57. An RLC series circuit connected to a 110-volt and 50-cycle AC source, contains the following series resistances and reactances: R1=10 ohm, R2= 15, XL1=20 ohms, XL2=25 ohms, XC= 40 ohms. Find the following a. Total inductance in millihenry b. total current c. reactive power

57. An RLC series circuit connected to a 110-volt and 50-cycle AC source, contains the following series resistances and reactances: R1=10 ohm, R2= 15, XL1=20 ohms, XL2=25 ohms, XC= 40 ohms. Find the following a. Total inductance in millihenry b. total current c. reactive power

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter21: Resistive-capacitive Series Circuits

Section: Chapter Questions

Problem 7RQ: An RC series circuit is connected to a 120-V, 60-Hz power source. The resistor is 25 and has a...

See similar textbooks

Related questions

Q: Q2. A coil of resistance 102 is connected in series with inductance 100mH is connected to a 215V, 50…

A: Inductance-Inductor twists in a number of turns are called inductors or coil. Inductance does not…

Q: A series circuit composed of a resistance of 24 ohms, an inductance of 0.09 henry and a capacitance…

Q: 3. A 3-phase, 50 Hz, 3000 V motor develops 600 H.P. (447-6 kW), the power factor being 0-75 lagging…

A: Given power factor 1 = 0.75 lagging raised power factor = 0.95 lagging

Q: Given the following Resistances and Inductors in Series and Voltage Source: R1 = 1,251 ohms R2 =…

Q: An impedance coil, in series with a resistor takes a current of 5 A when binected to a 100-V AC…

Q: Voltage

Q: 18/1.A. Draw the phasor diagram, also write the voltage and current relation statements for the…

A: Since it is an ac circuit the voltage and current will have phase angle between them. We will…

Q: 1-Choose the correct statement for pure resistor connected across single phase AC supply. a.…

A: Resistance Voltage and current are in same phase I=V/R So both are in same phase.

Q: An RL series circuit is connected to a 60-Hz, 208-volt power line. A clamp-on ammeter indicates a…

A: Disclaimer: Since you have asked multipart questions, we will solve the first three subpart for…

Q: Q4: A single-phase AC voltage controller is used to control the power flow from 110 V, 60 Hz source…

Q: A generating voltmeter is required to measure voltage between 15kV and 250kV. If the indicating…

A: Given that:Measure voltage between: 15KV to 250 KV Imn=2μA Imax=35μA Speed of…

Q: A series resistance – capacitance (R – C) circuit is connected to 230 – volt, 50 cycle AC source.…

Q: Example Question 1 A dynamometer-type AC ammeter made of moving coils and fixed coils with a shunt…

A: For a dynamometer-type AC ammeter -The moving coil's resistance is,R=10ΩThe shunt resistance…

Q: 3. A coil consists of a Resistance of 980and an inductance of 180 mH. if an alternating voltage…

A: Given data, Resistance R=98 Ω Inductance L=180 mH = 0.18 H Voltage equation V=180sin480t V

Q: 2. Discuss the difference between impedance, admittance and susceptance

A: In this question we will find difference between impedance admittance susceptance...

Q: A series resistance-capacitance (R-C) circuit is connected to a 230 volt 60 cycle source. If the…

Q: resistance of 18 ohms and an inductance of 0.122 henry is connected in series with a capacitor to a…

A: In an RLC series circuit the impedance is the combination of resistance, inductive reactance and…

Q: 11. A utility company plans to connect a total of 20 µ.F of capacitance to a 7200-V line. To make…

A: Whenever we connect the capacitors in series the then equivalent capacitance will decrease Let us…

Q: A coil is connected to a 230 volt source. If the voltage across the inductor is 125v, and the power…

A: The solution is given below

Q: The series constants R and L of a coil are to be determined by connecting the coil in series with a…

Q: A Coil of Resistance RQ and Inductance L in mH in series with a C in µF Capacitor, is connected to a…

A: "Since you have posted a question with multiple sub parts we will solve first three subpart for you…

Q: Given the following Resistances and Inductors in Series and Voltage Source: R1 = 1,664 ohms %3D R2 =…

A: In the given series circuit R1= 1664 ohms R2= 1999 ohms Total R = R1+R2 R =3663 ohms…

Q: A resistor R and an impedance coil Z are connected in series. The combination is supplied by a…

A: As per our company guidelines we are supposed to answer only first 3 subpart kindly repost the other…

Q: find its resistance, reactance and inductance.

Q: resistor R and an impedance coil Z are connected in series. The combination is supplied by a…

Q: Three identical coils, each of resistor 2ohm and inductive reactance 6.28 ohm are connected in delta…

A: Given, R=2 ΩXL=6.28 ΩVL=100 Vf=100 Hz Delta connected.

Q: An alternating current, i = 1.414 Sin (2 π x 50 x t) A, is passed through a series circuit…

Q: An inductance of 0.106 Henry is connected to a 120-volt 60-cycle source. Calculate (a) the inductive…

A: As per our guidelines we are supposed to be answer only the first 3 questions. Kindly repost the…

Q: Exercise 2: Resistance-Capacitance Series Circuits on an AC Supply Calculate (a) peak to peak…

A: Resistance-Capacitance Series Circuits on an AC Supply Calculate (a) peak to peak voltage (b) time…

Q: plase answer five a quesion option corrctly 9.In AC circuits, power consumed is A.it depends…

A: In this question we will find power in ac circuits , potential transformer etc.. As per our…

Q: A single-phase ac voltage source has 200 Vrms and a system connected consumes an active power of 300…

A: Given data, Active power P = 300 W RMS voltage V = 200 V RMS current I = 2.5 A

Q: 1. An inductor has an inductance of 0.65 henry and is connected to a 277 volt, 60 Hz line. How much…

Q: Given a variable resistor R of unknown resistance connected in parallel with an inductive reactance…

A: The solution is given below

Q: Pcoil -| mW At 60 Hz frequency, switch the SW to other pole to terminate the Rin the circuit.…

Q: 53. A series resistance-capacitance (R-C) circuit is connected to 230-volt, 50 cycle AC source. The…

Q: 28. Assume an inductor is connected to a 180-V AC line and the inductor has an induced voltage of…

Q: motor with 1mH of inductance and an unknown internal resistance is connected to a 100V RMS 10kHz…

Q: single-phase AC

A: Solution of this question deals with concepts of 1phase AC motor & concept of power factor,…

Q: (A) The capacitances of a 3-phase belted cable are 12-6 µF between the three cores bunched together…

A: Consider the given below diagram of the cable,

Q: 3. For a parallel circuit of 20 ohms resistor and a 10 ohms inductor, is connected to a 110/60 cps…

A: We need to find out current for given circuit

Q: For the series RL circuit shown in the figure below, answer the following questions and justify your…

A: 1) The inductance of the inductor will beL=μN2×Cross section areaLengthSince all the parameter of…

Q: 3. A coil consists of a Resistance of 980and an inductance of 180 mH. if an alternating voltage v-…

Q: Three identical coils, each of resistor 2ohm and inductive reactance 6.28 ohm are connected in delta…

A: In delta connection Phase voltage is equal to line voltage and line current is 3 times of phase…

Q: 2. A resistor of 6 0 and an unknown impedance coil in series draw 12 amps from a 120 volts, 60 Hz…

Q: Consider an RL circuit connected to a 230 v, 50 Hz supply with a power rating of 500 VA. What is the…

A: We need to find a Inductive reactance and Inductance of the given circuit.

Q: Q2. A coil of resistance 5Ω is connected in series with inductance 120mH is connected to a 215V, 50…

A: Consider the circuit,

Q: A resistor R and an impedance coil Z are connected in series. The combination is supplied by a…

A: We need to find out power factor, current, impedance for given circuit

Q: A 3-0, 50-Hz, star-connected, 2,000 kVA, 2,300-V alternator gives a short-circuit current of 600 A…

Q: 6. A resistance of 50-2 is connected in series with a capacitance of 20 µF. If a supply of 200 V,…

A: To solve above problem, one should have basic idea about working of AC circuits. Above given circuit…

Q: Consider an RL circuit connected to a 230 V, 50 Hz supply with a power rating of 500 VA. What is the…

A: In this question we need to find a Inductive reactance and Inductance value.

Question

57. An RLC series circuit connected to a 110-volt and 50-cycle AC source, contains the following series
resistances and reactances: R1=10 ohm, R2= 15, XL1=20 ohms, XL2=25 ohms, XC= 40 ohms. Find the
following
a. Total inductance in millihenry
b. total current
c. reactive power

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Alternating Current (AC) Series Motor and Universal Motor

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating of 600 WVDC. The capacitor and resistor are connected to a 480-V, 60-Hz circuit. Is the voltage rating of the capacitor sufficient for this connection?
An RC series circuit is connected to a 120-V, 60-Hz power source. The resistor is 25 and has a voltage drop of 65 volts. What is the capacitance of the capacitor?
A resistor R and a capacitor C are connected in series across a 400 V variable ac supply. When the frequency is 40 Hz, it draws 10 A current, and when the frequency is 50 Hz, it draws 15 A current. Find R and C.
A utility company plans to connect a total of 20uF of capacitance to a 7200 volt line. To make this connection four capacitors will be connected in series. What is the capacitance of each capacitor? Answer is 80uF. Now what is the minimum AC voltage rating of each capacitor?
Shown in the figure below is an "RL" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 9.84 Volts and is running at a frequency of f = 8.585e+04 Hz. The resistor has a resistance of R = 2170 and the inductor has an inductance of L = 3.54e-03 Henries. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Determine the numerical value of Ztot = 2890.5 Determine the numerical value of $z= = 41 Determine the current through the circuit: • I(PEAK) = 4.81E-3 • I(RMS) = 3.404E-3 Determine the voltage across the resistor: • VR(PEAK) = 7.387 • VR(RMS) = 5.22 ✔✔ Amps ✔Amps Write the FORMULA for the phase of the total impedance of the circuit z... = | tan-1 2701 R x Volts X Volts Determine the voltage across the inductor: • VL(PEAK) = 9.184 • VL(RMS) = 6.49 ✔ Volts Volts L R²+ WL- ✔ degrees 2 If a second circuit were connected in parallel with the inductor, this circuit would be considered as: O a low-pass filter O a capacitive switcher…
60. Design a circuit to limit a 20 V rms sinusoidal voltage to a maximum positive amplitude of 10 V and a maximum negative amplitude of -5 V using a single 14 V de voltage source. 61 Datermine the volto in the girRuit F Figura 1 1?
What are the things common in direct current and alternating current. And also its Difference
A resistor & a capacitor are connected in series across 230V, ac supply. The current taken by the circuit is 4 A for 50 Hz frequency. The current is reduced to 2 A, when the frequency of supply is decreased to 40 Hz. Determine the value of resistor & the capacitor.
A generator rated at 30MVA, 11kV has a reactance of 40%. Calculate its p.u. reactances for a base of 50MVA and 10kV. O 0.606 p.u. O 0.506 p.u. O 0.806 p.u. O 0.706 p.u.
In CRO, an alternating current completes 2 cycle in 20 mS. Then its frequency is given by, ...................
2. Refer to the Figure 2. a) Determine the total impedance of the circuit in polar form. b) Determine the voltage v(t) and current i(t) sinusoidal forms. Sketch one cycle of the waveforms in the same x-axis. Clearly indicating the peak value and the period of each waveform and the phase difference (in milliseconds) between the two waveforms. c) Determine the values of resistance R and inductance L. d) Determine the phasors V,, VR and Vc. e) Sketch the phasor diagram showing Vs, Vr, Vr, Vc and I.
Problem Design a circuit to limit a 20 V rms sinusoidal voltage to a maximum positive amplitude of 10 V and a maximum negative amplitude of -5 V using a single 14 V dc voltage source.