Calculate the moment of inertia about the X and Y axes of the figure, considering a=P. Suggestion: create a table with the figures, according to the exercises in the book. P=17

Q: re for rotational motion about the hir m, b=0.5 m, 1-1 m, m- 10 kg. M

A: The moment about hinged point "O", (J+ml2)o..+(k2b2+k1a2)θ=Folsinωt

Q: A truss system is simply supported at A and B. If P = 174 kN, determine the absolute value of the…

A: GIVEN DATA- A PLANE TRUSS GIVEN WE HAVE TO FIND FORCE IN MEMBER EB CONCEPT USED- METHOD OF SECTION

Q: List five typical areas of engineering where the finite element method is applied.

A: There are so many areas of engineering where finite element method is applied. The typical five…

Q: The strain components εx, εy, and γxy are given for a point in a body subjected to plane strain.…

A: The detailed stepwise procedure to solve this problem is shown in the following attached image:

Q: An L-shaped elastic member ABC with slender arms AB and BC of uniform cross-section is clamped at…

A:

Q: I need the answer as soon as possible

A: Given:  d = 40 mm r = 20 mm h = 30 W/m2-K k = 0.5 W/m-K

Q: shear and moment diagram

A: ∑M2=0R1*12-40*4*10-20*8*4-40*4=0R1=240012=200kN ∑Fy=0R1+R2=160+160+40R2=160kN

Q: Maximize subject to P = 30x1 + 40x2 2x1 + x₂ ≤ 10 x1 + x₂ ≤7 x1 + 2x2 < 12 X1, X20

A:

Q: (B):-During corrosion tests, current density of 0.86 Amp/m² was measured for steel sample immersed…

A: Current Density, i = I/A = 0.86 Amp/m2 = 0.86×10-4 Amp/cm2 density, ρ = 7.87 g/cm3 molecular weight,…

Q: The frame is loaded as shown. The 150 lb/ft distributed load is perpendicular to member AC. The…

A:

Q: In flow separation, wake is defined as the region of flow trailing the body where the effects of the…

A: as per guideline  i have to solve only three subpart of your question given = choose true or false

Q: A 500kg container van is being lowered into the ground when the wire rope supporting it suddenly…

A:

Q: In a Porter governor, the upper and lower arms are each 250 mm long and are pivoted on the axis of…

A: Given that: length of each arm of the Porter governor is 250 mm Mass of rotating ball = 3kg Mass of…

Q: Q3: Explain how you would produce a hard surface in the followings, Give reason(s) for your…

A: Q3. Explain how you would produce a hard surface in the following, Give reasons for your selection…

Q: Determine the internal forces and bending moment at point C. Express these based on the sign…

A: To find: Internal forces at point C = ? internal bending moment at C = ?

Q: An automobile weighing 4000 lb is accelerated at the rate of 3ft/s^2 along a horizontal roadway.…

A:

Q: The x-coordinate of a particle in curvilinear motion is given by x = 4.1t3 - 3.1t where x is in feet…

A:

Q: 2. A stone is thrown with an initial velocity of 100 m/sec upward at 60⁰ with the horizontal,…

A:

Q: The force of attraction between 2 particles of masses 250 kilograms and 50 kilograms respectively is…

A:

Q: Calculate the magnitude of the tension T and the angle 0 for which the eye bolt will be under a…

A:

Q: Calculate Discharge through a horizontal Venturi meter for following given data: Diameter of pipe=…

A: Given data as per the question Diameter of pipe =1 m Diameter of throat =0.2 m The difference in…

Q: In an epicyclic gear of the sun and planet' type has a fixed outer wheel A, sun wheel S driven. The…

A:

Q: A construction vehicle has a diesel engine with 8 cylinders of 5.375in bore and 8in stroke,…

A: *As per our guidelines we are supposed to answer first three sub-parts of the question. Kindly…

Q: Draw the load and moment diagrams. V (lb) 300 -360 -780 3- 600 -x (ft)

A:

Q: Q7: An air conditioning system is used to maintain a house at a constant temperature of 20 C. The…

A:

Q: A flywheel 6 ft in diameter accelerates from rest at a constant rate of 4 rpm per sec. Compute the…

A: Diameter, d = 6 ft Acceleration, α = 4 rpm/sec Time, t = 10 sec ωo= 0   To-Determine:- a. Normal -…

Q: 1 (B):-During corrosion tests, current density of 0.86 Amp/m² was measured for steel sample immersed…

A: Given: current density, j =  0.86 Amp/m2 = 0.86×10-4 Amp/cm2 molecular weight, M = 55.8 g/mole…

Q: Prob. 2.9-8. The steel eyebar in Fig. P2.9-8 has cross-sec- tional dimensions 25 mm x 100 mm. To…

A: Introduction: The amount of deforming force delivered per unit area of an item is referred to as…

Q: Materials with dislocations have lower shear strengths than materials with no dislocations. Is this…

A: Dislocation: It is a linear crystallography defect inside the crystal structure of the material…

Q: 5. The arms of a Porter governor are 300 mm long. The upper arms are pivoted on the axis of rotation…

A: Introduction: The two balls of a porter governor are pivoted at the top to allow for vertical…

Q: 4. A scuba diver encounters a shark at 40 m depth, she panics and climbs up to the surface very…

A: Question NO. 2: Answer: E. Henri Pitot He created a tube with an opening that faced the flow that…

Q: Initially at rest, a gear starts rotating with a constant angular acceleration a = 5 rad/s². What is…

A: Introduction: A pseudoscalar, angular acceleration, exists. If the angular speed rises…

Q: 3 A force F of magnitude 50 N is exerted on the auto- mobile parking-brake lever at the position x =…

A:

Q: Question 15 What is the Ideal Gas Law and what does each letter represent?

A: Ideal gas law is the equation which approximate the behaviour of several gases

Q: (B):-During corrosion tests, current density of 0.86 Amp/m² was measured for steel sample immersed…

A: Given data: Current density, j = I/A = 0.86 Amp/m2  Molecular weight of the steel, M = 55.58 g/mole…

Q: Bar ABD in Figure P3.1 06 is supported by a hinge at B and by a cable at A. Find (a) the tension in…

A:

Q: NCLUDE DETAILED CALCULATION AND EXPLANATION Suppose you are a group of cadet engineers given by…

A: A flow metre is a tool that gauges a fluid's flow rate. The linear, nonlinear, mass, or volumetric…

Q: You are part of a team that is completing a mechanical-engineering project. Your team built a steam…

A:

Q: Consider the beam shown in (Figure 1). Suppose that F₁ = 4.2 k, F₂ = 8.4 k, F3 = 2.8 k, and F₁ = 5.6…

A: Given Data The force 1 acting on the beam is: F1=4.2 k The force 2 acting on the beam is: F2=8.4 k…

Q: ynamics of Rigid Bodies A couple M = 2( θ^3) - ( θ) is applied to a shaft that rotates from 0-90…

A: Given:M=2θ3-θθ1=90=π2θ2=0

Q: The figure below shows a frustum of a cone with an orifice in the bottom of 2,000 cm² area. Assume C…

A: Solution  Given data- C = 1.0                       a = 2000 cm2 = 0.2 m2

Q: Problem 4 - Frames & Machines The gripper shown to the right has a broken torsion spring at point C…

A:

Q: Q1:A/Solve the following linear programming problem using the graphical method Min (Z)= 20X+30Y…

A: Minimize Z = 20X + 30Y Subjected to X + 2Y ≥ 6 4X + 2Y ≥ 12 6X + 2Y ≥ 15 X ≥ 0, Y ≥ 0 X + 2Y ≥ 6…

Q: Find the scale of force when (F=400 N, (L_MN = 9.49 mm

A: Given:F=400 Nlenth of scale, L=9.49 mm

Q: A four-cylinder, two stroke cycle diesel engine with 10.9cm bore and 12.6cm, stroke produces 88kW of…

A:

Q: Calculate the magnitude of the resultant force on the indicated area on the gate and the location of…

A:

Q: The drag racer P starts from rest at the start line S and then accelerates along the track. When it…

A: Given that: When the racer traveled 120 m, speed is 40 m/s and acceleration is 11.4 m/s2 It is…

Q: A spherical steel ball bearing has a diameter of 2.540 cm at 23.00 C. (Assume the coefficient of…

A:

Q: A flat plate made of cast iron is exposed to a solar flux of 600 W/m² at an ambient temperature of…

A:

Q: Determine the resultant R (single equivalent force) of the three forces acting on the simple truss.…

A:

Moment of Inertia

Inertia can be termed as a resistance offered by a body to change its state. A rigid body initially at rest will apply resistance when acted by an external force that tends to change its state of rest or velocity, or a body initially at motion will provide resistance in changing its state of velocity or motion for coming to a state of rest. In other words, Newton's first law of motion describes the law of inertia of a rigid body.