A truss is supported by a pin support at H and a roller support at G. For thegiven loading, determine the magnitude of the force in members DF, DG, EG andFG. State whether each member is in tension or compression.Hint: Using the 'Method of Sections' will make solution of this problem easier.(Sopoints)Amato15 kNAMYA6 mBC6 m5 kNDYE6 mFt6 mG-Horror|8 mODS OF சலி6225KNEx6:-:36.28kForPROFOm

Answered: Image /qna-images/answer/75634f46-ce9d-4f9e-8ef0-c88820cd4858.jpg

A truss is supported by a pin support at H and a roller support at G. For the given loading, determine the magnitude of the force in members DF, DG, EG and FG. State whether each member is in tension or compression. (Sopoints Hint: Using the 'Method of Sections' will make solution of this problem easier.

A truss is supported by a pin support at H and a roller support at G. For the given loading, determine the magnitude of the force in members DF, DG, EG and FG. State whether each member is in tension or compression. (Sopoints Hint: Using the 'Method of Sections' will make solution of this problem easier.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1. Is this truss (simple, compound or complex )truss? 2. Determine the bar force in member AF of the truss shown in the figure below: * 20kN E D 2m A в 2m K 2m G 2m 2m 1 Add File
Determine the smallest safe cross-sectional areas of members CD, Cl and CH for the truss shown. The allowable stress are 100 MPa in tension and 80 MPa in compression. Indicate tension or compression. (Draw the required FBD and answer in mm2). Fa a –– a→– a- B D |E A a F G H а 3 2 т 45 kN
The truss is loaded by concentrated forces as shown in the figure. Use E = 30 x 106 psi and A = 0.90 in² for all the members. Determine the deformation sustained by members CG and FG. 12 kips 14 kips 16 kips A B с 10 kips |-6R-|-6A 8 ft ļE 5 ft ——6 ft—6 ft--6 ft-
-5 @ 3m-15m- C F H J K ML boo I A 4@4m=16m B D G E 60 kips A For the truss shown, what is the force in member FG? B what is the force in member BE? + --D
Q2: The truss shown is supported by a pins at A and G, and subjected to discrete loads as shown in the figure. a) Determine the reaction forces at A and G. b) Use the method of sections to determine the forces in members FE, EB and BC. State whether each member is in tension or compression. G F E 2 m A B C D - 1 m 2 m 1 m 10 kN 15 kN
4 kN 4 kN 3 kN 2 kN B C D 3 m H 2'm - 5 m- -5 m- -5 m- - 5 m- Q4- The figure shows a truss that is supported at A by a pin and a roller at E. The truss is subjected to vertical forces. Determine the following: (a) check for zero-force members and identify such members (b) The Force Reactions at the supports are: Ax kN Ay kN Ey k N (c) The internal Force in member CD, FcD i . kN, specify (T) or (C) (d) The internal Force in member CF, FCF İS. . kN, specify (T) or (C) (e) The internal Force in member CD, FcG is . kN, specify (T) or (C)
The members of the truss shown below have a cross-sectional area of 10,000 mm2. Determine the stresses in members AB and AE in MPa. Indicate if the stresses are in compression or tension. -3 m- -3 m- C E 40 kN 80 kN A 6m- 3m-
Q₁: Analyze the truss shown below B с <50k 3m IMI A E 100ku EA is Constant for all members + Am X Am
2. The following the truss figure, came from your Module 1. Page 9. B D F 3 m H H. E G 30 kN 70 kN 4 panels at 4 m = 16 m But this time, All the members have a cross sectional area of 850 mm². Find the normal stress of the following members а. EF b. GH c. DF
Exercises: Determine the normal stress in each member of the truss structures. 1. All joints are ball-joints; bottom 3 joints are fixed to the floor. Material: Steel 4KN b a-b-2 cm SKN a. Y. 10100
Question 2: The bars of the truss each have a cross-sectional area of 340 mm2. If the maximum average axial stress in any bar is not to exceed 250 N/mm2, determine the maximum magnitude P of the loads that can be applied. What are the Internal load and stress in different members (Tensile and compression) 2m 2P 3m C
The truss in the figure is loaded by four external forces as shown below. Knowing that P1= 3 kN, P2-4 kN, P3-6 kN and P4=2 kN, a= 3 m and h=2 m, you are required to: h P1 P2 a H B members GH, BG, BC. I P3 G C P4 F D a --- a -- a a) Determine the reactions at the supports A and E. b) Using the method of joints, determine the forces of the members at joint A. c) Using the method of joints, determine the forces of the members at joint E. d) Using the method of sections, determine forces on members GF GC, CD. e) Using the method of sections, determine forces on P1 Note: You are required to draw the FBD and apply the equilibrium equations for each case. E