A stud wall is to be used as a bearing wall in a wood-frame building. The wall carries axial loads caused by roof dead and snow loads. Studs are 2x6 No 2 Non Dense grade Southern Pine and are located 18-in o.c. Studs have sheathing attached. Find the allowable load per lineal foot of wall if the wall height is 11 ft. CM= 1 = C= C;=1.0

A stud wall is to be used as a bearing wall in a wood-frame building. The wall carries axial loads caused by roof dead and snow loads. Studs are 2x6 No 2 Non Dense grade Southern Pine and are located 18-in o.c. Studs have sheathing attached. Find the allowable load per lineal foot of wall if the wall height is 11 ft. CM= 1 = C= C;=1.0

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A TIMBER BLOCK "B x B" mm SQUARE IS REINFORCED ON OPPOSITE SIDES BY A "B" mm AND 't' mm THICK STEEL PLATES. DETERMINE THE THICKNESS 't' SO THAT THE ASSEMBLY WILL SUPPORT AN AXIAL LOAD OF 1000 KN WITHOUT EXCEEDING A MAXIMUM TIMBER STRESS OF 12 MPa OR A MAXIMUM STRESS IN STEEL OF 350 MPa. MODULUS OF ELASTICITY OF STEEL AND TIMBER ARE 210 GPa & 7 GPa RESPECTIVELY. B t B t PROB 04
B. Beams Design WD = 26 kN/m WL = 20 kN/m 5 m-
A timber wall 50 mm wide x 50 mm deep and having a height of 3.50 m is assumed to be hinged at top and bottom. It is subjected to an axial load of 15228 N on the centroid. A uniformly distributed load is also acting along the weaker axis of its entire height. The wall is made up of Apitong wood and stresses are shown in the table (Use 80% stress grade). To be safe, the actual stress should not exceed allowable stress, Given: bending and tension parallel to grain = 16.5 Mpa modulus of elasticity = 7310 Mpa compression parallel to grain = 9.56Mpa compression perpendicular to grain = 2.20 Mpa shear parallel to grain = 1.73 Mpa Determine the following: a. the allowable compressive stress b. the allowable bending stress c. the allowable uniform load "W" it could carry
Seatwork No. 11 whole yellow sheet of paper or bondpaper A rectangular beam having a 7-m simple span is to Support a superimposed dead load of 28 kN/m and a live lood of x. The unit weight of concrete is 24 kN/m² Consider only 1 layer of reinforcements at the tension Zone. Ise Pmax to compute your area of steel. Given fc-40 MPa fg 400 MPa X= ID. No. 1000≤x≤ 2000 424 - 1000 = 1424 N/m 3950 - 2000 = 1,950 N/m
Wood planks are used on each working level. The deck width/bearer span is 5 ft.. The bearers and posts are standard pipe and the pipe material is A36 steel with a yield stress of 36,000 psi and modulus of elasticity of 29,000,000 psi. Bearers are to be located at a vertical spacing of 10 ft (largest, lowest post height). Posts are to be 7 ft oc (plank length) parallel to the building wall and 5 ft apart (bearer length) perpendicular to the building wall. There are four working levels and the anticipated scaffold loading will be med duty. A. Assuming the ultimate bending strength of the planks is 3,800 psi (apply a 4:1 F.O.S.), determine the required minimum plank thickness to the nearest 100th. B. Based on the bearer material provided, what is the minimum pipe size that can be safely used? See Appendix 2 in your textbook for steel pipe properties. C. Based on the post material provided, can a 2” standard pipe be used safely? Be sure it satisfies buckling stress conditions only.
The wood beam has a square cross section. Find the smallest allowable cross-sectional dimensions if the working stresses are 8 MPa in bending and 1.0 MPa in shear. 5 kN 2 kN • m D B F10m- 1.0 m 1.0 m -1.0 m
A 300 mm X 450 mm exterior beam is reinforced with 2 – Ø20 mm and 1 - Ø25 mm bars on the first layer of tension reinforcement (larger bar is at the middle), 2 tension reinforcement, 3 – Ø25 mm for compression reinforcement and Ø12 mm for stirrups. From analysis the depth of the tension zone is 344 mm, if the tension steel has a yield strength of 420 MPa and the compression steel has a yield strength of 414 MPa. Determine the following using all the NSCP provision (larger bar always governs the spacing) to check and layout the beam: Ø25 mm on the second layer of - A. The compressive stress in the concrete B. The depth of compression block C. Ultimate Moment Capacity of the beam
A 4-m simply supported timber beam is to be designed to carry a total uniform load of 10 kN/m including its own weight. The timber is 80% stress grade Apitong. The nominal size of the beam is 200 mm x 260 mm. Before installation, the width and depth are to be reduced by 10 mm. 7a Find the maximumshearing stress. a. 0.50 MPa C. 0.86 MPa 7b. Find the maximum bending stress. a. 12.50 MPa c. 11.20 MPa 7c. Find the maximum deflection. a. 18.43 mm C. 14.50 mm b. 0.63 MPa d. 1.20 MPa b. 8.50 MPa d. 10.11 MPa b. 25.63 mm d. 12.60 mm
Determine M for a reinforce concrete beam 16 in. wide by 32 in. deep reinforced with seven No. 10 bars (placed in two layers: five in the bottom layer, two in the top layer, with 1 in. clearance between layers). Use f = 4,000 psi and fy= 60,000 psi - 324 ith Cov. 2#10 510 1"Clr.
1.7 in 2.5 in 2.7 in T →→ 0.755 in Three wood boards, each 4.3 in. wide, are joined by the 0.755-in.-diameter bolt. If the working stresses for wood are 807 psi in tension and 1503 psi in bearing, find the largest allowable value of the force P.
The reinforced concrete cantilever retaining wall is made with 3000 psi normal weight concrete and reinforced with Grade 60 galvanized steel. the main reinforcement rests flexural stresses in the stem and is specified as #7 bars every 18 inches along the length of the wall. The distribution seal distributes stresses along the length of the wall and is specified as #4 bars at 12 I spacing. The concrete cover is 1.5 everywhere. Calculate the developmental length for the main reinforcement using the basic equation (ACI 318 -19: 25.4.2.4). Assume no transverse reinforcement Ktr-->0). Is the main reinforcement embedded deeply enough in the footing to fully develop its yield strength in tension?
Topic: Restrained Beams 140KN 2.5m 3.5m 5KN/m 3.2m МА 6m MB 11WL2 Pab² 5WL2 Pa?b MA = - MB = - 192 L2 192 L2 INSTRUCTION: 1. Determine the maximum stress in the timber beam with the size of 120 x 370mm.