A 1 m rigid tank contains steam at 200°C. 15% of the volume is in the liquid phase and the rest is in the vapor form. Steam 1 m3 200 °C Determine: 1) What is the state of the steam ? and why ? 2) The pressure of the steam ? 3) The mass and volume of the liquid phase? 4) The mass of volume of the vapor phase? 5) The quality of the saturated mixture ? 6) The density of the mixture?

A 1 m rigid tank contains steam at 200°C. 15% of the volume is in the liquid phase and the rest is in the vapor form. Steam 1 m3 200 °C Determine: 1) What is the state of the steam ? and why ? 2) The pressure of the steam ? 3) The mass and volume of the liquid phase? 4) The mass of volume of the vapor phase? 5) The quality of the saturated mixture ? 6) The density of the mixture?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

10 Ibm/min of Steam at 4.5 MPa with a moisture content of 7% undergoes a constant volume process until the pressure becomes 10.3 MPa. Determine the following: Pv and ts diagram .Specific volume, m³/kg Temperature at point 1 and 2, °C Au in kJ/kg, Ah in kJ/kg, and As in kJ/kg-K Heat Transferred in kW
1.8 m3 rigid tank contains steam at 220 oC. One-third of the volume is in the liquid phase and the rest is in the vapor form. Determine (a) the pressure of the steam, (b) the quality of the saturated mixture, and (c) the density of the mixture.
Determine the mass, in kg, of a a 1m3 tank containing argon gas at 600 kPa and 400 K. Report your answer to two decimal places using rounding.
(b) A frictionless piston-cylinder device as shown in Fig. Qlb contains water at 400 kPa and the water is heated at constant pressure from saturated liquid to saturated vapor. Then, the heating process is continued in an isobaric manner until its specific volume reaches the value of 0.5 m²/kg. Water Heat Figure Q1b i) What is the initial temperature of water in the cylinder? ii) What is the final temperature of water in the cylinder? iii) Calculate the total boundary work during the processes, kJ/kg. iv) Calculate the total amount of heat transferred during the processes, kJ/kg. v) Sketch both processes on a T – v diagram with respect to saturation lines.
A substance is contained in a piston cylinder assembly with properties as described by the attached saturation and superheated vapor tables. The piston has a mass of 50kg and face area of 49.5 square-centimeters. The assembly contains 5kg of a mystery substance and is stored outside. Overnight the temperature drops to 10°C, but the temperature rises during the afternoon. Mechanical stops prevent the piston from leaving the cylinder. Take the substance to be the system.
Given 280 liters of a gas at a 63.5 cm Hg. The gas has a specific heat at constant pressure of 0.847 kJ/kg K and a specific heat at constant volume of 0.659 kJ/kg K. Which of the following most nearly equals the volume of the gas would occupy at a final pressure of 5atm if the process is adiabatic?
Saturated water vapor at (T1,P1) is condensed to a saturated liquid at (T2,P2) in a spring-loaded piston-cylinder device, where (T1> T2), the expression for heat transfer for this process, in kJ/kg, will be Select one: A. Q = (u2 -u1)+0.5*(P2+P1)*(v2-v1) B. Q = (h2 -h1)+0.5*(P2+P1)*(v2-v1) C. Q = (h2 -h1)-0.5*(P2+P1)*(v2-v1) D. Q = h2 -h1 E. Q = (u2 -u1)-0.5*(P2+P1)*(v2-v1) F. Q = u2 -u1 G. Q = (h2 -h1)+(P2+P1)*(v2-v1) H. Q = (u2 -u1)+(P2+P1)*(v2-v1)
A rigid tank contains 2 kg of water at 100 C and 60 percent quality. In the question that follows, select the answer that is closest to the true value. What is the volume of the rigid tank in units of m3?
A piston/cylinder arrangement contains 2 kg of ammonia at a temperature 132.45 ℃ and a pressure 5 MPa. The piston floats. Heat is added to the system until the temperature of ammonia reaches 416.37 ℃. (a) Determine the phase of ammonia during the whole process (from the initial to the final state). (b) Show the initial and final points of the process in a T-s and p-v diagram. In both diagrams sketch the dome. Show these two points relative to the dome. (c) Determine the initial and final volume of the piston/cylinder arrangement using tables.
A piston/cylinder arrangement contains 2 kg of ammonia at a temperature 132.45 ℃ and a pressure 5 MPa. The piston floats. Heat is added to the system until the temperature of ammonia reaches 416.37 ℃. (a) Determine the phase of ammonia during the whole process (from the initial to the final state). (b) Show the initial and final points of the process in a T-s and p-v diagram. In both diagrams sketch the dome. Show these two points relative to the dome.
In an exothermic process, the volume of a system expanded from 213 mL to 2135 mL against a constant pressure of 752 torr. During the process, 29.1 calories of heat energy were given off. What was the internal energy change for the system in joules?
A 1.5m3 tank containing one kilogram of an unknown ideal gas is pressurized at 600 kPaa. What is the unknown gas in the tank if the inside temperature is 160oC?