During the manufacture of hard disks, the height between the disk and the head, the headlift, must be controlled. One manufacturer recorded 0.239 0.246 0.245 0.243 0.239 0.241 0.248 0.246 0.243 0.242 0.251 0.246 Find the a) Sample mean b) Sample standard deviation c) Coefficient of variation

During the manufacture of hard disks, the height between the disk and the head, the headlift, must be controlled. One manufacturer recorded 0.239 0.246 0.245 0.243 0.239 0.241 0.248 0.246 0.243 0.242 0.251 0.246 Find the a) Sample mean b) Sample standard deviation c) Coefficient of variation

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Rods are mass produced by a machine. The specification required the length of each rod to be between 42.49 cm and 42.51 cm. The machine produces rods whose lengths are normally distributed with standard deviation 0.005 cm. a) b) Determine the percentage of rods produced which would be rejected if the machine is set so that the mean length of the rods is 42.501 cm. c) Determine the mean length the machine must be set so that only 3 rods in 1,000 will be of length less than 42.494 cm. If there is a need to reduce the total percentage of rejects (oversize and undersize) what should be the mean setting of the machine? You are required to show the normal distribution curve to determine the answer for Part (a) and (b).
Measurement in Engineering Question is image C) ? c) Determine a 95% confidence interval for Nu and report the value.
A population of nomally-distributed measurements has a mean u = 2.850 and standard deviation o = 0.020. A total of 40 measurements were taken in 10 samples of size n=4. A) What is the mean i of the sample means. B) What is the standard deviation s, of the sample means? C) Find the 3 standard deviation spread (or range) of measurements. D) Find the 3 standard deviation spread (or range) of sample means. E) If the parent measurements were not normally-distributed, would you expect the distribution of sample means to be normally distributed? Why or why not. + A) + B) + C) + D)
tensile test PCKN) AL (Mm) Dimensions of the sample be fore e xamin ation 4.12 0. 29 D= 9.5mm L=50 7.64 0.55 12 0.91 15, 8 4 l.27 19.5 1.6 2५.3 2. 11 28 3.5 Dimensions of the sample after exam ination 31.2 5.25 d - 5.7 33.6 2=? 35 8.75 35.7 1o.5 36 12.2 31.5 15.7 27.8 15.8
The volume of water in commercially supplied fresh drinking water containers is approximately normally distributed with mean 70 liters and standard deviation 0.75 liters. Estimate the proportion of containers likely to contain a) in excess of 70.9 liters, b) at most 68.2 liters, c) less than 70.5 liters.
Multiple choice questions. Choose correct answer 1. Sampling is used because A) it increases the data quality B) the processing of entire data can be time-consuming C) it reduces dimensionality D) it helps find missing data Answer: 2) Correlation coefficient is always in the range A) 0 to 1 B) -1 to 1 C) 0 to 100 D) 1 to 2 Answer: True or False. Choose correct answer 3. Regression analysis is used to predict a value of a continuous valued variable. Answer:
2. Construct the P Chart for the following data. No.of No.of Sample pieces defective No. pieces inspected! 'found 1 500 99 2 500 51 500 38 4 500 69 5 500 38 6 500 53 7 500 99 8 500 53 9. 500 80 10 500 36
The diameters of shafts with a nominal size of dn = 68 mm must be within limits dmax = 68.045 mm and dmin = 68.015 mm. What are the upper deviation es. the lower deviation ei. and the tolerance Td? es ei Td 1) -0.015 +0.045 0.030 2) +0.045 -0.015 0.060 3) +0.045 +0.015 0.030 4) +0.015 -0.045 0.060
Problem 2 The fatigue data for a steel alloy are given as follows. Stress amp, 470 440 390 350 300 290 290 290 S(MPa) Cycle to failure (N) 1.0x104 3.0x10* 1.0x105 3.0x105 1.0x106 3.0x10 1.0x107 1.0x10 f) Make an S-N plot of the data. g) Select S-N curve, select add trend line and in trend line options click power and display equation on the chart. h) Determine the material constants A and B by fitting this plot to the equation S=AN°. i) Is A and B the same as in problem 1? Why or why not? j) Determine the Fatigue limit or Fatigue strength whichever is applicable for this metal. k) Estimate fatigue strength at 2.0x 10* and 6.0x105 cycles.
For the following system, calculate the mode shapes Select one 10.4597 0.6277", 10.8881 -0325) 11 0.9846) 1-1 0.1735)"
TRUE OR FALSE 1.) In rheology, food materials of higher viscosity have higher resistance to flow. 2.) Specific heat is the amount of heat needed to raise the temperature of a unit mass of an object one degree higher without change of phase 3.) Surface area, is related to size but also depends on particle shape. 4.) Size can be correlated with weight given that the material has more or less uniform composition. 5.) Latent heat of fusion is the amount of heat that must be removed to convert water to ice and is also the same as the amount of heat added to convert ice to water.
B.How does the color of t-shirt you wear affect its temperature? te three variations of the independent variable below. IF THEN BECAUSE (Write a SPECIFIC action you can do) (Make a prediction about what you are measuring) (Reason why from your knowledge/research)