Consider a pn junction diode with the acceptor concentration as 10 cm, donor concentration as 10* cm°, intrinsic concentration as 10" cm, the cross section area is 400 um.er 11.7, co = 8.854*10*" F/m, reverse saturation current = 10 pA and T = 50 Deg C. Calculate depletion width and depletion capacitance of the diode shown in Figure 1. +12V +9V Figure 1

Consider a pn junction diode with the acceptor concentration as 10 cm, donor concentration as 10* cm°, intrinsic concentration as 10" cm, the cross section area is 400 um.er 11.7, co = 8.85410" F/m, reverse saturation current = 10 pA and T = 50 Deg C. Calculate depletion width and depletion capacitance of the diode shown in Figure 1. +12V +9V Figure 1

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

Consider a silicon pn junction diode at T 300K. The reverse saturation current is Is = 10-14 A and the ideality factor n = 1. Determine the diode current for a diode voltage of VD = 0.573 V and use that to determine the DC and AC resistance of the diode. RDC = 14.13 k rac = 639 Q RDC = 234 Q2 = rac=8Q RDC = 7.00 KQ rac = 307 Q RDC = 1.43 kQ rac = 58 Q
In a p+-n junction diode, if the minority carrier recombination rate is increased by 100 times, how will the diode current change (in magnitude)? (a) Only the forward current will increase. The reverse current will not change. (b) Only the reverse current will increase. The forward current will not change. (c) Both the forward and reverse current will increase. (d) Both the forward and reverse current will decrease. Solution: (c)
Consider an abrupt junction PN diode with Na = 5x105 cm-3 and Nd = 2x10" cm-3 at T=300K. What is the applied bias voltage for high level injection?
Considering a clamper circuit, where capacitance C, load R, the cut-in voltage of diode are unknown, which is the correct statement 1- the dc level of the signal changes 2- the peak-to-peak value of signal changes 3- the shape of signal changes 4- the dc level shifts up 5- the dc level shifts down
A silicon diode has a reverse saturation current of 50nA at room temperature (25degrees centigrade). If the operating temperature is raised by 50-degrees centigrade, what is now the reverse saturation current?
Compute the value of DC resistance and AC resistance of a Germanium junction diode at 250C with reverse saturation current, I0 = 25µA and at an applied voltage of 0.2V across the diode.
A pn junction diode has a reverse saturation current of 100nA at ajunction operating temperature of 28°C. What is the forwardcurrent when the forward bias voltage is 0.5V and the dynamic acresistance at that current? (Solution: Dynamic ac resistance =1.0x10-3ohm)
A silicon diode is in connected to a DC voltage source with Forward biased, the net currentflowing through the diode is (25mA) where the applied voltage across the terminals of thediode is (820mV). Determine diode temperature, if Is "dark saturation current", the diodeleakage current density in the absence of light is 3.4 × 10−10 A
Make the described voltage multiplier circuit, determine the voltage charge in each capacitor, and the output voltage of the circuit. Plot the output waveform in proper phase alignment with the input voltage. Indicate the peak values with the support of your solutions. Use silicon diodes in your analysis and an input V=10 Vrms. a) Half-wave voltage doubler b.) Full-wave voltage doubler
• A Si diode at a temperature of 25°C has VD = 0.7V at Is = 10nA. The temperature is raised to 125°C. 1. Calculate ID at 25°C. 2. What is effect of rise in temperature on VD & IS 3. Calculate ID at 125°C.
Given the clamper circuit below, assume that the value of R and C are large enough so the voltage across the capacitor does not change significantly during the interval of time. a. Using the simplified diode model, simulate the action of the circuit when the diode is in forward and reverse bias condition and measure its output voltage. b. Draw the output waveform of the circuit. VIN +8V ER 1.3V. -8V
For the circuit shown in the figure below, consider the diode as an ideal diode & R.M.S value of source voltage as Vs. The output voltage waveform at R is most likely to have zero value in the positive half cycle and a peak value of 1.414Vs in the negative half суcle sine-wave nature with a peak value 1.414VS zero value in the negative half cycle and a O peak value of 1.414Vs in the positive half сycle O sine-wave nature with a peak value Vs