Your answer is partially correct.Determine the absolute maximum shear stress for each of the following plane stressstates for which the principal stresses are given.(a) op1 = 2780 psi, o,2 = -2440 psi, op3 = 0(b) Op1 = 58 MPa, Op2 = 35 MPa, Op3 = 0Answer:(a) Tabs maxpsi1390(b) Tabs maxMPa29

Answered: Image /qna-images/answer/f594fe5a-bf07-45bb-b2a0-dc5a827ddb63.jpg

Determine the absolute maximum shear stress for each of the following plane stre states for which the principal stresses are given. (a) Op1 = 2780 psi, op2 = -2440 psi, op3 = 0 (b) op1 = 58 MPa, Op2 = 35 MPa, op3 = 0

Determine the absolute maximum shear stress for each of the following plane stre states for which the principal stresses are given. (a) Op1 = 2780 psi, op2 = -2440 psi, op3 = 0 (b) op1 = 58 MPa, Op2 = 35 MPa, op3 = 0

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 4. If the open cylindrical container rotates at an angular velocity of 8 rad/s, determine the…

Q: 4. A reinforced concrete T-beam has the following properties: Flange width, bf = 1,350 mm Width of…

Q: 1. The overhanging beam in the Figure carries distributed loads. Using the area method. Draw the…

A: Draw shear force and bending moment diagram Using area method.

Q: A reinforced concrete T-beam has the following properties: Flange width, bf = 1350 mm Width of…

Q: 7Ose vin fual work to c le tkelonizonked displumnt rointE W can use inkegention barnot needed. tabe…

Q: 4) When the required torque has been achieved the tension control bolt splined end spins off? Tor F…

A: Torque- It tries to rotate a body about an axis.

Q: From the given truss, which member has an internal force of 57.7 kN TENSION? B 5 m D 5 m 5 m 5 m 5 m…

Q: 2. Course AB of a five-sided traverse runs due north. From the balanced interior angles to the…

Q: a 3-m inclined rectangular gate, AB, is used to hold liquid X (s=1.23) with height, h. To avoid the…

Q: Q15 An HSS 14.000x0.500 made of A500 grade C steel is used as a column with fixed ends and is 20ft…

A: E = 29000 ksi ; fy = 50 ksi Le = kL = 0.65x20 ft = 13ft = 13 x 12 = 156 inch For HSS 14*0.5…

Q: A mild steel bar 60mm in diameter is simply supported and has a span of 2m. What load suspended at…

Q: A rectangular beam 250mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars…

A: From the given data:

Q: There are misconceptions on concrete curing and setting time. What is concrete/ cement setting time?…

A: We have to define the concrete setting time and concrete curing

Q: or questions 1A and 1B, consider the figure below and the given modulus lasticity E, and moment of…

A: To find slope and deflection at free end

Q: If the shaft power is 82kw and the cost of the electricity is $0.10 kwh; estimate the cost of the…

Q: Determine the tensile steel ratio of a singly reinforced concrete beam for the following conditions…

Q: The stress at a point is shown on the element. Determine (a) principal stress, (b) maximum in-plane…

A: The compressive stress on vertical face, σ=-45MPaThe compressive stress on horizontal face,…

Q: 16 kN | 4 kN/m 20 kN 2 kN/m A 4m- 8 m 8 m FIG. P4.33

A: Shearforce : Clock wise positive Anticlockwise-ve Bending moment : Clockwise negative…

Q: 20 sod 0.4 m 0.7 m 0.7m Force in Member AB in N. Round off to the nearest whole number.

Q: A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars…

A: Given Data: beam 250 mm wide, 500 mm deep top with 2-16-mm bars centroid at the top is 80 mm and at…

Q: 12 kN 3 m 3m C 4 m 8 m 15 kN 4 m 20 kN/m B Refer to the figure, what is the moment reaction at…

A: A loaded frame structure is given and it has been asked to determine support reactions at A. Please…

Q: This composite shape is composed of a square, a half-circle, a triangle and a circular hole.…

A: Figure is as shown

Q: Which of the following gives the reaction at F in the given beam? 24 kN 10 kN/ m A F 20 kN. m B C D…

Q: 5. The rectangular channel in Fig P10.120 contains a V-notch weir as shown. The intent is to meter…

A: Figure shows the rectangular channel containing a V notch weir. From figure H=y-Y=2-Y From…

Q: 12 kN 3 m 3 m IC D 4 m 8m 15 kN 4 m 20 kN/m Refer to the figure, what is the reaction at support B…

A: A loaded frame is given and it has been asked to determine support reactions at B. Please refer step…

Q: Situation 12. With reference to the NSCP 2015, choose the correct statement: 37. For design of…

A: Tension controlled section are the RCC members which provide resistance due to primary tension…

Q: . Draw a simple horizontal curve label the curve and define each term

A: Simple Horizontal Curve:

Q: The figure shown is the cross section on the fixed support of a propped beam that carries a moment…

Q: For the cantilever steel beam [E = 220 GPa; I = 83 x 106 mm4), use the double-integration method to…

Q: 25. Calculate the nominal shear strength of concrete, using simplified formula of NSCP 2015. = kN…

A: fc'=21 MPafy=280 MPad=425 mmbw=275 mm10 mm 2-legged stiruppsspacing=200 mmAs per the company's…

Q: For the built-up shape shown in the figure, determine: A. The elastic section modulus considering…

Q: F a a A 30° 60° AB

Q: ep in digital format plea

Q: 5.18 (B). A uniform horizontal beam ABC is 0.75 m long and is simply supported at A and B, 0.5 m…

Q: Determine the value of the maximum deflection and the location of the maximum deflection.

Q: For the cantilever steel beam [E = 220 GPa; I= 102 x 106 mm], use the double-integration method to…

Q: Problem 5. A small river is in flood stage and you need to estimate the flow rate through it. The…

A: Q=1.49nAR23S12 A= 100*10+500*2= 2000 ft2 P= 10+100+8+500+2= 620 ft R= A/P= 2000/620= 3.226 ft…

Q: A steel rod of 20 mm diameter is used as a tie member in a roof bracing system, and may be subjected…

A: Given data- Diameter D=20 mmSlenderness ratio λ=350To Find-Maximum permissible length L

Q: CLASSIFY IF STATICALLY DETERMINATE OR STATICALLY INDETERMINATE, STABLE OR UNSTABLE. IF…

Q: If a triangle of height d and base a is vertical and submerged in liquid with its vertex a distance…

A: The center of pressure is the point where the total sum of a pressure field acts on a body, causing…

Q: Determine vertical support reaction

A: Given data : The total span of cantilever of beam L=8 m The total intensity of uniformly distributed…

Q: For the loading shown, use the double-integration method to determine (a) the equation of the…

Q: Situaton 18: The given angle bar L125x75x12mm with Ag = 2,269 sq.mm. is connected to a gusset plate…

Q: The Howe bridge truss is loaded shown. Use method of sections to determine the axial forces in the…

Q: (a) the slope of the beam at C (positive if counterclockwise and negative if o (b) the deflection of…

Q: Discuss the factors accounted for by the modification factor K12 in the design of timber members.…

A: Permissible stress : Civil engineers utilize a design philosophy known as permissible stress design.…

Q: The rectangular channel in Fig P10.120 contains a V-notch weir as shown. The intent is to meter flow…

Q: Steel joists are manufactured in different series to account for which of the following?…

A: Steel joists- Steel joists are an open web, lightweight metal trusses with matching hooks and a…

Q: Determine the absolute maximum shear stress for each of the following plane stress states f (a) Op1…

A: To find absolute max shear stress

Q: A 30-cm by 15-cm Venturi meter is mounted on a vertical pipe with the flow upward. One hundred…

Concept explainers

Solid Mechanics

Engineering mechanics is a branch of science that deals with forces causing bulk motion in bodies and the effect that these forces cause on the bodies. Engineering mechanics does not deal with the internal changes that occur on account of these external forces. The internal effects in a body or a material under the action of external forces are studied in a new branch of science called solid mechanics, the strength of materials, or the mechanical behavior of engineering materials.

Question

Your answer is partially correct.
Determine the absolute maximum shear stress for each of the following plane stress
states for which the principal stresses are given.
(a) op1 = 2780 psi, o,2 = -2440 psi, op3 = 0
(b) Op1 = 58 MPa, Op2 = 35 MPa, Op3 = 0
Answer:
(a) Tabs max
psi
1390
(b) Tabs max
MPa
29

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

1) Figure 1 shows an element with stresses. Angle 1 Oy Tyx Txy Tyx Figure 1 Point B- x-direction stress 60MPA(tension), y-direction stress 40MPA(compression), positive shear stress 30MPA a) From basic priciples determine the stresses on the plane of the indicated angle 1. (20°), Show al calculations. Draw the orientation of the stress block for this scenario. b) Repeat question (a) using a Mohr circle.
A tapered cantilever beam AB having rectangular cross sections is subjected to a concentrated load P = 46 lb and a couple Mo = 790 lb - in. acting at the free end [see the figure part (a)). The width b of the beam is constant and equal to 1.0 in., but the height varies linearly from ha = 2.0 in. at the loaded end to hp = 3.0 in. at the support. Use L = 20 in. Мо В hg (a) 3P qo = T Мо (b) ЗР 90 =7 \ Mo.
A cube (E - 20OGPA) is experiencing stress from all directions. Along the x-direction, there is a compressive stress of 50MPA. Along the y-direction, there is a tensile stress of 80MPA. Along the z-direction, there is a tensile stress of 100MPA. Solve the strain along the z-axis if the Poisson's Ratio is 0.3. O 0.000520 O 0.000455 O 0.000416 0.000325
Determine Value of x if the Normal stress at rod is equal to the stress at rectangular pipe A =400 mm? T. Rod F = 8kN A =650 mm2 rectangular Pipe
The tensile member shown, 60mm x 80mm in cross-section is subjected to a load of 250kN. The plane AA’ makes an angle of 15o with the x-axis. What is the tensile stress of section AA’? Determine the shear stress on plane AA’ At what angle of plane AA’ is the shear maximum.
Part A The stress at a point is shown on the element. Suppose that o, = 105 MPа, т - 158 MPа Determine the principal stress. (Figure 1) Enter your answers numerically using three significant figures separated by commas. VG AEo t vec ? Omax, Oint, Omin = MPа Submit Request Answer Part B Determine the absolute maximum shear stress. Express your answer with three significant figures and use the appropriate units. HA O ) ? Figure 1 of 1 > Value Units Timax in-plane = Submit Request Answer Provide Feedback
(A) he figure below shows three metal cubes A, B, C of side 100 mm in direct contact, resting on a rigid base and confined in x-coordinate direction between two rigid end plate. If the upper face of the center cube B is subjected to uniform compressive stress of 0.5 kN/mm², compute for cube B, the following: (i) The direct stress in x-direction (₂) (ii) The direct strains in the three coordinates directions x, y and z (iii) The volumetric strain Rigid A E=150 kN/mm² μ = 0.25 o₂ = 0.5 kN/mm² B E = 200 kN/mm² μ = 0.3 -Rigid C E = 150 kN/mm² μ = 0.25 Rigid
What are appropriate relations established from the calculation of maximum shear stress in a thin circular tube? 4 (b) t = (a) Tmax Tavg 3 'avg max 3 4 S Rỉ + R2R1+ R3 (c) Tmax when (R, = = 2avg - R.) (d) Tmax 3 A Rỉ + R? Here, (R, > R1) and S is shear force at the cross sectional and A is cross sectional area.
For the stress block shown, what is OP2 if OP1 = 140 MPa (T)? A.60 MPa (T) 40 MPa B.60 MPa (C) C.20 MPa (C) D.20 MPa (T) Txy Which among the following is ALWAYS TRUE about the maximum in-plane shear stress? A.It acts on planes 450 from principal planes. B.It is equal to the absolute maximum shear stress. C.It is equal to the principal stress with higher magnitude. D.It acts on planes with zero normal stress. 120 MPa
2D stress at a point is given by a matrix 100 301 = [1 30 20 shear stress in MPa is Oxx Txy Tyx Oyy The maximum MPa
Problem 5-82 The Am1004-T61 magnesium tube is bonded to the A-36 steel rod. If a torque of T = 5 kN m is applied to end A, determine the maximum shear stress in each material. Sketch the shear stress distribution. 900 mm B 80 mm, 40 mm
Question 2. The square plate ABCD is deformed into the shape shown by the dashed lines. If DC has a normal strain Ex = 0.005, DA has a normal strain ey = 0.004 at D, Yxy = 0.01rad determine the shear strain at point E with respect to the x' and y' axes. 600 mm- 600 mm E D