A 13-kN hydraulic press for removing and reinstalling bearings in small-to medium-sized electric motors is to consist a commercially available cylinder mounted vertically in a C- frame, with dimensions as sketched in the Figure shown below. It is being proposed to use ASTM A-48 (Class 50) gray cast iron (brittle material with ultimate strength, S 345 MPa) for the C-frame material. Calculate the bending moment about the centroidal axis upto 3 digits after decimal point in KN.m? 18 mm 38 mm 13 kN 25 mm 10 mm -90 mm A 10 mm

A 13-kN hydraulic press for removing and reinstalling bearings in small-to medium-sized electric motors is to consist a commercially available cylinder mounted vertically in a C- frame, with dimensions as sketched in the Figure shown below. It is being proposed to use ASTM A-48 (Class 50) gray cast iron (brittle material with ultimate strength, S 345 MPa) for the C-frame material. Calculate the bending moment about the centroidal axis upto 3 digits after decimal point in KN.m? 18 mm 38 mm 13 kN 25 mm 10 mm -90 mm A 10 mm

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.3.5P: Solve Problem 11.3-3 for a W 10 × 45 steel column having a length L = 28 ft.

See similar textbooks

Similar questions

Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.
Solve Problem 11.3-3 for a W 10 × 45 steel column having a length L = 28 ft.
QUESTION 4 A 13-kN hydraulic press for removing and reinstalling bearings in small-to medium-sized electric motors is to consist of a commercially available cylinder mounted vertically in a C- frame, with dimensions as sketched in the Figure shown below. It is being proposed to use ASTM A-48 (Class 50) gray cast iron (brittle material with ultimate strength, S 345 MPa) for the C-frame material. Calculate the location of neutral axis upto 2 digits after decimal point in mm? 18 mm 38 mm 13 kN 25 mm 10 mm 90 mm At +A 10 mm 10.86 QUESTION 5 A 13-kN hydraulic press for removing and reinstalling bearings in small-to medium-sized electric motors is to consist of a commercially available cylinder mounted vertically in a C- frame, with dimensions as sketched in the Figure shown helow It ic heing pronosed to mse ASTM A-48 (Clace 50) ara cast iron (hrittle material with ultimate strength Click Save and Submit to save and submit. Click Save All Answers to save all answers. Save All An arch
Calculate the reaction forces on the bearing near the pulley and bearing at the far end of the shaft. Include a free body diagram and coordinates. Given the shaft length is 1 meter= Mass=40Kg Static load = 8600N Dynamic (running load) = 8400N Some hints:1. This solution will require you to draw known forces and find unknown reactions in 2perpendicular planes and then add the horizontal and vertical reaction forces asvectors to find the reaction force (hypotenuse).2. Bearings are usually mounted as near as possible to the ends of the shaft withoutfouling the other machine elements. The bearing at the far shaft end can be mountedat the 1 meter point. The bearing at the pulley end should allow clearance to assemblethe pulley.3. Bearing reaction forces are typically simplified as a single point load through thebearing centre.
Design a scissor jack for a typical vehicle.• Specify design considerations/requirements (weight to be lifted, initial position, final position, safety factor,etc.)• Specify dimensions and select material for all members. Use the same design channel (Ex. U-channel) forthe 4 major members. Consider buckling if the member is under compression. Specify thread dimension(including engagement length) for the center/horizontal member
Design a typical rigid flange coupling for connecting a motor and a centrifugal pump shafts. The coupling needs to transmit 15 KW at 1000 rpm. The allowable shear stresses of the shaft, key and bolt materials are 60 MPa, 50 MPa and 25 MPa respectively. The shear modulus of the shaft material may be taken as 84GPa. The angle of twist of the shaft should be limited to 1 degree in 20 times the shaft diameter. Note: show complete solution
Design a typical rigid flange coupling for connecting a motor and a centrifugal pump shafts. The coupling needs to transmit 15 KW at 1000 rpm. The allowable shear stresses of the shaft, key and bolt materials are 60 MPa, 50 MPa and 25 MPa respectively. The shear modulus of the shaft material may be taken as 84GPa. The angle of twist of the shaft should be limited to 1 degree in 20 times the shaft diameter. Note: show complete handwritten solution
Problem 1. Select a proper key for the joint shown in figure bellow. Shaft has a diameter of 30 mm and transfers a constant torque of T= 180 N.m. The hub has length of Ia=50mm. The key is made from steel with Oall comp 3D 120 МPа оall sh 3D 100 MPа. %3| Table 2.1 Square key parameters Keyslot depth Keyway depth t1 1,8 2,5 3,0 3,5 3,5 3,5 4,0 5,0 Shaft diameter Key parameters 3 1,4 12 - 17 17 - 22 22 - 30 30 - 38 38 - 44 44 - 50 50 - 58 58 - 65 4 1,8 2,3 2,8 2,8 2,8 3,3 3,3 5 10 6 12 14 6 16 7 18 7 Lp Figure 1. Square key parameters. All dimensions are in millimeters.
Your task is to design a full journal bearing to support the crankshaft of an engine. The crankshaft would be attached a journal that would be rotating within the bushing. The maximum speed of rotation of the crankshaft is 6000 rpm. The operating temperature is 130-F. The load on the bearing is 675lbf. The journal diameter has to fit on the crankshaft and has to be 2.5in. The length of the bearing has to be under 1.5in. The oil used in the engine is SAE 50. The performance of your bearing should have a maximum coefficient of friction of 0.04 and a minimum film thickness no lower than 0.001in. Determine the bearing dimensions you will use based on your goals and the charts in your formula sheet.
Shown below is a figure of a landing gear configuration on the VS and VD planes (for landing gear the directions V, D, and S are often used instead of x, y and z) This gear unit is assumed to represent one side of the main gear on a tricycle type of the landing gear system. The loading assumed corresponds to a condition of nose wheel up or tail down. The design load on the wheel is vertical and it s magnitude for this problem is 15,000 lbf. Determine the reactions at F, H, and G. The fittings at F and H are pinned and therefore cannot transmit any bending moments. The fitting at G is also a pinned fitting.
1. A component in an aircraft flap actuator, shown in Figure 1, can be adequately modelled as a cylindrical bar subjected to a compressive axial force of 8 kN, a bending moment of 55 Nm and a torque of 30 Nm. It is to be manufactured of a 20 mm diameter solid bar of 7075-T6 aluminium alloy. FLAP ACTUATOR (a) (b) (c) (d) (e) POWER SCHEW JACK CARRIAGE -FAPERON BALL NUT FLAP NOSE ROLLER BEAM FITTING CARRIAGE ROLLER -COLLAPSIBLE DOOK Figure 1: Aircraft Flap Actuator At a critical point on the bar surface, determine the value of the, (1) compressive direct stress, (ii) (iii) tensile bending stress, and shear stress. Indicate on a representative element in 2-D cartesian coordinates the stresses calculated in (a). Determine the principal stresses and the maximum shear stress at the point. Sketch the Mohr's stress circle representing the stress system and clearly mark on it the principal stress values calculated in (c) above and the direction (angle) of the maximum principal stress (0₁) with…
PCS Problem 105: Bearing Stress Explain briefly the purpose of the bearing plate between the steel column and the concrete pedestal.