23. A tired old inchworm fell into a gopher hole that is 10 inches deep. The worm started climbing up theside of the hole, progressing at the rate of 1 inch every 5 minutes. At the end of each 15 minutes ofclimbing, the worm had to pause to rest for 1 minute. During each of these rest periods, the wormslipped back 1 inch. D201700 dant des movig oil to miss 900 101 coleczons butt bedailn 190m gruntos en CHow many minutes does it take the worm to climb out of the hole?IM NOTAS YOUNGAS I USEDTO BE(+>>) - se odi to ilealbras de buren[8.5.0.2.11-W 399 odd to dusmolamoo ods bui jo bo.d.a.6.1.5.1) Uja] 0

Climb 1 inch in 5 min. in 15 min worm climb = 3 in. after 15 min , it rest for 1 min and slipped 1…

23. A tired old inchworm fell into a gopher hole that is 10 inches deep. The worm started climbing up th side of the hole, progressing at the rate of 1 inch every 5 minutes. At the end of each 15 minutes c climbing, the worm had to a had to pause to rest for 1 minute. to rest for 1 minute. During each of these rest periods, the worm 1999100 nogestion dat dez novig oil to must din 903 10l colors bara bodail 129 190 gru slipped back 1 inch. How many minutes does it take the worm to climb out of the hole?

23. A tired old inchworm fell into a gopher hole that is 10 inches deep. The worm started climbing up th side of the hole, progressing at the rate of 1 inch every 5 minutes. At the end of each 15 minutes c climbing, the worm had to a had to pause to rest for 1 minute. to rest for 1 minute. During each of these rest periods, the worm 1999100 nogestion dat dez novig oil to must din 903 10l colors bara bodail 129 190 gru slipped back 1 inch. How many minutes does it take the worm to climb out of the hole?

Mathematics For Machine Technology

8th Edition

ISBN:9781337798310

Author:Peterson, John.

Publisher:Peterson, John.

Chapter16: Table Of Decimal Equivalents And Combined Operations Of Decimal Fractions

Section: Chapter Questions

Problem 33A: A bronze bushing with a diameter of 22.225 millimeters is to be pressed into a mounting plate. The...

See similar textbooks

Similar questions

A plate 57.20 millimeters thick is to be machined to a thickness of 44.10 millimeters. The plate is to be rough cut with the last cut a finish cut 0.30 millimeter deep. If each rough cut is 3.20 millimeters deep, how many rough cuts are required?
A piece in the shape of a frustum of a pyramid with regular octagon bases is 23.84 centimeters high. The length of each side of the larger base is 8.17 centimeters, and the length of each side of the smaller base is 6.77 centimeters. If a side (s) of a regular octagon is known, its area (A) can be computed by the formula A4.828s2 . Determine the volume of the piece. Round the answer to the nearest cubic centimeter.
A shaft is turned in a lathe at 120 revolutions per minute. The cutting tool advances 0.030 inch per revolution. How bong is the length of cut along the shaft at the end of 3.50 minutes?
A bronze bushing with a diameter of 22.225 millimeters is to be pressed into a mounting plate. The assembly print calls for a bored hole in the plate to be 0.038 millimeter less in diameter than the bushing diameter. The hole diameter in the plate checks 22.103 millimeters. By how much must the diameter of the plate hole be increased in order to meet the print specification?
An automatic screw machine is capable of producing one piece in 0.02 minute. How many pieces can be produced in 1.25 hours?
How much stock per stroke is removed by the wheel of a surface grinder if a depth of 4.725 millimeters is reached after 75 strokes? Round the answer to 3 decimal places.