A low-pass channel with a maximum frequency of fr Hz is to be used in system. Assume that the wave length for fn is 100 meters and the signal (SNR) is 127 dB. (Assume speed of light to be 3x10° m/sec) a. The bandwidth of the channel is Hz b. The theoretical highest data rate for the channel is bps. c. based on the data rate in part (b), the minimum number of signal leve to represent data will be levels

A low-pass channel with a maximum frequency of fr Hz is to be used in system. Assume that the wave length for fn is 100 meters and the signal (SNR) is 127 dB. (Assume speed of light to be 3x10° m/sec) a. The bandwidth of the channel is Hz b. The theoretical highest data rate for the channel is bps. c. based on the data rate in part (b), the minimum number of signal leve to represent data will be levels

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A carrier signal is amplitude modulated by a sinewave. The resulting AM waveform is shown below. 3.5V- 1V- a) What is the amplitude of the carrier signal? b) c) To achieve 75 percent modulation, what amplitude of the modulating signal is needed? d) Calculate the effective voltage of the AM signal What is the modulation index?
IX. A carrier signal is amplitude modulated by a sinewave. The resulting AM waveform is shown below. a) b) c) d) 5.5V- 2V What is the percentage of modulation? What is the amplitude of the carrier signal? To achieve 75 percent modulation, what amplitude of the modulating signal is needed? Calculate the effective voltage of the AM signal
6.a. Which of the following can you accurately measure using an OSA?A. Signal power in a channel onlyB. Spectral width of a channel onlyC. Center wavelength of a signal onlyD. Signal power and spectral width of a channel and center wavelength of a signal6.b. Which instrument should you use to determine the receiver sensitivity threshold during a receiver sensitivity test?A. BER testerB. OTDRC. Reel testerD. Variable optical attenuator
1 Can we generate FM signal using PM modulator? * Yes No
A channel having a bandwidth of 1 kHz, the power of signal is 10 W and the power of noise is 5 W. Determine the channel capacity. Or: A channel having a bandwidth of 1 kHz and Signal to Noise Ratio (SNR) is 2. Determine the channel capacity.
1) We need transmission effiency (n) 2) Minimum and Maximum frequency values of the FM signal. ( kHz)
Please explain the waveforms, what are the reason why does the 3rd waveform (Recovered signal) is attenuated. 1st waveform: Carrier signal (2Vpk,20 kHz) 2nd waveform: Information signal (1Vpk,1kHz) 3rd waveform: Recovered signal
i)Modulation process takes place in the modulator with two injection signals namely data orinformation and carrier. It is a vital step in generating a decent signal for electronic communication.Whenever the carrier is modulated by the information signal, new signals at different frequenciesare generated as part of the process. These new frequencies occur in the frequency spectrum withinthe range of the carrier frequency. Conclude these frequencies and mathematically explain itsgeneration with the help of diagrams. A) Upper sideband and lower broadbandB) Lower sidefloor and upperside floorC) Lower peak and upper peakD) Upper sideband and lower sidebandE) Lower bandwidth and upper gainF) All of the aboveG) None of the above
then second questrion po eh eto 2. Determine the over-all transmittance of the signal flow graph shown below.
FM Demodulator Circuit Design I need an FM demodulator circuit for Frequency Modulated Sound Signal with 127MHz carrier frequency. I need clear mathematical steps for element value calculations. Thanks in advance.
For an AM DSBFC modulator with a carrier frequency f. = 100 kHz and a maximum modu- lating signal fm(max) = 5 kHz, determine a. Frequency limits for the upper and lower sidebands. b. Bandwidth. c. Upper and lower side frequencies produced when the modulating signal is a single- frequency 3-kHz tone. Then d. Sketch the output frequency spectrum.
Multiple Choice directions: Circle the letter of the answers that best answer the question. 29. In a klystron amplifier, velocity modulation is produced by:a. Buncher cavityb. Cathodec. Catcher cavityd. Collector30. At what position is the input signal inserted into a traveling wave tube?a. At the collector end of the helix b. At the collector c. At the control grid d. At the cathode end of the helix31. The main frequency determining element of a klystron is:a. Its mode of operation b. The accelerating voltagec. Its resonant cavityd. The repeller voltage Note: Explanation is not needed just provide the correct answers for each number.