Page 6 of aAnother name for "SIZE DESCRIPTION" is:A Dimensioning.B Orthographic projection.C Assembly drawing.D Pictorial drawingWhat is the length to width ratio of arrowheads?A 1:13742в 2:1С 3:1D 5:1Leader lines should NOT be drawn:38"2X on a hole note means:43A At 45°.A Double the size of the hole.B At 30°.C At 60°.D Horizontally or Vertically.B Reduce the stated size by 1/2.C The scale of the hole is doubled.D There are two boles the same size.Extension lines are drawn:39Avoid dimensioning to:44A Extremely thick,A Hidden lines.B Thick.B Center lines,C Thin.D Extremely light.C Extension lines.D Holes.What is the standard length for arrowheads?CIRCLE SIZE is specified by:4540A 031 (.5mm)B 063 (Imm)A Chord.B Circumference.C Diameter.C. 125 (3mm)D 250 (6mm)D Radius.Dimension lines should be:4146The size of an ARC is typically specified by its:A Thick and dark.A Diameter,B Thick and light.B Circumference.C Chord.C Thin and dark.D Thin and light.D Radius.Go on to next page

Given Engineering drawing To find Size description Leader line Extension line

Another name for "SIZE DESCRIPTION is: 37 A Dimensioning B Orthographic projection. C Assembly drawing D Pictorial drawing Leader lines should NOT be drawn: 38 A At 45. B At 30. C At 60. D Horizontally or Vertically. Extension lines are drawn: 39 A Extremely thick. B Thíck. C Thin. D Extremely light.

Another name for "SIZE DESCRIPTION is: 37 A Dimensioning B Orthographic projection. C Assembly drawing D Pictorial drawing Leader lines should NOT be drawn: 38 A At 45. B At 30. C At 60. D Horizontally or Vertically. Extension lines are drawn: 39 A Extremely thick. B Thíck. C Thin. D Extremely light.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3. GEOMETRY OF TECHNICAL DRAWING-TANGENCIES DDRAW TANGENT TO CIRCLE AT POINTP AND TANGENT FROMQ TO LOWER PORTON OF CIRCLE. 2 DRAW ARC TANGENT TO LINE AB AT B, AND THROUGH POINT C. A B DRAW ARC OF 30mm (1.20") R TANGENT TO GIVEN LINES SHOW CONSTRUCTION FOR POINTS OF TANGENCY. DRAW ARC OF 50 mm (2.00")R TANGENT TO GIVEN LINES. SHOW CONSTRUCTION FOR POINTS OF TANGENCY. DRAW ARC OF 30mm(1.20")R TANGENT TO GIVEN LINE 5 DRAW ARC OF 38 mm(1.50")R TANGENT TO GIVEN UNES. SHOW CONSTRUCTION FOR POINTS OF TANGENCY. 6. AND ARC. SHOW CONSTRUCTION FOR POINTS OF TANGENCY. 1.
Draw the SECTION VIEW for Figure 1 with the scale 1:1 on the new drawing paper using all the method on section. Dimension must be included. All dimension in mm. You are require to draw again the top view and then A-A section.
Draw front and right-side views of the following object with a completed dimensions. Draw in scale 1:1 on A4 sheet. (Problem is taken from "Graphics for Engineers' by Earle) 78 What can we learm from the drawlng ? 1. The dimension note M10x1.5 means that the hole is a threaded hole. R16 O 16, 2 Holes The letter 'M' means that the threads are made by following a metric thread system. The number "10" Is the major dlameter of the hole and the number 1.5 is the pitch of a thread. However, for coarse threads, it is a common practice to omit specifying the pitches. For example, a note M10 means the pitches of the thread is 1.5 mm. In this book, the pitch is specified in order to facilitate drafting. 2. Drawing symbol of a threaded hole is shown below. - Thin Ine (4H pench The ends of this arc does not meet together but approximately 90 degs, apart. Object Ihe (2i pencil .major dlameter pich2 M10x1 5 3. The circular projection surface at a threaded hole that is raised from a cylinder is…
The below figure shows two views of a bolster block. Draw, using 1 st angle projection and a suitable scale, the following views: (a) the given front elevation; (b) a sectional end elevation taken on the cut-ting plane A-A; (c) the given plan; (d) an isometric view of the block. Show all hidden details. Print title, scale and show six leading dimensions Note : use creo parametric to solve the answer
Draw the 3rd angle orthographic projection and isometric drawing.
Create the following drawing in autocad. Please show Layers and Dimensions.
Plz Answer Both The Questions To make the circle in an Isometric drawing which geometric option we select from menu bar and why? When saving an AutoCAD drawing what is the name of its file extension?
a= 15.0 in, b= 7.0 in, c= 12.0 in, and d= 12.0 in.,(e= 3.0 in. horizontal), Draw the kinematic diagram in SolidWorks drawing sheet with size A3 iso and suitable scale. Solve the following questions and upload the SolidWorks file below. e d. Is the mechanism grashof? Select one: True False
Draw velocity polygon.
II. Arrange the following steps/procedures in sketching Oblique Drawing. Write number 1-7. Copy and Answer on your answer sheet. ______ Check your drawing for accuracy. ______ Draw the horizontal and vertical axes. ______ Draw the surface in orthographic form using the vertical and horizontal axes as base lines. Get your measurement from the given orthographic view. ______ Determine the side or surface to be made parallel to the picture plane. ______ Draw the cross-axis. Use 45 degrees in the plane of projection. Connecting points. ______ Draw all visible edges. ______ Lay out the measurement along the cross-axis, take note the difference of the cabinet and cavalier drawing. Completing the details.
Test-II. Write down all the operations or step by step procedure on how to create the object below. Write down also the name of the machines and the tools that you will use to complete the drawing below. 824 020 015 22 15 35 40 100 NOTE: ALL DIMENSIONS ARE IN MM ALL CHAMFERS ARE 1X 45
F, = 50 N F2 = = 40 N -5 45° F1 = 20 N