A 50-ohm source has an RMS open-circuit output voltage of 1 volt at 100 MHz a. What peak voltage will appear across a 50-ohm load connected to this source b. Express this voltage in dBm. (Hint: careful of peak/rms voltage.) c. If the source is connected to the 50-ohm load through a lossless 50-ohm cable, what will the peak voltage at the load be? d. e. If the source is connected through a 50-ohm load through a 100-ft lossy 50-ohm cable, and the loss is 0.5 dB/10 ft, what will be the peak voltage at the load? Say that the "peak" (not RMS) voltage in part a. was 1 volt (i.e. the sinusoidal signal ranged from -1 to +1 volts). What would be the reading across a 50-ohm load in this case, if measured by a spectrum analyzer? Note that a spectrum analyzer produces a reading in dBm, not volts. Assume are no cables in this case.

A 50-ohm source has an RMS open-circuit output voltage of 1 volt at 100 MHz a. What peak voltage will appear across a 50-ohm load connected to this source b. Express this voltage in dBm. (Hint: careful of peak/rms voltage.) c. If the source is connected to the 50-ohm load through a lossless 50-ohm cable, what will the peak voltage at the load be? d. e. If the source is connected through a 50-ohm load through a 100-ft lossy 50-ohm cable, and the loss is 0.5 dB/10 ft, what will be the peak voltage at the load? Say that the "peak" (not RMS) voltage in part a. was 1 volt (i.e. the sinusoidal signal ranged from -1 to +1 volts). What would be the reading across a 50-ohm load in this case, if measured by a spectrum analyzer? Note that a spectrum analyzer produces a reading in dBm, not volts. Assume are no cables in this case.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

a carrier frequency 10⁶ and amplitude 3V frequency modulated by a sinusoidal wave of frequency is 500 HZ and the peak amplitude 1 Volt as a consequence , the frequency deviation is 1 KHz. The level of the modulating waveform is changed to 5 Volt peak and the modulating frequency is changed to 2KHz. Write an expression for the new modulated waveform.
Example 6 The EMF and current waves of a circuit having resistance only are e=170sin27 60t and i=14.14sin 27 60t. Determine. a.) Equation of power wave b.) Frequency of power wave c.) Maximum value of power wave Average power d.) e.) Power when t=1/480 sec, 1/240 sec, 1/90 sec. f.) Draw voltage, current and power waves.
For a series ac circuit having resistive and reactive components, What does volt-ampere (VA) mean?, What does volt-ampere-reactive (VAR) mean?, How is VAR calculated?
4. A CT with an excitation curve given in the figure has a rated current ratio of 500:5 A and a secondary leakage impedance of 0.1 +j0.5 ohms. Calculate the CT secondary output current and the CT error for the following cases: a.) The impedance of the terminating device is 4.9 +j 0.5 ohms and the primary CT load current is 400 A. b.) The impedance of the terminating device is 4.9 +j0.5 ohms and the primary CT load current is 1200A c.) The impedance of the terminating device is 14.9 + j 1.5 ohms and the primary CT fault current is 400 A. d.) The impedance of the terminating device is 14.9 + j 1.5 ohms and the primary CT fault current is 1200 A w 100 80 60 40 20 2 4 6 10 Secondary exciting amps-, Secondary exciting volts-E'
Q1: Determine the average power and energy of the CT signal shown in Figure (1), then classify th as power or energy signal. x(+) 1 *w. -2 Figure (1) ...
In a series eaperiment with R, =1n and R, 4n across a power Supply E, the slope g (E, v, ) and of CE,V2) are re spechively (...) C ---- ) (a) 2 , 3 ( b) 5 , 1.25 (e) 2.15 , 5 (d) 3, 2
What type of RCCB's we must use in AC Circuits? Can we use RCCB in DC circuits? Why?
1) how did the soution for the collector current become VCC/(Re+Rc)? please explain 2.)instead of using the boxed solution, would it be alright to use KVL instead to solve for the collector current? If yes, please show the equation for the KVL.
. Draw and explain the structural overview of MOSFET Capacitances.
We measure and record the instantaneous voltage between the two wires of a power transmission line at arbitrary locations. The measurements at two locations: 0.3m apart. Will the two waveforms be different? If it is different, describe the difference. If so, by how much (negligible to significant).
2. What is the maximum efficiency value for an AM system that has a modulating signal a sinusoidal sign?
Draw a timing diagram for the circuit in Figure 2.24a. Show the waveforms that can be observed on all wires in the circuit. X2 f X3 X1 (a) A minimal sum-of-products realization Repeat Problem 2.8 for the circuit in Figure 2.24b. X1 X3 X2 (b) A minimal product-of-sums realization