A tungsten wire is used to determine the melting point of lead. A battery of 6.00 V is attached to the ends of this wire and a current of 2.000 A is measured at 20°C. The lead is heated until it starts to melt. The tungsten wire is placed in the environment of the melting lead and the current is measured to be 1.237 A using the same 6.0 V battery. What is the melting temperature of lead? XX Tungsten = 4.50 × 10-³ (°C)-¹. a. b. c. d. e. 132°C 157°C Comect 731°C 478°C 327°C

A tungsten wire is used to determine the melting point of lead. A battery of 6.00 V is attached to the ends of this wire and a current of 2.000 A is measured at 20°C. The lead is heated until it starts to melt. The tungsten wire is placed in the environment of the melting lead and the current is measured to be 1.237 A using the same 6.0 V battery. What is the melting temperature of lead? XX Tungsten = 4.50 × 10-³ (°C)-¹. a. b. c. d. e. 132°C 157°C Comect 731°C 478°C 327°C

University Physics Volume 2

18th Edition

ISBN:9781938168161

Author:OpenStax

Publisher:OpenStax

Chapter9: Current And Resistance

Section: Chapter Questions

Problem 70AP: A 10.00-meter long wire cable that is made of copper has a resistance of 0.051 ohms, (a) What is the...

See similar textbooks

Similar questions

A 12.0-V emf automobile battery has a terminal voltage of 16.0 V when being charged by a current of 10.0 A. (a) What is the battery’s internal resistance? (b) What power is dissipated inside the battery? (c) At what rate (in °C/min ) will its temperature increase if its mass is 20.0 kg and it has a specific heat of 0.300 kcal/kg • °C, assuming no heat escapes?
Taking R = 1.00 k and = 250 V in Figure P21.49, determine the direction and magnitude of the current in the horizontal wire between a and e. Figure P21.49
A 20.00-V battery is used to supply current to a 10-k resistor. Assume the voltage drop across any wires used for connections is negligible, (a) What is the current through the resistor? (b) What is the power dissipated by the resistor? (c) What is the power input from the battery; assuming all the electrical power is dissipated by the resistor? (d) What happens to the energy dissipated by the resistor?
A 10.00-meter long wire cable that is made of copper has a resistance of 0.051 ohms, (a) What is the weight if the wire was made of copper? (b) What is the weight of a 10.00-meter-long wire of the same gauge made of aluminum? (c)What is the resistance of the aluminum wire? The density of copper is 8960 kg/m3 and the density of aluminum is 2760 kg/m3.
(a) During surgery, a current as small as 20.0A applied directly to the heart may cause ventricular fibrillation. If the resistance of the exposed heart is 300 what is the smallest voltage that poses thisdanger? (b) Does your answer imply that special electrical safetyprecautions are needed?
When running on its 11.4 V battery, a laptop computer uses 8.3 W. The computer can run on battery power for 8.5 h before the battery is depleted. Part A. What is the current delivered by the battery to the computer?Express your answer with the appropriate units. Part B. How much energy, in joules, is this battery capable of supplying?Express your answer in joules. Part C. How high off the ground could a 75 kg person be raised using the energy from this battery?Express your answer with the appropriate units.
A typical lightning bolt may last for 0.172 s and transfer 1.05 ✕ 1020 electrons. Calculate the average current (in A) in the lightning bolt. ?A
A conducting rod with a circular cross-section (this rod is a cylinder) has a radius of 10 mm and is 2 metres long. The rod is made of aluminum, so its conductivity is 3.6 x 10' S/m. A potential difference (voltage) is applied at both ends of this rod and the current is I = 90 A. That's a lot of current! a. What is the resistance of the rod, when measured from one end to the other? b. Calculate the current density in the rod along its length. Determine the electric field amplitude at all locations within the rod. c. d. What is the electric potential difference between the two ends of the rod.
3:08 l LTE Youngstown State University Edit Friday 9:58 AM 1. A conductor of radius r, length l and resistivity p has resistance R. It is melted down and formed into a new conductor, also cylindrical, with one fourth the length of the original conductor. What is the resistance of the new conductor? (Hint: the volume stays the same) 16R a. b. 4R c. 1. d. 4 iR 16R e.
A conducting rod with a circular cross-section (this rod is a cylinder) has a radius of 1o mm and is 2 metres long. The rod is made of aluminum, so its conductivity is 3.6 x 10' s/m. A potential difference (voltage) is applied at both ends of this rod and the current is I= 90 A. That's a lot of current! a. What is the resistance of the rod, when measured from one end to the other? b. Calculate the current density in the rod along its length. . Determine the electric field amplitude at all locations within the rod. d. What is the electric potential difference between the two ends of the rod.
Silver wire has a cross-sectional area A = 2.0 mm2. A total of 9.4 x 10 electrons pass through the wire in 3.0 s. The conduction electron density in silver is 5.8 x 1028 electrons/m. What is the drift velocity of these electrons?
Shown below is a copper wire with the following characteristics: Diameter: 1.45 mm.00145m 1.45 × 10-8 m Number density of electrons: 8.47 x 1028 electrons/m³. Conductivity: 5.96 x 107 S/m a. Calculate the drift velocity (magnitude and direction) of the electrons in the wire when a current of 5.00 A is running through it. b. What direction is the current moving? c. Remembering that current density is a vector, calculate the magnitude and direction of the current density of this wire. d. Calculate the resistivity of the wire. e. Calculate the resistance of this wire if it were 10.0 m in length.