Before Fuel Injection. Some automobile engines (mainly older ones) use a carburetor to turn the liquid fuel into vapor and mix it with air for combustion. The basic principle of carburetion is shown in Figure P10.82. A piston moves down in the cylinder thereby moving air from the outside through the carburetor by way of an air filter and into the carburetor. The filtered air enters from the left of Figure P10.82 and moves into the main intake, a tube of diameter 4.2 cm, with velocity v = 8 m/s. The air must pass through a region of the intake that has a smaller diameter. Determine what diameter would be needed cause a change in pressure such that fuel from the reservoir is pulled into the airflow. The surface of the fuel in the reservoir is h = 35 cm below the bottom of the intake and the density of the fuel is 0.46 that of water. Use 1000 kg/m^3 for the density of water and 1.29 kg/m^3 for the density of air. Submit Answer Tries 0/5 Patm d₂ = ? To combustion chamber Fuel (gasoline)

Before Fuel Injection. Some automobile engines (mainly older ones) use a carburetor to turn the liquid fuel into vapor and mix it with air for combustion. The basic principle of carburetion is shown in Figure P10.82. A piston moves down in the cylinder thereby moving air from the outside through the carburetor by way of an air filter and into the carburetor. The filtered air enters from the left of Figure P10.82 and moves into the main intake, a tube of diameter 4.2 cm, with velocity v = 8 m/s. The air must pass through a region of the intake that has a smaller diameter. Determine what diameter would be needed cause a change in pressure such that fuel from the reservoir is pulled into the airflow. The surface of the fuel in the reservoir is h = 35 cm below the bottom of the intake and the density of the fuel is 0.46 that of water. Use 1000 kg/m^3 for the density of water and 1.29 kg/m^3 for the density of air. Submit Answer Tries 0/5 Patm d₂ = ? To combustion chamber Fuel (gasoline)

Name: Before Fuel Injection. Some automobile engines (mainly older ones) us
Uploaded: 2024-03-20T06:51:10.000Z
Channel: Bartleby
Description: Before Fuel Injection. Some automobile engines (mainly older ones) use a carburetor to turn the liquid fuel into vapor and mix it with air for combustion. Thebasic principle of carburetion is shown in Figure P10.82. A piston moves down in the cylind

Physics for Scientists and Engineers: Foundations and Connections

1st Edition

ISBN:9781133939146

Author:Katz, Debora M.

Publisher:Katz, Debora M.

Chapter15: Fluids

Section: Chapter Questions

Problem 76PQ

See similar textbooks

Similar questions

When a person sits erect, increasing the vertical position of their brain by 36.0 cm, the heart must continue to pump blood to the brain at the same rate. (a) What is the gain in gravitational potential energy for 100 mL of blood raised 36.0 cm? (b) What is the drop in pressure, neglecting any losses due to friction? (c) Discuss how the gain in gravitational potential energy and the decrease in pressure are related.
(a) How high will water rise in a glass capillary tube with a 0.500-mm radius? (b) How much gravitational potential energy does the water gain? (c) Discuss possible sources of this energy.
A manometer containing water with one end connected to a container of gas has a column height difference of 0.60 m (Fig. P15.72). If the atmospheric pressure on the right column is 1.01 105 Pa, find the absolute pressure of the gas in the container. The density of water is 1.0 103 kg/m3. FIGURE P15.72
A cylindrical tank, shown in the figure, has height 8 m and radius 5 m. a. If the tank is full of water, how much work is required to pump the water to the level of the top of the tank and out of the tank? Use 1000 kg/m³ for the density of water and 9.8 m/s² for the acceleration due to gravity. b. Is it true that it takes half as much work to pump the water out of the tank when it is half full as when it is full? Explain. 5 m 8 m
Ed and his friends Edd and Eddy are building a launcher to throw metal slugs up into the air. A 1.35 kg metal cylinder is placed inside the top of a plastic tube, the lower end of which is sealed off by an adjustable plunger and comes to rest some distance above the plunger. The plastic tube has an inner radius of 2.00 cm and is frictionless. Neither the plunger nor the metal cylinder allows any air to flow around them. If the plunger is suddenly pushed upwards, increasing the pressure between the plunger and the metal cylinder by a factor of 1.25, what is the initial acceleration of the metal cylinder? Assume the pressure outside of the tube is 1.00 atm.
A conical container of radius 5 ft and height 20 ft is filled to a height of 16 ft of a liquid weighing 62.4 lb / ft. a. How much work will it take to pump the contents to the rim? b. How much work will it take to pump the liquid to a level of 4 ft above the cone's rim? a. Let y = 0 correspond to the bottom of the tank. Set up the integral that gives the work required, in ft-lb, to pump contents to the rim. w= Ody The amount of work required to pump the liquid to the rim of the tank is (Round to the nearest whole number as needed.) b. Let y = 0 correspond to the bottom of the tank. Set up the integral that gives the work required, in ft-lb, to pump the liquid to a level of 4 ft above the cone's rim. W = |dy The amount of work required to pump the liquid to a level 4 ft above the rim of the tank is (Round to the nearest whole number as needed.)
A hand-driven tire pump has a piston with a 2.00 cm diameter and a maximum stroke of 25.0 cm. a. How much work (in J) do you do in one stroke if the average gauge pressure is 2.40 ✕ 105 N/m2 (about 35 psi)? b. What average force (in N) do you exert on the piston, neglecting friction and gravity?
A water tank is shaped like an inverted cone with height 6 m and base radius 1.5 m (as shown). a. If the tank is full, how much work is required to pump the water to the level of the top of the tank and out of the tank? b. Is it true that it takes half as much work to pump the water out of the tank when it is filled to half its depth as when it is full? Explain.
(a) Determine the work done on a fluid that expands from i to f as indicated in Figure P12.10. (b) How much work is done on the fluid if it is compressed from f to i along the same path?
A water trough has a semicircular cross section with a radius of 0.3 m and a length of 1 m (see figure). a. How much work is required to pump the water out of the trough (to the level at the top of the trough) when it is full? Use 1000 kg/m³ for the density of water and 9.8 m/s² for the acceleration due to gravity. b. If the length is doubled, is the required work doubled? Explain. c. If the radius is doubled, is the required work doubled? Explain. 1 m 0.3 m
Which statement is incorrect about gases, liquids, and solids? O Gases and liquids flow so they are both fluids. O Liquids and solids are hard to compress. O All these statements are incorrect. O Solids and gases take the shape of containers they arc in.
The aorta is the main artery from the heart. I typical aorta has an inside diameter of 1.8 cm and can carry blood at a speed of 35 cm/s. What is the speed of blood at a point in the aorta where the artery has had its diameter reduced by 50% from build up of plaque.