A steel wide-flange beam has the dimensions as shown in the figure below. If it is subjected to shear force of V = 86 kN, plot the shear-stress distribution acting over the beam's cross section, with the magnitude of shear stress specified for the points of interest in the beam cross-section. 20 mm 110mm A 15 mm 110mm 20 mm 1y = 86 kN 310mm

A steel wide-flange beam has the dimensions as shown in the figure below. If it is subjected to shear force of V = 86 kN, plot the shear-stress distribution acting over the beam's cross section, with the magnitude of shear stress specified for the points of interest in the beam cross-section. 20 mm 110mm A 15 mm 110mm 20 mm 1y = 86 kN 310mm

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter5: Stresses In Beams (basic Topics)

Section: Chapter Questions

Problem 5.10.12P: The T-beam shown in the figure has cross-sectional dimensions: b = 210 mm, t = 16 mm, h = 300 mm,...

See similar textbooks

Similar questions

A U-shaped cross section of constant thickness is shown in the figure. Derive the following formula for the distance e from the center of the semicircle to the shear center. Also, plot a graph showing how the distance e (expressed as the non dimensional ratio e/r varies as a function of the ratio b/r. (Let b/r range from 0 to 2.)
Determine the shape factor f for a cross section in the shape of a double trapezoid having the dimensions shown in the figure. Also, check your result for the special cases of a rhombus (b1= 0) and a rectangle (b1= b2).
The Z-section of Example D-7 is subjected to M = 5 kN · m, as shown. Determine the orientation of the neutral axis and calculate the maximum tensile stress c1and maximum compressive stress ocin the beam. Use the following numerical data: height; = 200 mm, width ft = 90 mm, constant thickness a = 15 mm, and B = 19.2e. Use = 32.6 × 106 mm4 and I2= 2.4 × 10e mm4 from Example D-7
The T-beam shown in the figure has cross-sectional dimensions: b = 210 mm, t = 16 mm, h = 300 mm, and A, = 280 mm. The beam is subjected to a shear force V = 68 kN. Determine the maximum shear stress tntijlin the web of the beam.
Derive the following formula for the distance e from the centerline of the wall to the shear center S for the hat section of constant thickness shown in the figure: Also, check the formula for the special case of a channel section (a = 0).
A plastic-lined steel pipe has the cross-sectional shape shown in the figure. The steel pipe has an outer diameter d1= 100 mm and an inner diameter d2= 94 mm. The plastic liner has an inner diameter d1= 82 mm. The modulus of elasticity of the steel is 75 times the modulus of the plastic. Determine the allowable bending moment Mallowif the allowable stress in the steel is 35 M Pa and in the plastic is 600 kPa. If pipe and liner diameters remain unchanged, what new value of allowable stress for the steel pipe will result in the steel pipe and plastic liner reaching their allowable stress values under the same maximum moment (i.e., a balanced design)? What is the new maximum moment?
The cross section of a sign post of constant thickness is shown in the figure. Derive the formula for the distance e from the cent crime of the wall of the post to the shear center S: where I2. = moment of inertia about the z axis. Also, compare this formula with that given in Problem 6.9-11 for the special case of ß = 0 here and a = h/2 in both formulas.
Given the beam shown below, determine the shear force and bending moment at point C. Given the dimensions a = 2 m, b = 5.9 m and c = 2 m, and the load intensities e = 10 kN/m and f = 2 kN/m. e kN/m f kN/m am bm cm A B D Shear force (observe the up on the left, down on the right positive sign convention): SFc = Number Units (tolerance 0.2 kN) Bending moment (observe the sagging positive sign convention): BMc = Number Units (tolerance 1 kN*m)
The simply supported beam is subjected to the force F = 700 N and the uniform distributed load with intensity w = 150 N/m. Draw the shear force and bending moment diagrams (in your homework documentation) and determine the equations for V(r) and M(x). Take a = 0 at point A. 19 F a Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable Value a 5.2 m 2.6 m 3.12 m Support Reactions The reaction at A is N. The reaction at D is N. Shear Force and Bending Moment Equations In section AB: V(x)= N and M(x)= N-m. In section BC: v(x)- N and M(x)= N-m. In section CD: V(x)- N and M(x)= N-m. A
The T-beam shown in the figure has cross-sectional dimensions: b = 200 mm, t = 17 mm, h = 300 mm, and h₁ = 280 mm. The beam is subjected to a shear force V = 47 kN. A h₁ h с Determine the maximum shear stress max in the web of the beam. (Enter the magnitude in MPa. Assume that the shear force acts parallel to the y-axis and is uniformly distributed across the thickness of the web.) 4.0654 Your response differs from the correct answer by more than 10%. Double check your calculations. MPa
Beam cross section is shown in Figure Q3 and given the second moment of area is I= 20.85 x 106 mm*. If a resultant shear force, Vacting at the beam cross section is 40 kN, (a) Determine the shear stress at point M, N, O and P based on the given shear force. (b) Sketch the shear stress distribution over the cross section and label the shear stress values V= 40 kN M 80 mm 40 mm y =100 mm 80 mm 80 mm 30 mm 80 mm Figure Q3
The beam shown in the figure is made of Wood that has an Allowable Shear Stress of 200 psi; Determine the maximum value of Shear Force "V" that the section could withstand?, also draw the distribution of the shear stress over the section of the beam 12 in. 8 in.