Activity 1: A rectifier circuit is used to charge a 12 Vdc battery using a 40 Vp-p AC source, according to the following circuit. ĺbatt 2002 ww RECTIFIER 12 Vac 40 Vp-p (AC) (1-a) Build a half-wave rectifier circuit with a single diode to perform the charging function. Explain the operation of the diode and the entire circuit. Use drawings to illustrate how battery current changes with the input voltage. (Assume that diodes turn on at 0 V) (1-b) Build a full-wave rectifier circuit with four diodes to perform the charging function. Explain the operation of the diodes and the entire circuit. Use drawings to illustrate how battery current changes with the input voltage. (Assume that diodes turn on at 0 V) (1-c) Assuming practical diodes in the full-wave rectifier, describe the behaviour of a single diode as a p-n junction, then analyse the operation of the entire rectifier assuming 0.7-V threshold voltage for each diode. Use simulations to support your analysis.

Activity 1: A rectifier circuit is used to charge a 12 Vdc battery using a 40 Vp-p AC source, according to the following circuit. ĺbatt 2002 ww RECTIFIER 12 Vac 40 Vp-p (AC) (1-a) Build a half-wave rectifier circuit with a single diode to perform the charging function. Explain the operation of the diode and the entire circuit. Use drawings to illustrate how battery current changes with the input voltage. (Assume that diodes turn on at 0 V) (1-b) Build a full-wave rectifier circuit with four diodes to perform the charging function. Explain the operation of the diodes and the entire circuit. Use drawings to illustrate how battery current changes with the input voltage. (Assume that diodes turn on at 0 V) (1-c) Assuming practical diodes in the full-wave rectifier, describe the behaviour of a single diode as a p-n junction, then analyse the operation of the entire rectifier assuming 0.7-V threshold voltage for each diode. Use simulations to support your analysis.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
In a full wave rectifier circuit involving double diodes, a sinusoidal input signal of the following nature is applied e=10 sin(500*pi*t) V. What will be value of the dc voltage obtained at the output of the rectifier.
3 Given the bridge-type full-wave rectifier circuit shown 220V 60Hz 220V:Es Es D1 D2 D3 D4 The load resistor is 220 and the transformer average current is 300mA. Determine: (a) Average value, RMS value, and frequency of load voltage VRL. (b) Average current and PIV of each diode. RL
A single-phase full-wave bridge rectifier circuit is fed from a 220 V, 50 Hz supply. It consists of four diodes, a load resistance 20 Q and a very large inductance so that the load current is constant. What is the average or dc output voltage?
Consider the half-wave rectifier shown in the figure below. Let vs be a sinusoidal with 10V peak amplitude with frequency of 60Hz and let R = 1000 ohms. Use the contant voltage-drop diode model with VD = 0.7 V.
A sinusoidal signal with a maximum value of 12V is applied to the input of the bridge type rectifier circuit. Since silicon diodes with a threshold voltage of 0.7V are used in the circuit, what is the maximum voltage of the signal at the output of the rectifier?
Consider the circuit shown in Figure 2. The cut-in voltage of each diode is . Let and assume both diodes are conducting. Determine if this is a valid assumption and explain your answer. And calculate the values of IR, ID, Ip2, and V.. Rj =1.7 kQ ww VB =1 V D1 Dz R2D 4 kQ Figure 2
For the rectifier in the figure below, state the conduction sequence of the diodes for periods t1 to tó. D1 D2 D3 22) tl: D. & D.. 23) t2: D. & D.. 24) t3: D. & D.. 25) t4: D. & D.. D4 D5 D6 26) t5: D. &D. 27) t6: D.AN A & D....... Vm cot t6
Draw the input waveform and output waveform for the circuit given below with proper values marked in the figure. Assume D1 as germanium and D2 as silicon diodes. Input Vpp%3D20V, V1=3 V and V2=10 V. R D2 D1 Vin Vout V1 V2 Maximum voltage of output waveform Minimum voltage of output waveform Ps
Q1/ a/Draw the output voltage waveform for the bridge rectifier in this figure : 5:1 D Da 120 V ms Dy RL B/ What PIV rating is required for the diodes in a bridge rectifier that produces an average output voltage of 50 V? Q2/ Determine the minimum input voltage required for regulation to be established in the figure. Assume an ideal zener diode with Izx = 1.5 mA and V, = 14 V. lllee 幸

The PIV for each diode in a full-wave center- tapped rectifier is............. Note: Vp(out) = peak output voltage. Choose correct answer : A) Vp(out) + 0.7 V B) Vp(out) – 0.7 V C) 2Vp(out) + 0.7 V D) 2Vp(out) – 0.7 V
.Draw a full-wave rectifier circuit (using a diode bridge) and predict the output voltage signal when the input is a sinusoidal signal with amplitude 10 V (p p). Use the previous full wave rectifier to create a peak detector with a 2 V ripple.