(d) The partial load is trapezoidal into two triangular and rectangular sections. The area of the rectangle represents the load and its center of gravity is? 1. In the first third of the rectangle. 2.At the top of the rectangle 3. In the middle of the rectangle. 4. At one end of the rectan.

(d) The partial load is trapezoidal into two triangular and rectangular sections. The area of the rectangle represents the load and its center of gravity is? 1. In the first third of the rectangle. 2.At the top of the rectangle 3. In the middle of the rectangle. 4. At one end of the rectan.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Sherwn 2. Kg 6.2 is altached Cen Stant K = Lengt releafed Coller at C to Sering With Brym If ke Emenk A Fig th en d en ef 0-75 m. frem rest et Peint A. accelera tion end Hhe hema fede en He Collar at un 8tretehed is Coller Celeulate Ferce Hhe it's ef the in sleant 0-75M. Ih = 3x /m wwww
The figure shows the Russel fracture traction device and a mechanical model of the leg. The leg is held in balance in the position indicated by the two weights attached to the two cables. The total weight of the leg and the cast is W=250 N. The distance between the points A and B where the cables are attached to the leg is given as L=100 cm and the angle of the leg with the horizontal is γ=6°. Point C is the center of gravity of the cast and leg at three quarters of the L measured from point A (3L/4= 75 cm). The angle that cable 2 makes with the horizontal is measured as β=40°. Accordingly, in order for the leg to remain in balance in the shown position; a) Find the tensile force T1 in cable 1. (Write your result in N) Answerb) Find the tensile force T2 in cable 2. (Write your result in N) Answerc) Find the angle α of cable 1 with the horizontal. Response
-2- 6.Drand the mechanical circuit for the rolakionale mechamel szolem. b1 Find the drano for fervehen B (moter) el Find B,ls) eesponse if Tom, is shep fone from.
An old single-leaf drawbridge is made of a thin rectangular board of mass M, width a(into the page) and length bwhich can pivot at oneend. When it is not in use, the span of the bridge is held at a 60ºangle from the horizontal direction. The two ideal cables that holdit at itsfarther end areanchored to the ground so that they forma 30º angle with the horizontal direction, as shown in Fig. 3.The acceleration due to gravity has magnitude g. a) Set up all the detailed scalar equations (not the general version)expressing the static equilibrium of the drawbridge. b) Determine the magnitude T of the tension force exerted by each of the two cables on the board. c)Determine the magnitude Fh of the hinge force exerted on the board and the angle h that the force forms with respect to the horizontal direction.
Find the force P needed to hold the 10-m-long cylindrical object in position as shown in figure.
The figure shows a mechanical model of the Russel fracture traction device and the leg. The leg is held in balance in the position indicated by the two weights attached to the two cables. The total weight of the leg and the cast is W=200 N. The horizontal distance between points A and B where the cables are attached to the leg is L=100 cm and the vertical distance is d=10 cm . Point C is the center of gravity of the cast and leg at three quarters of the L measured from point A ( 3L/4= 75 cm) . The angle that cable 2 makes with the horizontal is measured as β=40 ° . Accordingly, in order for the leg to remain in balance in the position shown; a) Find the tensile force T 1 in cable 1 . (Write your result in N ) b) Find the tensile force T 2 in cable 2 . (Write your result in N ) c) Find the angle α of cable 1 with the horizontal
Situation 4 The truee ia lended se anown. 60 kN 120 kN 120 kN 120 kN 3m. 3m 6m 3m Cnccse the magnitude (kN) ana type (tenaion or ocmpression) cf the foroe in member AB. NOTE: Alweye ohocee two (2) anewere but if the member ia e zero-foroe member ohoose one (1) anawer only. Seleot the correct reoponoe(o): 180 260 50 63.25 56.06 Teneion 160 60 Compression 7211 100 O O O O O O
The spring clamp of Fig. block Fagainst the floor. The force in the spring is F = k(e – lo), where e is the present length of the spring, lo = 3 in. is the unstretched length of the spring, and k = 240 lb/ft is the spring constant. Determine all forces acting on mem- ber ÁBC of the spring clamp and the force exerted by the spring clamp on the block E. is used to hold the 8 in. D E 8 in. 6 in -6 in.- 6 in.
The below shows an asrag arrangement of objects 7igure in equlibrium. The Block A has a weight of 40.0N, blbck B has weight 07 SO.ON Ppe in the centre, Te, is horizantal and ☺ = 35° q. Calulate tensian I T3 A
What would be the resultant force F of the triangular distributed load and its location d measured from point A. 150 lb/ft -3 ft < 5 ft 2 ft Select.one: a F-375 Ib and d = 1.67 ft b.F=300 lb and d = 2.5 ft OcF=37S Ib and d = 3.67 ft id F=750 lb and d = 3.67 ft
Assignment 1 SHACE Pnga Mo. Unit 1: Resolution & Cotapo sition df forces 5 erts , A Jeansmission cable aforce f 3:2 KN on the polo in पर Vत्र ABex l 3.2 KN on the pole én for able at A as shouon n the direction o the fangent to the figuer. The pyole is kept vertical ky mians f quy sope AC.Determine the tencion in the forco exlitedon the tha e guyrepe pale गपतही। =LSप्ी 8.2KN Teacher's Signature
The figure shows the Russel fracture traction device and a mechanical model of the leg. The leg is held in balance in the position indicated by the two weights attached to the two cables. The combined weight of the leg and cast is W=180 N. The horizontal distance between points A and B where the cables are attached to the leg is L=100 cm and the vertical distance is d=5 cm. Point C is the center of gravity of the cast and leg at three quarters of the L measured from point A (3L/4= 75 cm). The angle that cable 2 makes with the horizontal is measured as β=30°. Accordingly, in order for the leg to remain in balance in the shown position; a) Find the tensile force T1 in cable 1. (Write your result in N) Answerb) Find the tensile force T2 in cable 2. (Write your result in N) Answerc) Find the angle α of cable 1 with the horizontal. Response