Calculate the mean free time of an electron having a mobility of 1000 cm?/V-s at 300 K; also calculate the mean free path. Assume m.- 0.26 mo in these calculations [m. -0.91x100 kg] (0.148 ps, 33.7 nm) O ( 148 ps, 33.7 nm) O (1.48ps, 3.37 nm) O (14.8 ps, 33.7 nm) O

Calculate the mean free time of an electron having a mobility of 1000 cm?/V-s at 300 K; also calculate the mean free path. Assume m.- 0.26 mo in these calculations [m. -0.91x100 kg] (0.148 ps, 33.7 nm) O ( 148 ps, 33.7 nm) O (1.48ps, 3.37 nm) O (14.8 ps, 33.7 nm) O

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

3. Let E = (-2)x+ây +5₂ V/m and calculate (a) VPQ given P(-7,2,1) and Q(4,1,2) (b) Vp if V = 0 at Q (c) Vp if V = 0 at (2,0,-1)
One description of the potential energy of a diatomic molecule is given by the Lennard–Jones potential, U = (A)/(r12) - (B)/(r6)where A and B are constants and r is the separation distance between the atoms. For the H2 molecule, take A = 0.124 x 10-120 eV ⋅ m12 and B = 1.488 x 10-60 eV ⋅ m6. Find (a) the separation distance r0 at which the energy of the molecule is a minimum and (b) the energy E required to break up theH2 molecule.
Re 14.4 V 11.4 V Rg 8 kohm 12 kohm 12 V 20 V le(mA) A !g-1.425 mA Vee(Volt) Answer the questions given below, since they are taken from the circuit next to the output chart given above a) What common transistor configuration is the given circuit diagram? b) what type is the given transistor? NPN or PNP? Specify
A charge distribution with spherical symmetry has density = [' Pv Po₂ 0, 0≤r≤R r> R Calculate energy with p.V du equation. PV dv
C2 C4 The values of the components are as follows: • C; = 3.36 µFarads • C2 = 4.55 µFarads C3 = 6.22 µFarads • C4 = 9.25 µFarads • V = 9.71 Volts Fill in all the values into the table below: V (V) Q (µC) U (µJ) Element C (μF) C1 C2 C3 C4 CA Св Сс
3. For a Si bar of length 5um, doped n-type at 3x10¹ cm³, calculate the current density for an applied field of 3V across its length. Then do the same for a voltage of 3200V. You can assume that the electron and hole mobilities are 1500 and 500 cm²/V.s, respectively, in the ohmic region below 10¹V/cm and. For higher fields, both electrons and holes have a saturation velocity of 107cm/s.
Question 1 a) Ina closed circuit, an electric current of intensity i goes through a resistor of resistance R. The electric potential at the edges of R is measured to be V. If now we write R would this generally bethe definition ofthe resistance quantity R, or the expression of Ohm's Law? Explain. b) We define the resistivity (via the familiar notation) as E p= Thus show that the resistance R can be written as, R =p- here Lis the length ofthe resistor, and A is the cross-sectional area ofit. c) Let J the curent density (i/A). Express J in tems of the electron density n (electrons/m), the electron drift velocity va, and the electron charge e. d) Show that the resistivity can be expressed (via the familiar notation) as, m p= ne't here m is the electronmass; t is the period of time that elapses between two subsequent collisions, the electron undergoes with copper nuclei throughout its chaotic motion in the body of copper (supposing that the current carrying cable is made of copper). Hint:…
A poorly designed electronic device has two bolts attached to different parts of the device that almost touch each other in its interior as shown. The steel and brass bolts are at different electric potentials, and if they touch, a short circuit will develop, damaging the device.The initial gap between the ends of the bolts is d = 5.0 μm at 27°C. At what temperature will the bolts touch? Assume the distance between the walls of the device is not affected by the temperature change.
A conductive wire has a conductivity of ( 0.649 × 10^-8) at room temperature are ( 5.8 x 1028) conduction electron/m.calculate the mobility,resistivity and relaxation time of electrons
Cylindrical-conductors has inner and outer radii of 25 mm and 50 mm, respectively. If V(p = 25 mm) = 0 V and V(p = 50 mm) = 300 V, ɛr = 15 %3D calculate : a. V, E, and D at p = 40 mm b. Ps on each plate. %3D
Una barra esta empotrada en su extremo A, tiene una fuerza de 15 kN en el punto B y otra fuerza de 91 kN en el punto C. Determine la elongación o contracción en la barra AC, en mm, positivo para elongación y negativo para contracción. A = 0.0035 m² E = 200 GPa C A -5 m- 2 m B
Q2. Consider the general form of the frequency dependent relative permittivity of a medium: €,(w) = 1+ Etiw Ng², Tmeo (a) How does the above expression get modified if we assume that all the electrons have same natural frequency of oscillation? (b) Under the assumption made in part (a) and considering just one molecule per volume, plot the real and imaginary parts of €, as functions of frequency of the applied electric field. (c) Show that under certain assumption, the relative permittivity of a metal can be written as: e, (w) = (1– (d) What is the physical interpretation wp for a metal?