A solid 30.0-mm-diameter steel [E = 290 GPa] shaft supports two pulleys as shown. Determine the shaft deflection at point C. Assume that the bearing at point A can be idealized as a pin support and the bearing at point E can be idealized as a roller support. ... B D C 300 mm 200 mm 300 mm 200 mm 750 N 500 N A -1.101 mm (B) -0.936 mm -0.876 mm D -1.586 mm E) -0.697 mm

A solid 30.0-mm-diameter steel [E = 290 GPa] shaft supports two pulleys as shown. Determine the shaft deflection at point C. Assume that the bearing at point A can be idealized as a pin support and the bearing at point E can be idealized as a roller support. ... B D C 300 mm 200 mm 300 mm 200 mm 750 N 500 N A -1.101 mm (B) -0.936 mm -0.876 mm D -1.586 mm E) -0.697 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q12 (Simple stress and strain) Item 3 of 3 A bar AB (A = 500 mm?) is hinged at A and is supported by a rod CD and C. The rod is pin connected at A, as shown. Neglect deflections of the bar due to bending. If the diameter of the rod connecting the load W = 90 kN is 20 mm, what is the displacement of the load? Use E=210 GPa. (10 38 mm. 2m 1.8m ww Diameter TYOR 2.5 m 1.5m 0.6m W=90kN
The thin plate ABCD of mass 8 kg is held in the position shown by the wire BH and two links AE and DF. Neglecting the mass of the links, determine immediately after wire BH has been cut (a) the acceleration of the plate, (b) the force in each link. H. E 150 mm 30% A B F 200 mm 30 D. IC 500 mm
H.W.: A horizontal rigid bar AB is hinged at A and subjected to 80 KN load and 120 kN.m moment at C as shown. Two vertical rods BE (of Steel) and DF (of Copper) try to assist the rigid bar AB to carry the load. Determine the stress in each of the vertical rods and the downward deflection at point C. Use Esteet = 200 GN/m², Ecopper = 120 GN/m². Copper F A-850 mm² L=1m 3m D 3 m A-600 mm² 120 kN.m L=1.5 m 80 kN * Steel E 2m
The bar AB is supported by two rods- steel on the left and bronze on the right. If the bar is horizontal before load P is applied, find the distance x (in meters) that locates the position where P must act if the bar is to remain horizontal. (E of steel 29000 ksi and E of bronze = 83 GPa) Neglect the weight of bar AB. L=2ft Aw02 in? A 0.4 in 1on
. Determine the magnitude of the moment of the 600-N force acting on the bracket shown. Expressyour un answer in Nm.
The rigid bar AD (figure STR-4) is supported by two steel wires of 1.5mm diameter (E = 200 GPa) and a pin and bracket at D. Knowing that the wires were initially taut. Determine the following: a. The additional tension in wire BE when a load P=900 N is applied at D. b. The additional stress in wire FC when a load P = 900 N is applied at D c. The corresponding deflection at point D.
3/98 Each of the three uniform 1200-mm bars has a mass of 20 kg. The bars are welded together into the configura- tion shown and suspended by three vertical wires. Bars AB and BC lie in the horizontal x-y plane, and the third bar lies in a plane parallel to the x-z plane. Compute the tension in each wire. B 600 mm 1200 mm A 30⁰! 1200 mm PROBLEM 3/98 600 mm -y
250 mm A D P = 25 kN B 30 60 C TOP VIEW 280 mm Member AD is fabricated by joining two bars (E=205GPA, G,A=82GPA) and is pinned to plate ABC using a 5 mm diameter pins as shown in the figure. The yield strength of the pins is T,=890MPA. Plate ABC is a right triangle and is fixed along its edge BC. A 25KN Force P is then applied at end D causing a lateral strain in member AD with magnitude equal to 7.5x104mm/mm. This also causes Point A to displace only along the horizontal resulting to a shear strain at point A equal to y,=+0.00165rad. Determine the following: 1. Poisson's ratio of material used in member AD, vD 2. The normal strain in member AD, CAD 3. The average stress experienced by pin A, TA 4. Factor of Safety of pin A with respect to yielding, FS,A 5. Displacement of point D, A,
8) If the elongation of wire BC is 0.2 mm after the force P is applied, determine the magnitude of force P. The wire BC is A36 steel and has a diameter of 3 mm. 200 G Pa E A36 400 mm 300 mm B 200 mm-
The solid 34-mm-diameter steel [E = 200 GPa] shaft supports two pulleys. For the loading shown, use discontinuity functions to compute: (a) the shaft deflection vg at pulley B. (b) the shaft deflection vc at pulley C. Assume LAB = 260 mm, LBC = 400 mm, P = 810 N, Q = 480 N. A LAB B LBC Q C
/stemezcom Lec3 working stres For the beam shown below, determine the concrete and steel stresses at the locations of the maximum positive and negative moments, Use ſ'c = 25Mpa. The answers are MPa, MPa, MPa and MPa. 3okN/m 8m 1m 4-25mmØ- -Top bars -4-16mmØ 250 250 bottom bars 630 630
250 mm A D P = 25 kN B 30 60 C TOP VIEW 280 mm Member AD is fabricated by joining two bars (E0=205GP,, Ga=82GPA) and is pinned to plate ABC using a 5 mm diameter pins as shown in the figure. The yield strength of the pins is T,=890MPA. Plate ABC is a right triangle and is fixed along its edge BC. A 25KN Force P is then applied at end D causing a lateral strain in member AD with magnitude equal to 7.5x10-mm/mm. This also causes Point A to displace only along the horizontal resulting to a shear strain at point A equal to y,=+0.00165rad. Determine the following: 1. Poisson's ratio of material used in member AD, vAD 2. The normal strain in member AD, caD 3. The average stress experienced by pin A, T, 4. Factor of Safety of pin A with respect to yielding, FS,A 5. Displacement of point D, A,