17-99. The 12-kg uniform bar is supported by a roller at A.If a horizontal force of F = 80 N is applied to the roller,determine the acceleration of the center of the roller at theinstant the force is applied. Neglect the weight and the sizeof the roller.-AF = 80 N2 m

Given; m=12kg, F=80N Required:-Acceleration of the center of the roller,QCG

Answered: 17-99. The 12-kg uniform bar is…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The handcart has a mass of 200 kg and center of mass at G. Determine the largest magnitude of force P that can be applied to the handle so that the wheels at A or B continue to maintain contact with the ground. Neglect the mass of the wheels. The normal reaction at Ais The normal reaction at B is The acceleration at Gis The greatest value of Pis #KN KN B Ge -0.3m-02 m-04 m- O 0.5 m A
The assembly has a mass of 4 Mg and is hoisted using the winch at B. Determine the greatest acceleration of the assembly so that the compressive force in the hydraulic cylinder supporting the boom does not exceed 180 kN. What is the tension in the supporting cable? The boom has a mass of 2 Mg and mass center at G
The smooth surface of the vertical cam is defined in part by the curve r =(0.2 cos θ + 0.3) m. The forked rod is rotating with an angular acceleration of 2rad/s^2, and when θ = 45° the angular velocity is 6 rad/s. Determine the force the camand the rod exert on the 2-kg roller at this instant. The attached spring has a stiffnessk = 100 N/m and an unstretched length of 0.1 m.
2) The shown spool has a mass of 450 kg and a radius of gyration k. =1.2m. It rests on the surface of conveyer belt for which the coefficient of friction u = 0.5. If the conveyer accelerates at 1.2m/ S²and the spools rolls without slipping, determine the tension in the wire and the angular acceleration of the spool 0.8 m 1.6 m ac
*17-36. The desk has a weight of 75 lb and a center of gravity at G. Determine the initial acceleration of a desk when the man applies enough force Fto overcome the static friction at A and B. Also, find the vertical reactions on each of the two legs at A and at B. The coefficients of static and kinetic friction at A and B are u, = 0.5 and ug = 0.2, respectively. 30° 1 ft 2 ft 2 ft- 2 ft-
17-81. Determine the angular acceleration of the 25-kg diving board and the horizontal and vertical components of reaction at the pin A the instant the man jumps off. Assume that the board is uniform and rigid, and that at the instant he jumps off the spring is compressed a maximum amount of 200 mm, w = 0, and the board is horizontal. Take k = 7 kN/m. E1.5 m -1.5 m -
The 0.2-Kg pin P is constrained to move in the smooth curved slot. Which is defined by the lemniscate r = (0.6 cos20) m. Its motion is controlled by the rotation of the slotted arm OA, which has a constant clockwise angular velocity of 0 = -3 rad/s. Determine (a)-the force arm OA exerts on the pin P when 8 = 0°,note that the motion is in the vertical plane, (b) the acceleration in the r and0 direction. 1= (0.6 cos 26) m A
F13–16. The 0.2-kg pin P is constrained to move in the smooth curved slot, which is defined by the lemniscate r = (0.6 cos 20) m. Its motion is controlled by the rotation of the slotted arm OA, which has a constant clockwise angular velocity of ở = -3 rad/s. Determine the force arm OA exerts on the pin P when e = 0°. Motion is in the vertical plane. 1= (0.6 cos 20) m
The 0.2-Kg pin P is constrained to move in the smooth curved slot. Which is defined by the lemniscate r = (0.6 cos20) m. Its motion is controlled by the rotation of the slotted arm OA, which has a constant clockwise angular velocity of è = -3 rad/s. Determine (a)-the force arm OA exerts on the pin P when 0 = 0°,note that the motion is in the vertical plane, (b) the acceleration in the r and 0 direction. r= (0.6 cos 26) m A اضف ملف ك مستقل عن المسار W العمل الذي قام به شنيع مما بالأعلى لا شيء O jsi آخر
A man pushes the lawn mower at a steady speed with aforce P that is parallel to the incline. The mass of themower with attached grass bag is 50 kg with mass centerat G. If θ = 15°, determine the normal forces NB and NCunder each pair of wheels B and C. Neglect friction. (useg = 9.81 m/s2)NB =NC =
The 200-kg spool has a radius of gyration about its mass center of kg = 300 mm. If the couple moment is applied to the spool and the coefficient of kinetic friction between the spool and the ground is μ = 0.2, determine the angular acceleration of the spool, the acceleration of G and the tension in the cable. 0.4 m B 0.6 m M = 450 N-m
6/40 If the frictional moment at the pivot O is 2 N+m, de- termine the angular acceleration of the grooved drum, which has a mass of 8 kg and a radius of gyra- tion kg = 225 mm. 200 mm kg 12kg

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

17-99. The 12-kg uniform bar is supported by a roller at A. If a horizontal force of F = 80 N is applied to the roller, determine the acceleration of the center of the roller at the instant the force is applied. Neglect the weight and the size of the roller. -A F = 80 N 2 m