Design a bridge rectifier circuit to provide an output of 100 VDC. Calculate the diodes PIV rating and the transformer's turns ratio, if power is taken from the 120 V line AC supply. ***Type the letter of the correct answer. 1. The diodes PIV rating is: a. 157.23 V b. 222.36 V c. 314.47 V d. 111.18 V 2. The transformer's turns ratio is: a. 0.3816 b. 1.0793 c. 0.7632 d. 0.5397

Design a bridge rectifier circuit to provide an output of 100 VDC. Calculate the diodes PIV rating and the transformer's turns ratio, if power is taken from the 120 V line AC supply. ***Type the letter of the correct answer. 1. The diodes PIV rating is: a. 157.23 V b. 222.36 V c. 314.47 V d. 111.18 V 2. The transformer's turns ratio is: a. 0.3816 b. 1.0793 c. 0.7632 d. 0.5397

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The peak output voltage for the bridge rectifier in the figure is_______Volts. Assuming ideal diodes, the PIV rating required for the diodes is ______Volts. The transformer is specified to have 12 Vrms secondary voltage for the standard 110 V across the primary.
Which of the following statements about bridge tip rectifiers is false? A) If the 1-phase type has source inductance, the average value of the output voltage is lower than in the absence of the inductance. B) The average output voltage value of the 1-phase type is 0.9 times the peak voltage of the network. C) none D) There are only odd harmonics in the current drawn by the 1-phase type from the mains. E) The average value of the output voltage of the 3-phase type is larger as the 3-phase and 1-phase types are compared
II. A center tapped full-wave rectifier circuit has the following specifications: ac supply line is 120 volts, RMS of the total secondary voltage is 80 volts and the load resistance is 10 ohms. Determine the following: (a) V,1 RMS, (b) V32 AVE, (c) Vo1 RMS and Vo2 AVE (d) I, RMS, (e) PLAVE, (f) turns ratio of the transformer
Figure 1 shows the circuit diagram for a simple d.c. power supply. a. Identify the type of rectifier circuit represented in figure 1 and explain the operation of the circuit with reference to the function of each component within the circuit. b. Sketch to scale the voltage across R as a function of time showing its relationship to the secondary voltage from the transformer.
Is Bridge Full Wave Rectifier only working with Transformers or can we use it with AC source as well? If you are agree with this then provide any advantage of this rectifier circuit without using the transformers OR if you are disagree then provide justification of your answer.
1) How is the diode and zener diode in the electronic circuit and how they work?indicate the differences between them.2) Can a zener diode be used instead of a regular diode? please explain.3) Is it to step down and rectify the 220V AC signal by means of a transformer or to convert 220 V?rectify it and then reduce its value to the desired DC level using a voltage divider circuit?suitable.?4) Bridge type full wave rectification with two diodes full wave rectification using a medium ended transformerCompare the rectifier circuit and list its advantages and disadvantages relative to each other.5) What is the concept of PIV (Peak Inverse Voltage) for rectifier circuits?For which rectifier circuits is this value more important?
Part A- Why negative peaks are eliminated in Half Wave Rectification and how this can be achieved in Full Wave Rectification without eliminating these peaks? Part B- Is Bridge Full Wave Rectifier only working with Transformers or can we use it with AC source as well? If you are agree with this then provide any advantage of this rectifier circuit without using the transformers OR if you are disagree then provide justification of your answer.
The purpose of the current limiting resistor in a Zener diode circuit is to _________. a. Maintain a constant current through the load resistor b. Maintain a constant voltage across the Zener diode c. Maintain a constant current through the Zener diode d. Drop the additional voltage from the power supply in order to maintain a constant voltage across the Zener diode Please answer it clearly.
In a centre-tapped full wave rectifier having a load resistance resistance equals 3 2. The turn's ratio of the centre tapped transformer is 20:1. The primary winding of transformer is fed from a supply voltage of 220 V (RMS ), 50 Hz. Determine a) Average and RMS value of load currents b) DC voltage and DC power output c) AC input power d) ripple factor and e) rectifier efficiency. 750 52 diode forward bias
Q1) A 3-phase, half-wave thyristor rectifier feeds a resistive load. The load resistance is 80 2 and the supply voltage is 220 volts per phase, 50HZ. Calculate the mean values of the load voltage and current if the delay angle a is 30°. Then, sketch the block diagram of the circuit.
A load is connected in the Full Bridge rectifier circuit (Four Diodes). Usedtransformer primary voltage value is 220 V (rms). The transformer winding ratio is 1:10.Using the 0.7 V model of the diode,Load Rating: 7 K Ohmsa) How many % of conduction does each diode branch stay on?b) Find the average values of the load voltage.c) Find the average values of the load current.d) Find the effective value of the load voltage.e) Find the effective value of the load current.
1. The Figure (i) and Figure (ii) show the centre-tap and bridge type circuits having the same load resistance and transformer turn ratio. The primary of each is connected to 230V, 50 Hz supply. (i) Find the d.c. voltage in each case. (ii) PIV for each case for the same d.c. output. Assume the diodes to be ideal. 5:1 5:1 100 2 100 2 230 V ww 230 V (i) (ii)