2. Use the method of sections to determine the internal forces in members JI, DI, and DE. The structure is supported by a pin at A and a roller at G. L K J I 3 m A B Ф C D E Н F |-2 m-|-2 m+++2 m-+-2 m+|+2 m+/-2 m- 20 KN 30 kN 40 kN G

2. Use the method of sections to determine the internal forces in members JI, DI, and DE. The structure is supported by a pin at A and a roller at G. L K J I 3 m A B Ф C D E Н F |-2 m-|-2 m+++2 m-+-2 m+|+2 m+/-2 m- 20 KN 30 kN 40 kN G

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter4: Compression Members

Section: Chapter Questions

Problem 4.7.3P

See similar textbooks

Related questions

Q: P8.10. (a) Compute the horizontal displacement of joint B produced by the 240-kN load in Figure…

Q: The 5 ft diameter cylinder weighs 5000 lbs. and is 5 ft long as shown.compute the horizontal…

Q: For the frame loaded as shown, draw the complete and correct FBDs of the following: whole frame,…

Q: 3. Find the formula for the center of gravity of the shaded area in the figure. The thickness of the…

A: Expression for the center of gravity of the shaded portion. We can say that the center of gravity in…

Q: What are a list of materials used for soil compactor pads (casted alloy materials) . Must have good…

A: Soil compactors are used in the process of compaction. Compaction is the process of removing voids…

Q: draw the moment diagram and shear diagram for the beam

Q: The 5 ft diameter cylinder weighs 5000 lbs. and is 5 ft long as shown.compute the vertical reaction…

A: Diameter of cylinder (d) = 5 ft Length of cylinder (L) = 5 ft Weight of cylinder (W) = 5000 lb…

Q: 12 m 25 kN/m

Q: w=300 lb/ft 15' 1500 lb. * Hint: point B is a hinge, there is only a By force when you draw the FBD,…

A: A beam is given with a fixed end at A, and hinged support at C. The beam also contains an internal…

Q: F & H are incorrect

A: As per question requirment we only find out f and h here. Find out - (f) Length of Curve (h)…

Q: shearing stress in the pin at B and the axi t C are limited to 4040 psi and 5050 psi, r

A: The mechanics deals with the application of forces and reaction forces that are developed in the…

Q: Estimate the effect that a 10°C rise in temperature would have on the percolation rate of leachate…

A: The percolation rate of leachate from a clean landfill can be impacted by a few variables, including…

Q: 0x - 16Мра бу = - 48М ра, т гу - 48 Mpa I 16 Mpa 60 Mpa - 60 Мра

A: State of stress of given as shown- σx=16 MPa,σy=-48 MPa,τxy=60 MPa. To Find- The values of…

Q: Consider the beam below. If the beam is subject to a 20kN internal shear force, determine the…

A: Given:- V= 20 KN thickness of all pieces= 30 mm To find:- The maximum shear stress

Q: 3. Use the AISC Manual Design Tables to select from the list below the angies (LLBB with a gap =…

A: LRFD is based on the idea that the applied loads are scaled up while the strength (resistance) of…

Q: The roof system of a single-storey steel framed building is made up of steel deck supported by OWSJ…

A: a) To determine the total unfactored dead load supported by the steel deck, we need to add up the…

Q: Calculate the total equivalent uniform load in KN/m on Beam BE, if the total floor load is 13.80KPa.…

Q: Consolidated Drained (CD) triaxial tests were performed on clay samples. After the failure, the…

A: Failure plane makes angle of 55o with the horizontal. To find- Effective friction angle of clay.

Q: xfiltration trench is to retain the latory water-quality depth is 2.5 fer is 10 m/d and the trench…

A: Given:- 0.5 ha catchment water quality depth =2.5cm wide=1m deep=1.5m porosity=0.4 To find:-…

Q: A commercial screen cloth of market grade is used to separate different fractions of 300 m3/hr of…

A: Height, h = 3 m Outer Dia. = 9.25 m Thickness = 0.036 m Inner Dia. = 9.25-0.036 = 9.214 m Q = 300…

Q: The data in the table below were obtained in a travel time study on a section of highway using the…

Q: Explain the differences between structural testing and functional testing using examples.

A: A testing strategy called structural testing involves testing the software application's core…

Q: 3' w #/' 8' 3' A A rough cut timber beam, measuring 6" x 14" (b=6"; h=14") is loaded with load (w)…

Q: A sample of clayey silt is mixed at about its liquid limit of 40. It is placed carefully in a small…

A: Here we have to determine the shrinkage limit and dry density

Q: 5. The permeability of 160-acre formation drained by a single well is 15 mD. The well is heavily…

Q: create a water network on this map, the percentage of personal consumption is 0.25 CMD, the number…

A: The Water Supply and Water Resources Division of the United States Environmental Protection Agency…

Q: 4-153. Replace the distributed load. resultant force, and specify its lo measured from O. 3 KM

Q: eBook References A steady, incompressible, two-dimensional velocity field is given by the following…

Q: H = μA In the figure, he, hr, z and the measured slope length I were 5.64 ft, 5.42 ft, 96° 18'56",…

A: Reference : Survey Engineering, Distance measured by Total station Refer above figure ; (mentioned…

Q: SITUATION The homogeneous bar ABCD shown is supported by a cable that. runs from A to B around the…

Q: At the point of operation with maximum efficiency, a turbine indicated unit power of 12 units and…

A: A turbine indicated, Unit speed, Nu=98Unit power, Pu=12Design head, H=8.5 m

Q: A. Determine the reactions to the structure B. Plot the shear and moment diagrams W = 0 kips/ft. A…

Q: A horizontal force of P = 45 kN is applied to joint Cas shown in (Eigure 1). Each pin has a diameter…

A: Shear stress is the force that tends to cause deformation of a material by sliding along a plane.…

Q: Measured infiltration rates, f in cm/hr, for every hour from t=0, when the rainfall just commenced…

A: Given,fo=2.2 cm/hrfc=final constant rate of infiltration=0.7 cm/hrk=4 day−1=4/24hr−1=1/6hr−1Horton's…

Q: ernier (attached to a horizontal circle) to read 25 degrees 12'. The horizontal circle is divided…

A: Given:- horizontal circle=30' 30 divisions To find:- direct circular vernier design

Q: Choose the best W10 and W12 section that can carry the load Given: Axial Load= 141,000 N Fy=…

A: The magnitude of the axial load = 141,000 N The yield strength of the steel (Fy) = 214 MPa The…

Q: On the soil profile shown below, a large oil storage tank of diameter 85m is to be constructed, and…

Q: A small urban watershed located in north of Iraq has four rainfall gauges as located in the figure…

A: The given data is shown below:

Q: Sieve Size 3/4 in. (19 mm) 3/8 in. (9.5 mm) No. 4 (4.25 mm) No. 10 (2 mm) No. 40 (0.425 mm) No. 200…

A: Given, To determine, the suitable ratio for blending aggregates A and B to obtain an acceptable…

Q: 8. Draw the axial force influence lines for the members CD, HD, and HI. D B E A G H I J F · 30 ft…

A: A truss with support and asked to draw the Axial force influence line diagram for the members CD, HD…

Q: A highway survey Pl falls in a pond, so a cut offline AB-275.21 ft is nun between the tangents. In…

A: Degree of curve = 4o30' Angle A = 16o 28' Angle B = 22o16'

Q: ▪ Determine the magnitude of the at-rest lateral earth force, Rankine active/pass unit length of the…

A: H=7m Y=17kN/m3

Q: . You are asked to design a new flexible pavement structure for an existing road that totally…

A: Given:- Existing (old)HMA=135mm Existing(Old)Granular A Base-170mm Existing(Old)Granular B…

Q: Define GIS.

Q: A W30x90 A36 steel girder spans 12 m on simple supports. It carries a uniformly distributed load of…

A: a. To determine the required section modulus, we need to calculate the maximum bending moment the…

Q: Q.2: Closed traverse ABCDE:The lengths of AB = 97.32 m, DE= 112.56 m and EA =107.92 m. The bearing…

A: Solution, whole circle bearing of line ; AB =θ 46*37' (Degree = *) θBC = 180* - 82*40' =…

Q: CIT 105-Homework 6 1. Use the method of joints to determine the internal forces in each member of…

A: Determine the force in each member of the truss using Method of Joints.

Q: Appendix 1 shows a structural drawing of the first floor of a random building. The labels "C"…

A: Structural drawing for the first floor of the building C- Columns D1–4 is a 200 UB 29.8,3C–D is a…

Q: What is temperature susceptibility of asphalt binder? What is the difference between asphalt cement…

A: Context: Asphalt binder, asphalt cement, asphalt emulsion

Q: Check the local buckling and then determine the f strength of a W18X50 of A992 steel with F₁-50 ksi…

A: The instability of the elements that make up the column cross-sections, or plates, without any…

Concept explainers

Load on Structures

Civil engineers primarily deal with beams in their day-to-day applications. A beam is a structural member that resists shear loadings. There are various types of beams such as cantilever beam, simply supported beam, and over the hanging beam. All these beams have a different end and loading conditions.

Question

2. Use the method of sections to determine the internal forces in members JI, DI, and DE.
The structure is supported by a pin at A and a roller at G.
L
J
3 m
K
AN
B
H
E F
C D
2
-2 m--2 m2 m2 m2 m--2 m-
20 KN 30 kN 40 kN
G

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Required answer

VIEW

Step 2: Reaction at G

VIEW

Step 3: Method of sections

VIEW

Solution

VIEW

Step by step

Solved in 4 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Given is a truss structure: Where: Working shear stress for the rivets is 70 MPa Working bearing stress due to rivets is 140 Mpa Thickness of the member is 5 mm Thickness of the Gusset plate is 6 mm Rivet diameter is 15 mm Determine the no. of rivets to fasten the member BD 80 kN 120 kN B. 3 m E 200 kN 4 Panels @ 4 m = 16 m
The 2014-T6 aluminum rod AC is reinforced with the firmly bonded A992 steel tube BC. When no load is applied to the assembly, the gap between end C and the rigid support is 0.5 mm. Determine the support reactions when the axial force of 400 kN is applied. 400 mm 400 kN B A992 steel 50 mm 800 mm 25 mm 2014-T6 aluminum alloy Section a-a -400(10*) N st (a)
A steel pipe (1) is attached to an aluminum pipe (2) at flange B. The pipes are attached to rigid supports at A and C, respectively 18 m 14 m Member (a) has a cross-sectional area A,-3,600 mm2, an elastic modul as a cross-sectional area A 3,600 mm2, an elastic modulus E-200 GPa, and an allowable has a cross-sectional area A2 2,o00 mm2, an elastie modulus E-70 GPa, and an allowable normal stress of 120 MPa. Determine the maximum load Pthat can be applied to fange B without exceeding either allowable stress
Q2/ Segments AB and BC of the assembly below are made from 6061-T6 aluminum. If a couple forces P = 5 kip are applied to the lever arm, Determine (a) the reactions at the fixed supports A and C and (b) the shear stress developed at a point located 1 in. from the center-line of the bar at a cross-section close to point A. 2.5 fi 2.5 ft 6 ft 4 in. 4 in.
4-47. The support consists of a solid red brass C83400 post surrounded by a 304 stainless steel tube. Before the load is applied the gap between these two parts is 1 mm. Determine the greatest axial load that can be applied to the rigid cap A without causing yielding of any one of the materials. A 0.25 m = 1 mm 60 mm 80 mm Prob. 4-47 -10 mm
954. The 2014-T6 aluminum rod AC is reinforced with the firmly bonded A992 steel tube BC. When no laad is applied to the assembly, the gap between end C and the rigid support is 0.5 mm. Determine the support reactions when the axial force of 400 kN is applied. 400 mm 400 kN A992 steel So mm S00 mm 25 mi2014-T6 aluminum alloy Section a-a
For the plate shown, the distance d required to eliminate the flexural .effect at section a - a is 100 mm 200 mm d True O False O -300 mm- a
-5 @ 3m-15m- C F H J K ML boo I A 4@4m=16m B D G E 60 kips A For the truss shown, what is the force in member FG? B what is the force in member BE? + --D
De term ine the kin d and am ount of stress in e ach mem ber of the truss shown by the method of jo in ts in figure P 5-2 (page 76).- 1000lb 1000lb 1000lb 1000Ib 1000 Ib U. h = 20 ft 500lb 500 Ib L. L. RAV 6 pane ls at 10' - 6 ft RBy Note: 1. F o llo w strictly the lecture notes g iv en. Draw the FBD of e ach jo in t 2. Sum m a rize and tabu la te your answers. 3. Compu te the bar forces up to member U,L3 on ly because the truss lo a d in g is sym metric aland the bar forces of right sid e members are id en tic al w ith th e left s ide members. But you in c lu de th e rig ht sid e mem bers in have to the tabu la tion. 4. Show the com puta tio n ho w the leng th s were obta in ed. 5. Look for your own data in the table provided. 6. Copy the problem , data of problem and fig ure of the proble m TABULAT ION FOR SUMMAR Y OF COMPUTATION OF BAR FORCES METHOD OF JOINTS (PROBLEM P5-2 PAGE 76) Mem ber Identification Length Bar Forc e Туре of ft Ib force LOL1 10 3750 Tensio n L1L 2 10 Tension…
Determine the force in members DF, DG, and EG of the roof truss, and state if the members are in tension or compression. The support at A is a pin and the support at L is a roller. You must include a FBD. 1 kN 1 kN 1 kN 1 kN 1 kNI D h = 8 m В OL E G K 2 kN 4 kN 5 kN 6 panels @5 m = 30 m-
Verify the value of Zx for a W1850 that is tabulated in the dimensions and properties tables in Part 1 of the Manual.
Principle of superposition The beam is indeterminate to the first degree. Force in member BD is chosen as the redundant. This member is therefore sectioned to eliminate its capacity to sustain a force. 60 kN/m 3 m 1.8 m 60 45 actual structure (a) 160 kN/m B FaD redundant рrimary structure ARD FRp applied Fap D