier and modulating signals are both sine waves, the frequency spectrum of the resulting AM signal is shown below. 10V 2V 2V kHz 803 808.6 a) Determine the equation of the modulating signal b) Calculate the bandwidth of the AM signal c) Calculate the effective current of the AM signal thru a 75-ohm load. d) Sketch the AM wave and label the maximum and minimum voltage of the signal.
A carrier signal given by 10cos27x108t volt is FM modulated by single tone message 4cos27Tx103t volt if the modulation constant is 1000 Hz/Volt a) Compute max. frequency deviation and deviation ratio. b) Write the equation of modulated wave. c) Sketch the spectrum. d) Calculate sidebands carrier and total power.
AC H.W Fc A carrier signal given by 10 cos 2n x 10t volt is FM modulated by single te Hz message 4 cos 2n x 10°t volt if the modulation constant is 1000 Am Volt Fm a) Compute max. frequency deviation and deviation ratio.A. E b) Write the equation of modulated wave. Ac c) Sketch the spectrum. d) Calculate sidebands carrier and total power.
A 1-MHz carrier with an amplitude of 1 volt peak is modulated by a 1-kHz signal with m=0.5. Sketch the voltage spectrum. An additional 2-kHz signal modulates the carrier with m = 0.2. Sketch the voltage spectrum.
Q3: A sinusoidally modulated AM waveform is shown below, Determine: 1. Peak amplitude of the upper and lower side frequencies. 2. Peak amplitude of the unmodulated carrier. 3. The modulation index and it is percentage. 4. The total power and the power efficiency. 5. Plot the frequency and the power spectrum of the modulated signal if the frequency of the carrier and the modulating signal are 2MHz and 15KHz respectively. 12 6 0 -6 -12 T
A 10-MHz sinusoidal carrier wave of amplitude 1o mV is modulated by a 5 kHz sinusoidal audio signal wave of amplitude 6 mV. What is the modulation factor?