A reducing elbow deflects the water upwards at angle of 45 degree and discharge it to the atmosphere at mass flow rate of 30 kg/sec. The height of the exit from the reference level is 40 cm. The cross section area of the entrance and exit is 150 cm^2 and 25 cm^2, respectively. Calculate the magnitude of the FPx and FPy. Patm 25 cm? 45° Water 150 cm? 30 kg/s W-490 N MMM

A reducing elbow deflects the water upwards at angle of 45 degree and discharge it to the atmosphere at mass flow rate of 30 kg/sec. The height of the exit from the reference level is 40 cm. The cross section area of the entrance and exit is 150 cm^2 and 25 cm^2, respectively. Calculate the magnitude of the FPx and FPy. Patm 25 cm? 45° Water 150 cm? 30 kg/s W-490 N MMM

Solid Waste Engineering

3rd Edition

ISBN:9781305635203

Author:Worrell, William A.

Publisher:Worrell, William A.

Chapter5: Separation Processes

Section: Chapter Questions

Problem 5.32P

See similar textbooks

Similar questions

Quèstion 49 Avertical cylinder having a circular base of radius 'r and a height of 12 m is filled with water at the rate of 1 m-/min. If the depth of water in the cylinder at the vertical position is 3 m, what would be the resulting depth when the cylinder is in the horizontal position? O A.0.40r O B.0.60r OC.0.30r O D.0.50r « > A Moving to another question will save this response. acer F12 PrtSc Pause Del Home Pg Up F7 F8 F9 F10 F11 F3 F4 F5 F6 Scr Lk SysRq Break Ins * % Backspace 4 5 € 6 7 8 9. W E Y U P F G K
5. Find the Total efongation of the bar below 12kN OKN 4KN 4KN+ 6KN LI 1.2 L3 L4
Question: Cd= 1:0 = 0=1cm @ Derive The Equation Of Motion In Terms Of Height 2 Time For... Cd-1:0 D=I cm DeriDe the caationo Motirn in terms o height Tme Sor empgtng the tank Pen 1om 5m
How long will it take to sink an open and empty vessel 4 m x 4 m x 2m high, with a draft of 1.6 m, when 85 mm Ф dia, hole at it bottom is opened C= 0.75. A. 135sec B. 268sec C. 311 sec D. 220sec
1. Please show your understanding of 4R in equation (4.6) by assuming it is a full pipe flow with a pipe diameter d. To fpV /8 f v? (4.6) %3D %3D %3D L. yR YR 4R 2g
Approximateły what pressure must be applied to water at 60 deg Fahrenheit (Compressibility is equal to 3 22x10-6 in 2/lb) ta reduce its volume 25 percent? Select the correct response(5)* 7763 98 psi 7367.98 psi 7676.98 psi 7673.98 psi
A 250 mm x 125 mm venturimeter is provided in a vertical pipe line carrying oil of specific gravity of 0.9, the flow being upwards. The difference in elevation of the throat section and entrance section of the venturimeter is 0.5 m. The differential U-tube mercury manometer shows a gauge deflection of 300 mm. Coefficient of venturimeter is 0.96 and specific gravity of mercury is 13.6 Calculate the following: a) Discharge of oil b) The pressure difference between the entrance section and the throat section..
Can Please Help Me: Civil Engineering 60 minutes only the given time. Wish you could help me. I will give UPVOTE and GOOD FEEDBACK. //Question A 2 foot diameter pipe carries stormwater discharge from a site. The concrete pipe was designed with a slope of 0.8 foot per 100 feet. At the time of measurement, the pipe has 0.8 feet of discharge flowing in it. If the roughness coefficient of the concrete pipe is 0.013, what is the streamflow discharge in gallons per minute? [Ans. 3,084gpm] //Question
Problem 4. (15pts) An unknow fluid has a specific gravity of 1.25 and viscosity of 5x10-³Ns/m². Determine the kinematic viscosity in [m²/s]. Track units.
Question 1: Determine the flows in the netw ork shown in Fig Q1, neglecting minor losses. Data: Pipe АВ BC BD ВЕ EF EG Length (m) 10 000 3 000 4 000 6 000 3 000 3 000 Diameter (mm) 450 250 250 350 250 200 Roughness of all pipes, Ks = 0.03 mm - 150 A 100 80 - 75 Figure Q1 60 G
Water flows through a 28 cm (length) rotameter (Type A) with an internal diameter of 25 mm at the top and 20 mm at the bottom. The float has a diameter of 20 mm, a volume of 6.1 cm and a specific gravity of 5.3. 15. Assuming that Az/A, is negligible, what is the area (in mm² to 5 significant figures) of the annulus when there is a flow of 380 I/hr water? Assume Co = 0.97 16. Using the same constant Cp value, recalculate the area of the annulus assuming Az/A, is not negligible (in mm? to at least 5 significant figures). 17. What is the final value of the linear flowrate through the annulus? (m/s) 18. What is the final Reynolds number through the annulus? 19. How far from the bottom is the float under these conditions? (cm) Answer the following questions as true or false: 20. A rotameter is typically placed vertically while an orifice meter is placed horizontally 21. An orifice meter requires only a change in pressure of the pipe to calculate the flowrate 22. An orifice meter is an…
issues from the tank in shown at Q = 45 f3/h. Assume laminar flow conditions and neglect entrance and exit losses. (a) What is the velocity of flow in the pipe. Ans: 9.167 ft/s (b) Determine the head lost in the pipe. Ans: 7.695 feet - Determine the kinematic viscosity of the paint in ft?/s. Ans:0.0002444