An impedance oil takes 144 watts at a lagging factor of 0.6. What values of capacitance and resistance should be connected in series with the coil if the power input to the latter is to remain unchanged and the overall circuit is to be unity? The circuit is energized by a Voltage of 120 v and frequency is 60Hz

An impedance oil takes 144 watts at a lagging factor of 0.6. What values of capacitance and resistance should be connected in series with the coil if the power input to the latter is to remain unchanged and the overall circuit is to be unity? The circuit is energized by a Voltage of 120 v and frequency is 60Hz

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter26: Three-phase Circuits

Section: Chapter Questions

Problem 3PA: You are an electrician working in an industrial plant. A 30-hp three-phase induction motor has a...

See similar textbooks

Similar questions

A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating of 600 WVDC. The capacitor and resistor are connected to a 480-V, 60-Hz circuit. Is the voltage rating of the capacitor sufficient for this connection?
What is the minimum AC voltage rating of each capacitor in Question 11?
You are an electrician working in an industrial plant. A 30-hp three-phase induction motor has a current draw of 36 amperes at full load. The motor is connected to a 480-volt line. A three-phase wattmeter indicates a true power of 22 kW. Determine the power factor of the motor and the amount of capacitance needed to correct the power factor to 95. Also determine the minimum voltage rating of the capacitors. The capacitors are to be connected in wye.
An RC series circuit is connected to a 120-V, 60-Hz power source. The resistor is 25 and has a voltage drop of 65 volts. What is the capacitance of the capacitor?
Value of series impedance if inductance is 4mH , resistance is 40 ohm and frequency is 50 Hz.
A 206.0-2 resistor and a 2.80-µF capacitor are connected in series across the terminals of a sinusoidal emf with a frequency of 150 Hz. The inductance of the circuit is negligible. What is the impedance of the circuit?
60. Design a circuit to limit a 20 V rms sinusoidal voltage to a maximum positive amplitude of 10 V and a maximum negative amplitude of -5 V using a single 14 V de voltage source. 61 Datermine the volto in the girRuit F Figura 1 1?
QUESTION 3 An inductor and a 330 ohm resistor are connected in series with a function generator. The current is 89.8mA RMS 5kHz. The reactive power is 3.04 var. Find the value of the inductance. O 12mH O 24mH O 6mH O 18mH
Q4. Determine the equivalent inductance and equivalent current of the inductive circuit in Figure Q4. If L5 is replaced with a capacitor of 0.5 mF, how would it affect the branch current? The alternating Voltage source has an amplitude of 20 Vm. Vm Sine 50 Hz L1 5 mH L2 3 mH Figure Q4 reee L3 6.6 mH L4 2.8 mH rele L5 7 mH
How does the equivalnce capacitance in series vs parallel relate to the dimming time of a bulb.
A 50 ohms resistor, an 80 ohms inductive reactor, and a 60 ohms capacitive reactor are connected in parallel across 240 volts 60 cycles mains. Determine a) total current; b) power factor; c) power; d) To what value of capacitance should the capacitive reactor be adjusted to give antiresonance?A 25 ohms resistor, a 0.05 henry inductor, and an adjustable capacitor are connected in parallel across a 100 volts 120 cycles supply. Determine: a) capacitance to make the circuit antiresonant; b) current to inductor and to capacitor; c) power.
How did they get sin and cos term?