An external drive system actuates the mechanism by applying a moment M at bearing D. At the instant 0 60°, the magnitude of the velocity vector of point C is 12 m and the angular acceleration of link CD is 30 rad. in the CCW direction. Determine the x-component of the acceleration vector of point C in 4 at this instant. Consider L 8 metres. E Your Answer: Answer

An external drive system actuates the mechanism by applying a moment M at bearing D. At the instant 0 60°, the magnitude of the velocity vector of point C is 12 m and the angular acceleration of link CD is 30 rad. in the CCW direction. Determine the x-component of the acceleration vector of point C in 4 at this instant. Consider L 8 metres. E Your Answer: Answer

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter1: Introduction To Statics

Section: Chapter Questions

Problem 1.47P: A rifle at A is fired at a target at B. If the speed of the bullet is 1400 ft/s, determine the...

See similar textbooks

Similar questions

Using Vector Amelysis find angular velority and 28° accelration of cB and AB snguler 37.8in Vebmis given Velocity of C=5 m/s 30° 11 in
An external drive system actuates the mechanism by applying a moment M at bearing D. At the instant 0 = 30°, the velocity of point C is 14 m (upward to the left) and the angular acceleration of link CD is 45 rad in the CCW direction. Determine the x-component of the velocity vector of point G in m at this instant. Consider L 4 metres. E B y M.
2. For the linkage system shown, determine the velocity vectors of points B and C. 6 rad/sec A B 0.3 m 0.2 m 0.35 m 40⁰ D
Find the acceleration of the translating piston at the given instant if w1 = 10 rad/s And a, = -5 rad/s² . Present a, vector 13 in. BAR 2 form. rad/s² az in/s² w1 = 10 rad/s a1 = -5 rad/s² -BAR 1
WA TB RA
2) At a given moment four Link mechanism OA BO, , Is in the position shown onthe figure and OA = AB = A0, = 3V2 m.Link OA rotates of constont angular ve locity W,= 5 s-1. Find the values of angulor velocity Wg and angular acce leration Es of link O, B. 10 1450
An external drive system actuates the mechanism by applying a moment M at bearing D. At the instant 0 = 55°, the magnitude of the velocity vector of point C is 19 m and the angular acceleration of link CD is 30 rad in the CCW direction. Determine the angular velocity vector of link CE (in L = 2 metres. rad :) at this instant. Consider E y +. • Ch
The rod OA rotates clockwise at a constant angular velocity of 0 = (3) rad -. Two pin-connected slider block, located at B, move freely on OA. The curved rod is described by the equationr = (250 · (8 - cos 0)) m. Hint: 1. Remember clockwise rotation is negative velocity. A d3 d1 d2 Values for the figure are given in the following table. Note the figure may not be to scale. Variable Value 01 130 degrees di 0.45 m d2 dz 0.2 m 0.325 m Using cylindrical components, a. Determine the cylinders's radial and transverse components of velocity at the instant shown, vr and b. Determine the cylinders's radial and transverse components of acceleration at the instant shown, a, and ag. c. Determine the cylinder's magnitude of the velocity at the instant shown, v d. Determine the cylinder's magnitude of the acceleration at the instant shown, a
As shown in the figure, the right-angled bar OAB rotates uniformly around the O-axis, and the angular velocity is w. AB is fitted with a small ring M, which is also fitted with a large fixed ring. At the moment shown in the figure,OMO1 is on the same horizontal line, the radius of the big ring is known as R,001=3R, and Please calculate the speed and acceleration of the instantaneous small ring 30 M B 9 R
In the mechanism shown below, the wheel is pinned at the center. The radius from O to C is 0.2 m and link CB is 0.55 m long. CB makes an initial angle of 25° with the horizontal as shown. The hydraulic ram at B is moving left at 7 m/s. At the moment shown, what is the angular velocity of link BC and the wheel pivoted at 0? 0000 Ninbet tatis rad/s
Question 6 to this answer. At the instant shown, the bar AB has a velocity of 4.8 rad/s clockwise. If a = 0.22 m, b = 0.33 m,0 = 24°, and a = 52° at this instant. Determine the magnitude of the velocity in m/s of roller C. A 0 α A
Bar AB is rotating about A with an angular velocity of wAB 2 rad/s counterclockwise. At this instant bar BC is horizontal. Find the Wac and also, velocity of collar C. Note. You must solve the problem in the way that we solved in the class. Use Vg VA+ wX TB/A and express the vectors in Cartesian vector form. Other solutions will not be evaluated. Solve the problem step by step, and clearly show your work. 25 35 mm 170 mm