A spherhe of aluminium is staying in an air atmosphere . Develop an equation of the tempeture distribution inside the sphere, with respect to the time. given: Ti- initial temperature of the aluminium ( homogeneous) Ta- air temperature (constant) k -conduction coefficient of aluminium hinf- convective coefficient air

A spherhe of aluminium is staying in an air atmosphere . Develop an equation of the tempeture distribution inside the sphere, with respect to the time. given: Ti- initial temperature of the aluminium ( homogeneous) Ta- air temperature (constant) k -conduction coefficient of aluminium hinf- convective coefficient air

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.51P

See similar textbooks

Similar questions

1.4 To measure thermal conductivity, two similar 1-cm-thick specimens are placed in the apparatus shown in the accompanying sketch. Electric current is supplied to the guard heater, and a wattmeter shows that the power dissipation is 10 W. Thermocouples attached to the warmer and to the cooler surfaces show temperatures of 322 and 300 K, respectively. Calculate the thermal conductivity of the material at the mean temperature in W/m K. Problem 1.4
1.15 A thermocouple (0.8-mm-diameter wire) used to measure the temperature of the quiescent gas in a furnace gives a reading of . It is known, however, that the rate of radiant heat flow per meter length from the hotter furnace walls to the thermocouple wire is 1.1 W/m and the convection heat transfer coefficient between the wire and the gas is K. With this information, estimate the true gas temperature. State your assumptions and indicate the equations used.
Determine the power requirement of a soldering iron in which the tip is maintained at 400C. The tip is a cylinder 3 mm in diameter and 10 mm long. The surrounding air temperature is 20C, and the average convection heat transfer coefficient over the tip is 20W/m2K. The tip is highly polished initially, giving it a very low emittance.
A section of a composite wall with the dimensions shown below has uniform temperatures of 200C and 50C over the left and right surfaces, respectively. If the thermal conductivities of the wall materials are: kA=70W/mK,kB=60W/mK, kC=40W/mK, and kD=20W/mK, determine the rate of heat transfer through this section of the wall and the temperatures at the interfaces.
A spherhe of aluminium is staying in an air atmosphere . what would be the change in the internal energy of the sphere with respect to the time given: Ti- initial temperature of the aluminium ( homogeneous) Ta- air temperature (constant) k -conduction coefficient of aluminium hinf- convective coefficient air Cp Cv
Don’t use Heissler charts to answer this question Heat sterilization of lumber, timbers, and pallets is used to kill insects to prevent their transfer between countries in international trade. This is analogous to food sterilization by heat. A typical requirement here is that the slowest heating point of any woodconfiguration be held at 56 °C for 30 minutes. Consider hot air heating of wooden boards that maintains their surface temperature at 70 °C. The boards are stacked outside and in the winter time they can be considered to be at 0 °Cwhen theyare brought in for heating. The thermal diffusivity of the wood is 9*10-8m2/s. a.Calculate the time from the start of heating for a 2.5 cm thick board to reach a sterilization temperature of 56 °C at its slowest heating point .b.Calculate the heating time when four such boards are stacked together. c.Calculate the ratio of the two heating times (for a single board versus when they are stacked), and explain the ratio. Note: You’re free to…
An underwater sonar that maps the ocean bathymetry is encapsulated in a sphere with a diameter of 85 mm. During operation, the sonar generates heat at a rate of 300W. What is the sonar surface temperature when it’s located in a water column where the temperature is 15o C and the water current is 1 m/sec? The sonar was pulled out of the water without turning it off, thus, it was still working. The air temperature was 15o C and the air speed was 3 m/sec. What was the sonar surface temperature? Was there any reason for concern?
Sepleniber 02 Heat is generated in a homogeneous spherical piece of radioactive material (2D - 8 cm) at rate of 71.8 MW/m and is dissipated to the environment. The center and surface temperatures of the spheres are (491°C and 80°C) respectively, What is the thermal conductivity of the radioactive material "W/m.K"?
For each of the following cases, determine an appropriate characteristic length Lc and the corresponding Biot Bi number that is associated with the transient thermal response of the solid object. Say if the global capacitance approximation is va lid. If temperature information is not provided, evaluate properties T = 300K a)oroidal shape with diameter D = 50mm and cross-sectional area AC = 5 mm², with thermal conductivity k = 2.3W / (mK) The surface of the toroid is exposed to a refrigerant corresponding to a convective coefficient eta = 50 W/( m2.k) b)A long stainless steel heated bar (AISI 304), with rectangular cross section, and dimensions w = 3mm , W = 5mm and L = 100mm . the bar issubjected to a refrigerant that provides a heat transfer coefficient of h =15 W/(m2 K) on all exposed surfaces. c)A long extruded aluminum tube (2024 Alloy) with internal dimensions and external w = 20 mm and W = 24 mm , respectively, suddenly submerged in water, with a convective coefficient of h =…
A brass plate has a circular hole whose diameter is slightly smaller than the diameter of an aluminum ball. Ifthe ball and the plate are always kept at the same temperature,(a) should the temperature of the system be increased or decreasedin order for the ball to fit through the hole? (b) Choose the bestexplanation from among the following:I. The aluminum ball changes its diameter more with temperature than the brass plate, and therefore the temperatureshould be decreased.II. Changing the temperature won’t change the fact that the ballis larger than the hole.III. Heating the brass plate makes its hole larger, and that willallow the ball to pass through.
There is a long cylinder inside an oven and we are using lumped capacitance method to find the temperature at its extremes. The temperature at the centre of the cylinder is 1000 C, what will be the temperature at its one end where it is away from heat source according to our calculations? not sufficient information more than 1000 C equal to 1000 C less than 1000 C
In a hot ball, Biot number and Fourier number are 0.2 and (10). Find the temperaturedistribution at center, temperature distribution at ball surface, and actual to maximum heattransfer ratio uses charts/table also if needed