air at constant pressure of 101.3kpa and 289 k enters inside a tube having an inside diameter of 19.1 mm and a lenght of 2.12m with a velocuity of 24.4m/s. condensing steam on the outside of the tube maintanis the insde wall temprature at 373.1 k knowing that the air flow is turbulent calculate the convection coefficient of the air . ( hint use the simplifiled equaation for air at 1 atm)

air at constant pressure of 101.3kpa and 289 k enters inside a tube having an inside diameter of 19.1 mm and a lenght of 2.12m with a velocuity of 24.4m/s. condensing steam on the outside of the tube maintanis the insde wall temprature at 373.1 k knowing that the air flow is turbulent calculate the convection coefficient of the air . ( hint use the simplifiled equaation for air at 1 atm)

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.34P

See similar textbooks

Similar questions

6.1 Determine the heat transfer coefficient at the stagnation point and the average value of the heat transfer coefficient for a single 5-cm-OD, 60-cm-long tube in cross-flow. The temperature of the tube surface is , the velocity of the fluid flowing perpendicular to the tube axis is 6 m/s, and the temperature of the fluid is . Consider the following fluids: (a) air, (b) hydrogen, and (c) water.
7.43 Liquid sodium is to be heated from 500 K to 600 K by passing it at a flow rate of 5.0 kg/s through a 5-cmID tube whose surface is maintained at 620 K. What length of tube is required?
6.3 Steam at 100 kPa and is flowing across a 5-cm- OD tube at a velocity of 6 m/s. Estimate the Nusselt number, the heat transfer coefficient, and the rate of heat transfer per meter length of pipe if the pipe is at .
determine the length of the tube required for fully develop flow when 9.06 kg of waterper minute is passed through a tube of 2 cm, it is found to be heated from 20 degree celsiusto 60 degree celsius, the heating is achieved by considering steam on the surface of the tube andsubsequently the surface temperature of the tube is maintained at 90 degree celsius.
Corsidera circular smoth pipeof inner diameter D;=0.015mwhose inner surface is covered with a layer of liquid as a result of condensation. In order to dry the inner surface of the pipe, air at 300K at 1 atmis forced to flow throughit with anaverage velocity of 1.2m/s. Using the analogy between heat and mass trarsfer, detemine the mass transfer coeffícient irside the pipe for fully developed flow. Note: Viscosity of the air for given conditions is given as 1.58 x 10°n?/s. Also, for a lamirar fully developed flow the N=Sh=3.66. Your solution must state governing equations and associated assumptions, illustration and step by step execution of the overall solution
Air at 1 atmosphere and a temperature of 60f enters 1/2-in. id tube with a velocity of 80 fps. The wall is maintained at a constant temperature of 210 by condensing steam. Fin the convective heat-transfer coefficient for this situation if the tube is 5ft long
3. Two parallel plates are separated by a distance 2H. The plates are moved in opposite directions with constant velocity Uo. Each plate is maintained at uniform temperature To. Taking into consideration dissipation, determine the heat flux at the plates. Assume laminar flow and neglect gravity effect. To U. Uo T.
Determine the expected Fanning friction factor for water at 28 degrees Celsius flowing through a smooth tube whose ID is 15mm, at a velocity of 0.45 m/s
Shown in the figure,a card is cooled with water. To cool the cardWater 0.4 m / s in the circular pipe system placed on the bottomaverage speed and entering at a temperature of 20 oC, at a temperature of 24 oCcomes out. Electronic components on the board of 1.5 kWthey produce energy. At the same time, from the card surface to the mediumApproximately 0.05 kW of heat loss occurs by convection. Continuous flowFind the mass flow rate of the water for the conditions. Specific heat of waterYou can get = 4.22 as ?? / ???.
Air at 1 atm and 20 C flows in a 2.5-cm-diameter tube. The maximum velocity (m/s) of air to keep the flow laminar is
You are designing a pin-style heatsink for forced cooling of an IC. A small fan blows RT air into the heatsink at about 2.3 ? ? . The aluminum pins are 2mm in diameter and have a constant surface temperature of 120°?. The heatsink is 100mm x 100mm and the pins have an inline arrangement with a transverse pitch of 4mm and a longitudinal pitch of 6mm. What is the total heat dissipation of this heatsink? The pins are 30mm high. Note RT=25 celsius
Milk is Pasteurized by first heating it to 71oC, and keeping it at that temperature for 17 seconds before cooing it rapidly for bottling. Fresh milk at 5oC enters the Pasteurization unit where it flows through a thin-walled stainless steel (SS) tube of 2.0 cm diameter. The inside surface of the tube is such that the flow is turbulent to promote good mixing and uniform temperature across the flow at every point along the tube. Heating is provided by passing the tube in a closed container that is filled with saturated steam at atmospheric pressure and 100oC. Hence, we can assume that the thin-walled SS tube temperature is maintained at 100oC all along its length by condensing steam over the outside surface. The flow-rate of milk is 40kg per minute (i.e. approximately 10 gallons per minute). a) What is the mean velocity (m/s) and ??? for the milk flowing through the tube between 1-2? b) What is the convective heat transfer coefficient h (W/m2K) over the inside surface of the tube? c) What…