4-42. The rectangular gate of Figure 4.63 has a width of 2 m and is exposed to atmospheric pressure on the right side. Find the vertical support reaction force acting at the bottom end of the gate. Water 5 m 45 Hinge pin Gate Air (Patm) 6 m Figure 4.63 System for Exercise 4-42.

4-42. The rectangular gate of Figure 4.63 has a width of 2 m and is exposed to atmospheric pressure on the right side. Find the vertical support reaction force acting at the bottom end of the gate. Water 5 m 45 Hinge pin Gate Air (Patm) 6 m Figure 4.63 System for Exercise 4-42.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The beams ABD and DE are joined by a hinge at D. Select the lightest allowable W-shape for beam DE…

Q: Two rods vertically connect beams AB and CD as shown in the figure. Point A is fixed supported while…

A: To find out the deformation of right rod in mm.

Q: The number of flow channels and head drops is 4 and 12 respectively. If the difference in the…

Q: What is an Service level agreement SLA?

A: It is a commitment between service provider and client that documents what services the provider. It…

Q: 28 The figure below shows a shaft of three segments It is restrained (fixed support) at both sides…

Q: List two (2) forms of Engineering Design and briefly explain each of them.

A: Engineering design is actually defined as the method of the identification and then solving the…

Q: The figure below shows a shaft of three segments It is restrained (fixed support) at both sides and…

Q: A square slab is simply supported on three sides and is free on the fourth side. If the moment…

Q: SUPPLEMENTARY QUESTION The figure shows two reservoirs connected by a pipe. The discharge rate in…

Q: A simply supported beam 300mm x 500mm has a spa unbonded tendons. fse = 750 MPa, Aps = 1200m above…

Q: 5.54 The beams ABD and DE are joined by a hinge at D. Select the lightest al- lowable W-shape for…

A: f (working stress) = 120 MPa

Q: Civil Engineering 6kN.m 2kN/m 2kN A i B i C i D E

A: Given data: Moment diagram:

Q: Given Well graded sand Specific gravity of soil = 2.65 %3D Void ratio = 0.57 Porosity = 36.5% %3D…

A: To Determine Dry unit weight of the soil.

Q: If a G. = 77 2 GPa, G, = 27 GPa and torque of M- = 76 kN.m is applied to induce twisting in the…

Q: Determine the diameter of a steel rod that will carry a tensile load of 50,000kg at a stress of…

Q: 20 kN.m 2 kN/m A- B C T 2m 2m 4m The shear just to the right of C is Select the correct response:

Q: 2. A simply supported beam, 4 in wide by 8 in high and 120 in long is subjected to a concentrated…

Q: What will be the pressure head of a point in mm of Hg if pressure hcad of that point is equal to 63…

Q: A city requires a flow of 25 mgd (million gallons per day) for its water supply. Compute the…

Q: Given in the tabulation below are the observed forward and backward bearings of an open compass…

Q: 3.Discuss the methods of bending tests.

Q: saturated soil has a moisture content of 33% and a specific g ompute the moist unit weight of soil…

Q: The beam AB whose total length is 16 m carrying varying loads from 40 kN/m to 60 kN/m and supported…

A: w1 = 40KN/m w2 = 60KN/m

Q: Explain how to measure the length of a concrete cylinder specimen. When will the counting of test…

A: To measure the length of a concrete cylinder specimen. 1) Use a steel ruler to measure the mold of…

Q: Determine the percentages of gravel, sand, silt, and clay according to the AASHTO System. 1. Gravel…

A: To Determine the percentages of gravel, sand, silt, and clay according to the AASHTO System.

Q: A pipeline carrying oil of specific gravity 0.87 changes in diameter from 200mm diameter at a…

A: To Determine The loss of head and the direction of flow.

Q: A confined aquifer is shown in the figure. The aquifer has a hydraulic conductivity of 23 m/day and…

A: Figure is as shown in the question

Q: In the falling head þeumeability test , in the duration of 3 hours in the initial head of 1000 mm is…

A: Given data- dia=0.5 cm=5 mma=area of stand pipe=π4×52=19.63 mm2dia of soil=10cm=100…

Q: Question 1Z ol 20 The system below shows a solid shaft composed of 2 circular cross sections (r = 15…

Q: The interior angle of a five sided closed traverse were measured as follows: A = 85°11', B = 68°30',…

Q: A simple curve in a highway is to be analyzed. The azimuth angle of its tangent lines are 1116.8…

Q: pove the bottom of the beam f. = 35 MP Reinforced indices for the beam Safe ultimate moment capacity…

A: Given:- 300mm x 500mm span=5m f'c=35MPa Aps=1200mm2 To find:- a) Reinforced indices for the beam b)…

Q: Brine (SG = 1.1, viscosity = 1.1cP) is pumped at a rate of 45 ft^3/min (ID = 2.5in) from large open…

A: Given, Q = 45 ft3/min or 0.75 cfs D = 2.5 in or 0.208 ft

Q: 10 kN/m 20 kN IB C 1 D 4m ㅡ→

Q: Q 1/ The University of Anbar purchased equipment for the purposes of the reconstruction campaign at…

Q: A WT205 × 30 structural steel section (see Appendix B for cross-sectional properties) is used for a…

A: To Find a. Slenderness ratio b. Euler buckling load c. Axial stress in column Given data WT205×30…

Q: Solve the factor of safety, against sliding and 23.5kN overturning, of the 50m high dam (' shown.…

Q: A steel bar 60 mm in diameter and 3 m long is surrounded by a shell of a cast iron 6 mm thick.…

Q: Note: Show all of the diagrams used while solving the problem. Show each and every reaction and…

A: To find out the maximum deflection of simply supported beam.

Q: B- Fill in the Blanks questions 1. The imaginary line representing the boundary of the study area is…

A: 1. Cordon line 2.super power

Q: Explain the difference between sieve analysis between coarse and fine aggregates.

A: The sieve analysis often referred to as the gradation test, is a fundamental test that all aggregate…

Q: For normally consolidated clay specimens, drained direct shear tests were conducted and the…

A: INTRODUCTION; Direct shear test is performed over the soil to calculate the shear strength of soil…

Q: 3. In the Figure 1-61, the incline force P is applied at the center which is necessary to start the…

Q: A simple curve in a highway is to be analyzed . The azimuth angle of its tangent lines are 1,109.6…

A: To Determine The area of the fillet of the simple curve in square meters .

Q: (a) Assuming oallow = 114 MPa, calculate the required section modulus s (in mm3). (At this point,…

Q: F4-6. Determine the moment of the force about point O. 500 N 3 m 45° Prob. F4-6

A: Figure is as shown

Q: A beam with rectangular cross section has b = 50 mm, h =150 mm, E = 210 GPa, and o, = 250 MPa. Find…

Q: 1.8m in fresh water when erect. The scow is 6m wide, 12 long, and 2.4m high. It's center of gravity…

Q: Find call reaction for the freame by slope Deflection method hange B we? 12 4 m 3M 3 M

A: Length of inclined Member AB = 5 m Calculating the fixed end moments Here for fixed end moments…

Q: When the load P is applied to the right end of the cantilever beam, the deflection at the right end…

Question

4-42. The rectangular gate of Figure 4.63 has a width of 2 m and is exposed to atmospheric
pressure on the right side. Find the vertical support reaction force acting at the bottom
end of the gate.
Water
5 m
45
-Hinge pin
Gate
Air (Patm)
6 m
Figure 4.63 System for Exercise 4-42.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

12. Determine the reactions at the supports A and B for equilibrium of the beam. Fig 5-92.
Draw the influence line for member CD. F G H A 3 m E B D -4 panels at 4 m = 16 m %3D
F9-19. Determine the magnitude of the hydrostatic force acting on gate AB, which has a width of 1.5 m. Water has a density of p = 1 Mg/m³. 2 m Ba -1.5 m- Prob. F9-19
Q/ Find the reaction forces at A and B, (A pin connection and B roller connection)? | 120N/m 100N/m B 4m 6m
EXAMPLE 2.8 Draw the SFD and BMD for the beam shown below. 1000 N/m 3m 3m Solution; Calculate the support reactions. 5000N 3m 40000Nm | 3m 3m [Ans: V₁-8000 N (†), V₁-9000 N (1)] 4000N/m
Q/ Find the reaction forces at A and B, (A pin connection and B roller connection)? 120N/m 100N/m А В 4m 6m
Consider the simply-supported overhang beam shown. There is a pin support at A, a roller support at D, and an overhang of 2m. If the pin at A is 10mm in diameter, calculate the shear stress on the pin assuming double shear connection. 5kN/m 2kN/m B C 3m 2m- 1m -2m 2m-
40 k F 20 k 5 ft D 5 ft A C B -5 ft- -5 ft- -5 ft- -5 ft- Determine the Vertical Reaction at A. Ak ert
Q2:-A rectangular gate AB in Fig is I m long and 1.5m wide into the paper, hinged at A. and resting on a smooth bottom at B. The Glycerin of sg- 0.89 acting on the left of gate, What the depth of water h will acting on gate? Water Glyceria 2 m Im 60
Compute the horizontal and vertical components of the hinge at point C and D on the frame system shown. -2m 2.5m 10KN/m В 2.5m E -1.5m -t- 3m -1.5m
30KN 30KN 30KN В 15KN- >15KN 30deg 30deg A 30deg 30deg C R R Compute for the reactions at A,B,C of a 3 Pinned Arch
P12.4 Find redundant Rp. All areas are equal. Dx 60 k 90 k ft Problem 12.4 A D B E 30 ft 30 ft F. 15 ft ft