A single-phase full-bridge inverter fed by a 325 V DC produces a symmetric quasi-squarewaveform across 'ab' as shown. To achieve a modulation index of 0.8. the angle 0expressed in degrees should be.(Round off to 2 decimal places.)(Modulation index is defined as the ratio of the peak of the fundamental component ofVab to the applied DC value.)-325 VVab325 V0-325 V8/2112xE

A single-phase full-bridge inverter fed by a 325 V DC produces a symmetric quasi-square waveform across 'ab' as shown. To achieve a modulation index of 0.8. the angle 8 expressed in degrees should be (Round off to 2 decimal places.) (Modulation index is defined as the ratio of the peak of the fundamental component of Va to the applied DC value.) 325 V Hola 325 V 0 -325 V 8/2 A 2x 3

A single-phase full-bridge inverter fed by a 325 V DC produces a symmetric quasi-square waveform across 'ab' as shown. To achieve a modulation index of 0.8. the angle 8 expressed in degrees should be (Round off to 2 decimal places.) (Modulation index is defined as the ratio of the peak of the fundamental component of Va to the applied DC value.) 325 V Hola 325 V 0 -325 V 8/2 A 2x 3

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A single phase half a bridge bipolar PWM inverter is operated from a center top 240 volts DC supply. The fundamental output frequency is adjusted to 50 Hz, the carrier frequency used is 1.2 kHz, modulation index is adjusted to 0.8. Determine: i) Carrier ratio (Mf) and the number of pulses per cycle. ii) fundamental output voltage. iii) distortion and harmonic factor of the output voltage waveform. vi) Draw the waveforms created O a. 24 O b. 16 O c. 20 O d. 12
Q1- For single phase voltage source bridge inverter: 1- Draw the circuit. 2- With R=102 , L=50mH, frequency is 50 Hz , supply voltage is 450V and quasi-square wave output and a 50 percent on time, draw the waveforms of output voltage (VL.) and load current (iL) when I=25.05A , Io= -9.217A. 3- Calculate the RMS value of output voltage and mean output power.
A single phase half bridge inverter is operating from a 25 V DC source and supplies power to resistive load. What is the distortion factor of fundamental output voltage?
3. PWM Inverter The full bridge inverter is used to produce a 60 Hz voltage across a series R-L load using bipolar PWM. The dc input to the bridge is 100 V, the amplitude modulation ratio ma is 0.8 and the frequency modulation ratio m, is 21. The load has a resistance of R = 10n and a 20mH. Determine the a) the amplitude of the 60-Hz component of the output voltage and load current b) power absorbed by the load resistor c) THD of load series inductance of L current. m,=1 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 1.00 0.90 0.80 0.70 0.60 0.50 0.40 0.10 0.30 1.20 0.20 1.24 n=1 0.60 0.71 0.82 0.92 1.01 1.08 1.15 1.27 n=m, n=mf±2 0.32 0.27 0.22 0.17 0.13 0.09 0.06 0.03 0.02 0.00
Show that the THD of the phase voltage of the three-phase inverter square-wave mode is 0.31
The load voltage waveform of a single phase full bridge inverter supplied from 30OV DC voltage source is shown in below figure. Output frequency is 50HZ and the load consists of series R-L components. The load vahues are 22 and 0.04H, respectively. (Conduction interval for half period is 120°) 150 100 50 T -50 3 -100 -150 .002 .004 .006 008 .01 .012 .014 .016 .018 .02 Time (sec) a. Calculate and draw the load current for the first two-period interval b. Calculate and draw the load current for the steady-state condition c. Find the RMS values of the load voltage and the load current d Calculate and draw the voltage across the load inductance e. Calculate and draw the source current and find its average vahue
The load voltage waveform of a single phase full bridge inverter supplied from 300V DC voltage source is shown in below figure. Output frequency is 50HZ and the load consists of series R-L components. The load values are 22 and 0.04H, respectively. (Conduction interval for half period is 120°) 150 100 50 T -50 3 -100 -150 .002 .004 .006 .008 .01 .012 .014 .016 .018 .02 Time (sec) a. Calculate and draw the load current for the first two-period interval b. Calculate and draw the load current for the steady-state condition
Using the sine PWM method with the full bridge inverter below, it is desired to generate a voltage of 50Hz on the series RL load. A voltage of 120 V DC is applied to the input of the inverter circuit. Amplitude modulation rate ma = 0.9 and frequency modulation rate mj = 19. The resistance of the series RL load is 15 ohms and the coil inductance is 40 mH. What is the total harmonic distortion value (THD) of the power drawn by the load resistor and the load current?
The load voltage waveform of a single phase full bridge inverter supplied from 300V DC voltage source is shown in below figure. Output frequency is 50HZ and the load consists of series R-L components. The load values are 2N and 0.04H, respectively. (Conduction interval for half period is 120°) 150 100 50 T -50 3 -100 -150 .002 .004 .006 .008 .014 ,02 .01 Time (sec) .012 .016 .018 a. Find the RMS values of the load voltage and the load current b. Calculate and draw the voltage across the load inductance c. Calculate and draw the source current and find its average value
Homework 8 (1) A two-level VSC with the switching frequency 6kHz, the AC line frequency is 60Hz, find the two lowest frequency harmonics. (2)An MMC circuit with 201 units in each arms, find the levels for phase output voltage and line output voltage. (3)Make comparison of the properties of VSC and LCC as inverters.
For single phase voltage source bridge inverter: 1- Draw th circuit. 2- With R=102, L=50mH, frequency is 50 Hz and supply voltage is 400V and square wave output, draw the waveforms of vo and io. 3- Calculate the RMS value of output voltage and mean output power.
for square wave PWM inverter, Vdc=100V, L=25mH, R=1002, f=60Hz. draw the spectrum of the output voltage and current and then find the rms current value and the output power. Take n =1-20.