3.104. The full-wave rectifier in Fig. P3.104 is operating at a frequency of 60 Hz, and the rms value of the transformer output voltage is 18 V. (a) What is the value of the dc output voltage if the diode voltage drop is 1 V? (b) What is the minimum value of C required to maintain the ripple voltage to less than 0.25 V if R = 0.5 2? (c) What is the PIV rating of the diode in this circuit? (d) What is the surge current when power is first applied? (e) What is the amplitude of the repetitive current in the diode? VI JE + VI Figure P3.104 D₁ D₂ K C Hli R 3.105. Repeat Prob. 3.104 if the rms value of the trans- former output voltage v, is 10 V.

3.104. The full-wave rectifier in Fig. P3.104 is operating at a frequency of 60 Hz, and the rms value of the transformer output voltage is 18 V. (a) What is the value of the dc output voltage if the diode voltage drop is 1 V? (b) What is the minimum value of C required to maintain the ripple voltage to less than 0.25 V if R = 0.5 2? (c) What is the PIV rating of the diode in this circuit? (d) What is the surge current when power is first applied? (e) What is the amplitude of the repetitive current in the diode? VI JE + VI Figure P3.104 D₁ D₂ K C Hli R 3.105. Repeat Prob. 3.104 if the rms value of the trans- former output voltage v, is 10 V.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
Text 3.66. Piecewise linear models should be used. Part (a) assumes you assume the diode switches from OFF to ON when the diode voltage is zero volts Part (b) of problem assumes you use the diode model that just includes a 0.65 volt battery when the diode Witshes from OFF to ON. The best systematic approach is to draw out each circuit and then look for any potential contradictions with the diode model and circuit when you assume a diode is either ON or OFF. Sketchina piece-wis linear I-V characteristic is one approach to piece-wise linear problems. Prepare a table to summaize your reis. 1. 3.66. (a) Find I and V in the four circuits in Fig. P3.66 using the ideal diode model. (b) Repeat using the constant voltage drop model with Von =0.65 V. 오 +3 V 오 +5 V 16 k2 o V 16 k2 5 V -7 V - (a) (b) 오 +5 V +7 V 16 k2 -o V 16 k2 -3 V -5 V (c) (d) Figure P3.66
3.56 Consider a half-wave rectifier circuit with a triangular-wave input of 5-V peak-to-peak amplitude and zero average, and with R= 1 k. Assume that the diode can be represented by the constant-voltage-drop model with V₂ = 0.65 V and r = 20 S2. Find the average value of vo.
Text 3.66. Piecewise linear models should be used. Part (a) assumes you assume the diode switches from OFF to ON when the diode voltage is zero volts Part (b) of problem assumes you use the diode model that just includes a 0.65 volt battery when the diode Witehes from OFF to ON. The best systematic approach is to draw out each circuit and then look for any potential contradictions with the diode model and circuit when you assume a diode is either ON or OFF. Sketchinga piece-wis linear I-V characteristic is one approach to piece-wise linear problems. Prepare a table to summaze your res. 1. 3.66. (a) Find I and V in the four circuits in Fig. P3.66 using the ideal diode model. (b) Repeat using the constant voltage drop model with Von = 0.65 V. 9 +3 V +5 V 16 k2 16 k2 6 -5 V -7 V (a) (b) 오 +5 V +7 V 16 k2 V 16 kQ 6 -3 V -5 V (c) (d) Figure P3.66
Given the following circuit with VDD = 9.5 V, R = 3.2 k2, then the current Iis: Use the CVD model for the diode, with VD = 0.65 V. VDD I a. 0 A O b. 0.002766 A c. 0.002969 A d. 2.968750 A e. 2.765625 A R N V₂
In RL load connected (without free transition diode), single phase, uncontrolled, full wave rectifier (4 diodes), the source voltage is sinusoidal and its effective value is 44Volt, 50 Hz. The ohmic load value connected to the circuit is 10 ohms. Average value of load current calculate. (L>>R) a) 4.16 A b) 3.46 A C) 3.26A d) 4.56 A e) 3.96 A
If the positive cycle of the waveform for full wave bridge rectifier , Which of the diodes is working . ..... ...... 10:1 120 V ms Output 60 Hz Puec) RL 220 N Dz 1000µF O D1, D2 D3, D2 D4, D2 D1, D4 not all above D1, D3 ellee
a) What is n-type semiconductor materials? What are the majority and the minority cariers? b) What is p-type semiconductor materials? What are the majority and the minority cariers? c) What is depletion region of a p-n junction diode? d) Describe in your own words the forward-bias and reverse- bias conditions of a p-n junction diode. e) Draw a Diode Symbol and label the anode and the cathode. Si Ge 2 ka f) Find V, in the circuit shown in +20 V 2 k2 15V Fig. Fuad Al-Mannai EENG261 Page 1
Which of the following ratings (PIV- Peak Inverse Voltage and temperature) is true? Si diodes have lower PIV and narrower temperature ranges than Ge diodes. O Si diodes have lower PIV and wider temperature ranges than Ge diodes. Si diodes have higher PIV and narrower temperature ranges than Ge diodes. O Si diodes have higher PIV and wider temperature ranges than Ge diodes. To increase the electrical conductivity of an intrinsic semiconductor, we need to add impurity increase the resistivity apply heat None of the them
Q3: The figure below includes a bridge full-wave rectifier circuit with a diode type is1N4007. The input voltage is Vin V2 120 sin 2n60t 5:1 D3 D1 120 V RL Vp(out) D2 DA 10 kN a) Draw the output voltage waveform for the circuit in the figure and include thevoltage values. b) What is the peak inverse voltage (PIV) across each diode? c) Determine the rms voltage, current and power delivered to RL d) Determine the average voltage, current, and power delivered to RL e) What is the ratio of Po(de) to Po(ac)? lll
Consider the circuit shown in the figure below with Ry=13 ko and R=9 kO. The Zener diode voltage is Vz = 3.5 V, then the currents Iz and , respectively, are equal to: R1 ww 20 V O a. 1.280 mA, 0.789 mA O b. 0.680 mA, 0.189 mA O c. 0.880 mA 0.389 mA O d. 1.080 mA, 0.589 mA
4.) In which mode will a diode generally not conduct electricity? a. Bidirectional Biased b. None of these c. Forward Biased d. Reversed Biased 5.) Consider the following schematic symbol of a semiconductor device: Which side is the Cathode? (Picture inserted down below) a. Side A b. Both side A and B c. Side B d. Neither side A or B 8.) Integrated circuits can be broken down into three basic categories. Which category does an operational amplifier (or op-amp) fall into? a. Analog b. None of these c. A combination of analog and digital d. Digital